Nissan Cube. Manual - part 1035

 

  Index      Nissan     Nissan Cube (2014 year) - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1033  1034  1035  1036   ..

 

 

Nissan Cube. Manual - part 1035

 

 

C1716, C1717, C1718, C1719 TIRE PRESSURE SENSOR

WT-31

< DTC/CIRCUIT DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

C1716, C1717, C1718, C1719 TIRE PRESSURE SENSOR

DTC Logic

INFOID:0000000009949864

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

DTC REPRODUCTION PROCEDURE

With CONSULT

1.

Turn the ignition switch ON.

CAUTION:

Never start the engine.

2.

Check the tire pressure for all wheels and adjust to the specified value. Refer to 

WT-54, "Tire Air Pres-

sure"

3.

Perform “SELF-DIAG RESULTS” in “AIR PRESSURE MONITOR” of “BCM”.

Is DTC “C1716”, “C1717”, “C1718”, “C1719” detected?

YES

>> Perform trouble diagnosis. Refer to 

WT-31, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009949865

1.

CHECK TIRE PRESSURE

Check the internal pressure of all wheels. Refer to 

WT-54, "Tire Air Pressure"

Is the inspection result normal?

YES

>> Replace the DTC-detected malfunctioning tire pressure sensor. Refer to 

WT-48, "WITH INTELLI-

GENT KEY : Removal and Installation"

 (With intelligent key system), 

WT-51, "WITHOUT INTELLI-

GENT KEY : Removal and Installation"

 (Without intelligent key system).

NO

>> After adjusting the tire pressure, GO TO 2.

2.

CHECK TIRE PRESSURE SIGNAL

With CONSULT

1.

Check and adjust the tire pressure for all wheels. Refer to 

WT-54, "Tire Air Pressure"

2.

Perform tire pressure sensor ID registration for all wheels. Refer to 

WT-24, "Work Procedure"

3.

Drive for 3 minutes at a speed of 40 km/h (25 MPH) or more, then drive normally for 10 minutes.

4.

Perform “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”.

5.

Select “BCM” in “DATA MONITOR”, and check that the tire pressures match the standard value.

CAUTION:

Stop the vehicle and within 15 minutes, use CONSULT “DATA MONITOR” to display the tire pres-
sure for all wheels.

6.

Check that “DATA MONITOR” displays tire pressure of 438.60 kPa (4.47 kg/cm

2

, 63.60 Psi).

Is the inspection 438.60 kPa (4.47 kg/cm

2

, 63.60 Psi)?

YES

>> Replace tire pressure sensor the tire pressure 438.60 kPa (4.386 bar, 4.47 kg/cm

2

, 63.60 Psi) dis-

played. Refer to 

WT-48, "WITH INTELLIGENT KEY : Removal and Installation"

 (With intelligent

key system), 

WT-51, "WITHOUT INTELLIGENT KEY : Removal and Installation"

 (Without intelli-

gent key system).

NO

>> GO TO 1.

DTC

Display item

Malfunction detected condition

Possible case

C1716

[PRESSDATA ERR] FL

Malfunction in the tire pressure data from the front left 
wheel tire pressure sensor.

• Excessive tire pressure
• ID registration is not fin-

ished

• Tire pressure sensor mal-

function

C1717

[PRESSDATA ERR] FR

Malfunction in the tire pressure data from the front right 
wheel tire pressure sensor.

C1718

[PRESSDATA ERR] RR

Malfunction in the tire pressure data from the rear right 
wheel tire pressure sensor.

C1719

[PRESSDATA ERR] RL

Malfunction in the tire pressure data from the rear left wheel 
tire pressure sensor.

WT-32

< DTC/CIRCUIT DIAGNOSIS >

C1716, C1717, C1718, C1719 TIRE PRESSURE SENSOR

Special Repair Requirement

INFOID:0000000009949866

1.

CHECK TIRE PRESSURE

Check all tires for tire pressures. Refer to 

WT-54, "Tire Air Pressure"

.

Does all tire pressure data meet the specification?

YES

>> GO TO 2.

NO

>> Inspect or repair the tires or wheels and adjust the tire pressure to the specification.

2.

PERFORM ID REGISTRATION

Perform ID registration. Refer to 

WT-24, "Work Procedure"

.

