Nissan Cube. Manual - part 65

BCS

DIAGNOSIS SYSTEM (BCM)

BCS-109

< SYSTEM DESCRIPTION >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

ACTIVE TEST

WORK SUPPORT

HEADLAMP

HEADLAMP : CONSULT Function (BCM - HEAD LAMP)

INFOID:0000000010249179

WORK SUPPORT

Test item

Description

INT LAMP

This test is able to check interior room lamp operation
• On: Operate
• Off: Non-operation

FLASHER

This test is able to check flasher operation [LH/RH/Off]

HORN

This test is able to check horn operation
• On: Operate

Test item

Description

REMO CONT IN REGIST

Keyfob ID code can be registered

REMO CONT IN ERASUR

Keyfob ID code can be erased

REMO CONT IN CONFIR

It can be checked whether Intelligent Key ID code is registered or not in this mode

MULTI ANSWER BACK SET

NOTE:
This item is displayed, but cannot be tested

HORN CHIRP SET

Hazard and horn reminder function (horn operation) mode can be changed in this mode
• On: Operate
• Off: Non-operation

HAZARD LAMP SET

Hazard and horn reminder function (hazard operation) mode can be changed in this mode
• MODE1: Non-operation
• MODE2: Unlock operation only
• MODE3: Lock operation only
• MODE4: Lock and unlock operation

AUTO LOCK SET

Auto door lock time can be changed in this mode
• MODE 1: Non-operation
• MODE 2: 30 sec
• MODE 3: 1 minute
• MODE 4: 2 minute
• MODE 5: 3 minute
• MODE 6: 4 minute
• MODE 7: 5 minute

PANIC ALARM SET

Panic alarm button pressing time on keyfob remote control button can be selected from the 
following with this mode
• MODE1: 0.5 sec
• MODE2: Non-operation
• MODE3: 1.5 sec

TRUNK OPEN SET

NOTE:
This item is displayed, but cannot be tested

Service item

Setting 

item

Setting

BATTERY SAVER SET

On*

With the exterior lamp battery saver function

Off

Without the exterior lamp battery saver function

BCS-110

< SYSTEM DESCRIPTION >

[WITHOUT INTELLIGENT KEY SYSTEM]

DIAGNOSIS SYSTEM (BCM)

*: Factory setting

DATA MONITOR

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

ILL DELAY SET

MODE 1

NOTE:
This item is displayed, but cannot be used

MODE 2

MODE 3

MODE 4

MODE 5

MODE 6

MODE 7

MODE 8

AUTO LIGHT LOGIC SET

MODE 1

NOTE:
This item is displayed, but cannot be used

MODE 2

MODE 3

MODE 4

MODE 5

MODE 6

Service item

Setting 

item

Setting

Monitor item

[Unit]

Description

IGN ON SW
[On/Off]

Indicated [On/Off] condition of ignition switch in ON position

ACC ON SW
[On/Off]

Indicates [On/Off] condition of ignition switch in ACC position

HI BEAM SW
[On/Off]

Each switch status that BCM judges from the combination switch reading function

HEAD LAMP SW 1
[On/Off]

HEAD LAMP SW 2
[On/Off]

TAIL LAMP SW
[On/Off]

AUTO LIGHT SW*
[On/Off]

PASSING SW
[On/Off]

FR FOG SW*
[On/Off]

DOOR SW-DR
[On/Off]

Indicated [On/Off] condition of front door switch (driver side)

DOOR SW-AS
[On/Off]

Indicated [On/Off] condition of front door switch (passenger side)

DOOR SW-RR
[On/Off]

Indicated [On/Off] condition of rear door switch RH

DOOR SW- RL
[On/Off]

Indicated [On/Off] condition of rear door switch LH

BCS

DIAGNOSIS SYSTEM (BCM)

BCS-111

< SYSTEM DESCRIPTION >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

*: This item is displayed, but cannot be monitored.

