Nissan Cube. Manual - part 1034

C1704, C1705, C1706, C1707 LOW TIRE PRESSURE

WT-27

< DTC/CIRCUIT DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

CAUTION:

Stop the vehicle and within 5 minutes, use “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”
to display the tire pressure for all wheels.
Is the inspection result normal?

YES

>> Inspect or repair the tires or wheels and adjust the tire pressure to the specification.

NO

>> GO TO 1.

Special Repair Requirement

INFOID:0000000009949860

1.

CHECK TIRE PRESSURE

Check all tires for tire pressures. Refer to 

WT-54, "Tire Air Pressure"

.

Does all tire pressure data meet the specification?

YES

>> GO TO 2.

NO

>> Inspect or repair the tires or wheels and adjust the tire pressure to the specification.

2.

PERFORM ID REGISTRATION

Perform ID registration. Refer to 

WT-24, "Work Procedure"

.

>> END

Monitor item

Condition

Displayed value

AIR PRESS FL

Drive for 3 minutes at a speed of 40 km/h (25 MPH) or 
more, then drive normally for 10 minutes.

Internal pressure of tires

AIR PRESS FR

AIR PRESS RR

AIR PRESS RL

WT-28

< DTC/CIRCUIT DIAGNOSIS >

C1708, C1709, C1710, C1711 TIRE PRESSURE SENSOR

C1708, C1709, C1710, C1711 TIRE PRESSURE SENSOR

DTC Logic

INFOID:0000000009949861

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

TIRE PRESSURE SENSOR ID REGISTRATION

Perform tire pressure sensor ID registration. Refer to 

WT-24, "Work Procedure"

.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION 

With CONSULT

1.

Drive the vehicle at 40 km/h or more for 10 minutes.

CAUTION:

Total time driving at a speed of 40 km/h or more must be 10 minutes.
NOTE:
Avoid driving in area where radio wave cannot be transmitted/received.

2.

Stop the vehicle.

3.

Perform self-diagnosis for “AIR PRESSURE MONITOR” of “BCM”.

Is DTC “C1708”, “C1709”, “C1710” or “C1711” detected?

YES

>> Proceed to 

WT-28, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009949862

1.

CHECK TIRE PRESSURE SIGNAL

With CONSULT

1.

Select “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”.

2.

Check the values that are displayed for “AIR PRESS FL”, “AIR PRESS FR”, “AIR PRESS RR”, and “AIR
PRESS RL”.

Are all tire pressures displayed 0 kPa (psi)?

YES (With intelligent key system)>>GO TO 2.
YES (Without intelligent key system)>>GO TO 4.
NO

>> Replace applicable tire pressure sensor. Refer to 

WT-48, "WITH INTELLIGENT KEY : Removal

and Installation"

 (With intelligent key system), 

WT-51, "WITHOUT INTELLIGENT KEY : Removal

and Installation"

 (Without intelligent key system).

2.

CHECK RECEIVER CIRCUIT

1.

Turn the ignition switch OFF.

2.

Check 10A fuse (#13).

CAUTION:

Check that the fuse is not blown, that there are no other abnormalities, and that the fuse is of the
specified capacity.

3.

Disconnect BCM harness connector and tire pressure receiver harness connector.

DTC

Display Item

Malfunction detected condition

Possible causes

C1708

[NO DATA] FL

Tire pressure data signal from the front LH wheel 
tire pressure sensor cannot be detected.

• Harness or connector

(Tire pressure receiver, BCM)

• Tire pressure sensor ID regis-

tration incomplete

• Tire pressure sensor
• Tire pressure sensor battery 

voltage

• Driving in area where radio 

wave cannot be transmitted/re-
ceived.

C1709

[NO DATA] FR

Tire pressure data signal from the front RH wheel 
tire pressure sensor cannot be detected.

C1710

[NO DATA] RR

Tire pressure data signal from the rear RH wheel 
tire pressure sensor cannot be detected.

C1711

[NO DATA] RL

Tire pressure data signal from the rear LH wheel 
tire pressure sensor cannot be detected.

C1708, C1709, C1710, C1711 TIRE PRESSURE SENSOR

WT-29

< DTC/CIRCUIT DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

4.

Check the continuity between BCM harness connector and tire pressure receiver harness connector.

5.

Check the continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace error-detected parts.

3.

CHECK TIRE PRESSURE RECEIVER POWER SUPPLY CIRCUIT

1.

Connect tire pressure receiver harness connector.

2.

Check the voltage between tire pressure receiver harness connector and the ground when the ignition
switch is turned ON and OFF.

CAUTION:

Never start the engine.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace error-detected parts.

4.

CHECK RECEIVER CIRCUIT

1.

Turn the ignition switch OFF.

2.

Disconnect BCM harness connector and tire pressure receiver harness connector.

3.

Check the continuity between BCM harness connector and tire pressure receiver harness connector.

4.

Check the continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace error-detected parts.

5.

CHECK TIRE PRESSURE RECEIVER POWER SUPPLY CIRCUIT

BCM

Tire pressure receiver

Continuity

Connector

Terminal

Connector

Terminal

M68

18

M87

4

Existed

38

2

BCM

—

Continuity

Connector

Terminal

M68

18

Ground

Not existed

38

Tire pressure receiver

—

Voltage

Connector

Terminal

M87

1

Ground

9 – 16 V

BCM

Tire pressure receiver

Continuity

Connector

Terminal

Connector

Terminal

M65

18

M61

1

Existed

19

4

20

2

BCM

—

Continuity

Connector

Terminal

M65

18

Ground

Not existed

19

20

WT-30

< DTC/CIRCUIT DIAGNOSIS >

C1708, C1709, C1710, C1711 TIRE PRESSURE SENSOR

1.

Connect tire pressure receiver harness connector.

2.

Check the voltage between tire pressure receiver harness connector and the ground when the ignition
switch is turned ON and OFF.

CAUTION:

Never start the engine.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Replace the BCM.

6.

CHECK TIRE PRESSURE SIGNAL

Check the function tire pressure receiver. Refer to 

DLK-75, "Component Function Check"

 (With intelligent

key system), 

DLK-280, "Wiring Diagram - REMOTE KEYLESS ENTRY SYSTEM -"

 (Without intelligent key

system).

Is the inspection result normal?

YES

>> Replace the BCM.

NO

>> Repair or replace error-detected parts.

Special Repair Requirement

INFOID:0000000009949863

1.

CHECK TIRE PRESSURE

Check all tires for tire pressures. Refer to 

WT-54, "Tire Air Pressure"

.

Does all tire pressure data meet the specification?

YES

>> GO TO 2.

NO

>> Inspect or repair the tires or wheels and adjust the tire pressure to the specification.

2.

PERFORM ID REGISTRATION

Perform ID registration. Refer to 

WT-24, "Work Procedure"

.

>> END

Tire pressure receiver

—

Voltage

Connector

Terminal

M61

1

Ground

9 – 16 V