>> END

C1729 VEHICLE SPEED SIGNAL

WT-33

< DTC/CIRCUIT DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

C1729 VEHICLE SPEED SIGNAL

Description

INFOID:0000000009949867

BCM detects no vehicle speed signal.

DTC Logic

INFOID:0000000009949868

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

DTC REPRODUCTION PROCEDURE

With CONSULT

1.

Drive for several minutes at a speed of 40 km/h (25 MPH) or more, then stop the vehicle.

2.

Perform “SELF-DIAG RESULTS” in “AIR PRESSURE MONITOR” of “BCM”.

Is DTC “C1729” detected?

YES

>> Perform trouble diagnosis. Refer to 

WT-33, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009949869

1.

PERFORM COMBINATION METER SELF-DIAGNOSIS

With CONSULT

Perform “SELF-DIAG RESULTS” of “METER/M&A”.
Is any DTC detected?

YES

>> Check the DTC. Refer to 

MWI-62, "DTC Index"

.

NO

>> GO TO 2.

2.

CHECK INFORMATION

With CONSULT

1.

Perform “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”.

2.

Select “BCM” in “DATA MONITOR”, and check the input/output values. Refer to 

BCS-49, "Reference

Value"

 (With intelligent key system), 

BCS-128, "Reference Value"

 (Without intelligent key system). 

Is the inspection result normal?

YES

>> Check pin terminal and connection of each harness connector for malfunctioning conditions. 

NO

>> Replace BCM. Refer to 

BCS-88, "Exploded View"

 (With intelligent key system), 

BCS-155,

"Exploded View"

 (Without intelligent key system). 

Special Repair Requirement

INFOID:0000000009949870

1.

CHECK TIRE PRESSURE

Check all tires for tire pressures. Refer to 

WT-54, "Tire Air Pressure"

.

Does all tire pressure data meet the specification?

YES

>> GO TO 2.

NO

>> Inspect or repair the tires or wheels and adjust the tire pressure to the specification.

2.

PERFORM ID REGISTRATION

Perform ID registration. Refer to 

WT-24, "Work Procedure"

.

>> END

DTC 

Display item

Malfunction detected condition

Possible case

C1729

VHCL SPEED SIG ERR

Vehicle speed signal not detected.

• CAN communication error
• Combination meter malfunction

WT-34

< DTC/CIRCUIT DIAGNOSIS >

LOW TIRE PRESSURE WARNING LAMP

LOW TIRE PRESSURE WARNING LAMP

Component Function Check

INFOID:0000000009949871

1.

CHECK THE ILLUMINATION OF THE LOW TIRE PRESSURE WARNING LAMP

Check that the low tire pressure warning lamp is turned OFF after illuminating for approximately 1 second,
when the ignition switch is turned ON.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Perform trouble diagnosis. Refer to 

WT-34, "Diagnosis Procedure"

Diagnosis Procedure

INFOID:0000000009949872

1.

POWER SUPPLY AND GROUND CIRCUIT

Check power supply and ground circuit. Refer to 

WT-35, "Diagnosis Procedure"

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace damaged parts.

2.

PERFORM SELF-DIAGNOSIS

With CONSULT

Perform “SELF-DIAG RESULTS” in “AIR PRESSURE MONITOR” of “BCM”.
Is any DTC detected?

YES

>> Check the DTC. Refer to 

BCS-82, "DTC Index"

 (With intelligent key system), 

BCS-150,

"DTC Index"

 (Without intelligent key system). 

NO

>> GO TO 3.

3.

CHECK LOW TIRE PRESSURE WARNING LAMP SIGNAL

With CONSULT

1.

Turn the ignition switch ON.

CAUTION:

Never start the engine.

2.

Perform “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”.

3.

Select “BCM” in “DATA MONITOR”, and check that the low tire pressure warning lamp is turned OFF after
illuminating for approximately 1 second, when the ignition switch is turned ON.

Is the inspection result normal?

YES

>> Check the combination meter. Refer to 

MWI-39, "COMBINATION METER : Diagnosis Procedure"

.

NO

>> Replace the BCM. Refer to 

BCS-88, "Exploded View"

 (With intelligent key system), 

BCS-155,

"Exploded View"

 (Without intelligent key system). 

 

 

 

 

 

 

 

Content   ..  1033  1034  1035  1036   ..