ACTIVE TEST

WIPER

WIPER : CONSULT Function (BCM - WIPER)

INFOID:0000000010249183

WORK SUPPORT

*:Factory setting

DATA MONITOR

NOTE:

BACK DOOR SW
[On/Off]

Indicated [On/Off] condition of back door switch

TURN SIGNAL R
[On/Off]

Each switch status that BCM judges from the combination switch reading function

TURN SIGNAL L
[On/Off]

KEY ON SW
[On/Off]

Indicated [On/Off] condition of key switch

KEYLESS LOCK
[On/Off]

Indicated [On/Off] condition of lock signal from key fob

PKB SW
[On/Off]

The parking brake switch status received from combination meter with CAN communica-
tion

ENGINE RUN
[On/Off]

The engine status received from ECM with CAN communication

VEHICLE SPEED
[km/h]

Display the vehicle speed signal received from combination meter by numerical value 
[Km/h]

OPTI SEN (DTCT)
[V]

NOTE:
This item is displayed, but cannot be monitored

OPTI SEN (FILT)
[V]

NOTE:
This item is displayed, but cannot be monitored

Monitor item

[Unit]

Description

Test item

Operation

Description

TAIL LAMP

On

Transmits the position light request signal to IPDM E/R with CAN commu-
nication to turn the tail lamp ON.

Off

Stops the tail lamp request signal transmission.

HEAD LAMP

Hi

Transmits the high beam request signal with CAN communication to turn 
the headlamp (HI).

Lo

Transmits the low beam request signal with CAN communication to turn the 
headlamp (LO).

Off

Stops the high & low beam request signal transmission.

FR FOG LAMP

On

NOTE:
This item is displayed, but cannot be tested

Off

ILL DIM SIGNAL

On

NOTE:
This item is displayed, but cannot be tested

Off

Service item

Setting item

Description

WIPER SPEED 
SETTING

On

With vehicle speed
(Front wiper intermittent time linked with the vehicle speed and wiper intermittent dial position)

Off*

Without vehicle speed
(Front wiper intermittent time linked with the wiper intermittent dial position)

BCS-112

< SYSTEM DESCRIPTION >

[WITHOUT INTELLIGENT KEY SYSTEM]

DIAGNOSIS SYSTEM (BCM)

The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

ACTIVE TEST

FLASHER

FLASHER : CONSULT Function (BCM - FLASHER)

INFOID:0000000010249180

DATA MONITOR

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

Monitor Item

[Unit]

Description

IGN ON SW
[On/Off]

Ignition switch ON status judged from ignition power supply.

IGN SW CAN
[On/Off]

Ignition switch ON status received from IPDM E/R with CAN communication.

FR WIPER HI
[On/Off]

Each switch status that BCM judges from the combination switch reading function.

FR WIPER LOW
[On/Off]

FR WIPER INT
[On/Off]

FR WASHER SW
[On/Off]

INT VOLUME
[1 

−

 7] 

Each switch status that BCM judges from the combination switch reading function.

FR WIPER STOP
[On/Off]

Front wiper motor (stop position) status received from IPDM E/R with CAN communication.

VEHICLE SPEED 
[km/h]

The value of the vehicle speed signal received from combination meter with CAN communication.

RR WIPER ON
[On/Off]

Each switch status that BCM judges from the combination switch reading function.

RR WIPER INT
[On/Off]

RR WASHER SW
[On/Off]

REVERSE SW CAN
[On/Off]

NOTE:
The item is indicated, but not monitored.

RAIN SENSOR
[On/Off]

Test item

Operation

Description

FR WIPER

Hi

Transmits the front wiper request signal (HI) to IPDM E/R with CAN communication to 
operate the front wiper HI operation.

Lo

Transmits the front wiper request signal (LO) to IPDM E/R with CAN communication to 
operate the front wiper LO operation.

INT

Transmits the front wiper request signal (INT) to IPDM E/R with CAN communication to 
operate the front wiper INT operation.

Off

Stops transmitting the front wiper request signal to stop the front wiper operation.

RR WIPER

On

Outputs the voltage to operate the rear wiper motor.

Off

Stops the voltage to stop.