Nissan Versa Note. Manual - part 706

B2620 PARK/NEUTRAL POSITION SWITCH

SEC-103

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

3.

CHECK PARK/NEUTRAL POSITION SWITCH POWER SUPPLY 

1. Turn ignition switch OFF.

2. Disconnect park/neutral position switch connector.

3. Turn ignition switch ON.

4. Check voltage between park/neutral position switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK PARK/NEUTRAL POSITION SWITCH INPUT SIGNAL 

1. Turn ignition switch OFF.

2. Connect park/neutral position switch connector.

3. Turn ignition switch ON.

4. Check voltage between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> GO TO 6.

5.

REPLACE BCM

1. Replace BCM. Refer to 

BCS-70, "Removal and Installation"

.

2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT. Refer to the CON-

SULT Immobilizer mode and follow the on-screen instructions.

>> Inspection End

6.

CHECK PARK/NEUTRAL POSITION SWITCH SIGNAL CIRCUIT 

1. Turn ignition switch OFF.

2. Disconnect park/neutral position switch connector.

3. Disconnect BCM connector.

4. Check continuity between park/neutral position switch harness connector and BCM harness connector.

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Repair or replace harness.

7.

CHECK PARK/NEUTRAL POSITION SWITCH

Refer to 

SEC-104, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 8.

NO 

>> Replace park/neutral position switch. Refer to 

TM-19, "Removal and Installation"

.

(+)

(–)

Voltage (V)

(Approx.)

Park/neutral position switch

Connector

Terminal

F24

1

Ground

Battery voltage

(+)

(–)

Condition

Voltage

BCM

Connector

Terminal

M98

102

Ground

Shift lever

Neutral position

Battery voltage

Except neutral position 

0 – 1.5 V

Park/neutral position switch

BCM

Continuity

Connector

Terminal

Connector

Terminal

F24

2

M98

102

Yes

SEC-104

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

B2620 PARK/NEUTRAL POSITION SWITCH

8.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-41, "Intermittent Incident"

.

>> Inspection End

Component Inspection

INFOID:0000000009705910

1.

CHECK PARK/NEUTRAL POSITION SWITCH

1. Turn ignition switch OFF.

2. Disconnect park/neutral position switch connector.

3. Check continuity between park/neutral position switch terminals.

Is the inspection result normal?

YES

>> Inspection End

NO

>> Replace park/neutral position switch. Refer to 

TM-19, "Removal and Installation"

.

Park/neutral position switch

Condition

Continuity

Terminal

1

2

Shift lever

Neutral position

Yes

Except neutral position

No

B26E8 CLUTCH INTERLOCK SWITCH

SEC-105

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

B26E8 CLUTCH INTERLOCK SWITCH

DTC Logic

INFOID:0000000009705911

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE 1

1. Turn ignition switch ON.

2. Wait 2 seconds or more under the following conditions.

-

Shift lever: In the neutral position.

-

Clutch pedal: Depressed

3. Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.
Is DTC detected?

YES >> Go 

to 

SEC-105, "Diagnosis Procedure"

.

NO

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE 2

1. Release clutch pedal and wait 2 seconds or more.

2. Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.
Is DTC detected?

YES >> Go 

to 

SEC-105, "Diagnosis Procedure"

.

NO

>> Inspection End

Diagnosis Procedure

INFOID:0000000009705912

Regarding Wiring Diagram information, refer to 

SEC-40, "Wiring Diagram"

.

1.

CHECK DTC OF COMBINATION METER

Check DTC in “Self Diagnostic Result” mode of “METER/M&A” using CONSULT.

Refer to 

MWI-21, "DTC Index"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CHECK FUSE

1. Turn power switch OFF.

2. Check that the following fuse in the fuse block (J/B) is not blown.

Is the inspection result normal?

DTC No.

CONSULT screen items

(Trouble diagnosis content)

DTC detecting condition

Possible cause

B26E8

CLUTCH SW
(Clutch switch)

BCM detects the following conditions for 2 
seconds or more.
• Clutch pedal position switch: ON

(Clutch pedal is released)

• Clutch interlock switch: ON

(Clutch pedal is depressed)

• Harness or connector

(Clutch interlock switch circuit is 
open or shorted)

• Harness or connector

(Clutch pedal position switch circuit 
is open or shorted)

• Clutch interlock switch 
• Clutch pedal position switch 
• BCM

Signal name

Fuse No.

Ignition power supply

10 (10 A)

SEC-106

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

B26E8 CLUTCH INTERLOCK SWITCH

YES

>> GO TO 3.

NO

>> Replace the blown fuse after repairing the cause of blowing.

3.

CHECK CLUTCH INTERLOCK SWITCH POWER SUPPLY

1. Disconnect clutch interlock switch connector.

2. Turn ignition switch ON.

3. Check voltage between clutch interlock switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK CLUTCH INTERLOCK SWITCH SIGNAL 

1. Connect clutch interlock switch connector.

2. Check voltage between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> GO TO 6.

5.

REPLACE BCM

1. Replace BCM. Refer to 

BCS-70, "Removal and Installation"

.

2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT. Refer to the CON-

SULT Immobilizer mode and follow the on-screen instructions.

>> Inspection End

6.

CHECK CLUTCH INTERLOCK SWITCH CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect BCM connector.

3. Check continuity between clutch interlock switch harness connector and BCM harness connector.

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Repair or replace harness.

7.

CHECK CLUTCH INTERLOCK SWITCH

Refer to 

SEC-101, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 8.

NO

>> Replace clutch interlock switch. Refer to 

CL-10, "Exploded View"

.

8.

CHECK INTERMITTENT INCIDENT

(+)

(–)

Voltage (V)

(Approx.)

Clutch interlock switch

Connector

Terminal

E34

1

Ground

Battery voltage

(+)

(–)

Condition

Voltage

BCM

Connector

Terminal

M98

101

Ground

Clutch pedal

Released

6 – 16 V

Depressed

0 – 1.5 V

Clutch interlock switch

BCM

Continuity

Connector

Terminal

Connector

Terminal

E34

2

M98

101

Yes