Nissan Versa Note. Manual - part 707

 

  Index      Nissan     Nissan Versa Note (2014 year) - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  705  706  707  708   ..

 

 

Nissan Versa Note. Manual - part 707

 

 

B26E8 CLUTCH INTERLOCK SWITCH

SEC-107

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

Refer to 

GI-41, "Intermittent Incident"

.

>> Inspection End

Component Inspection (Clutch Interlock Switch)

INFOID:0000000009705913

1.

CHECK CLUTCH INTERLOCK SWITCH

1. Turn ignition switch OFF.

2. Disconnect clutch interlock switch connector.

3. Check continuity between clutch interlock switch terminals.

.

Is the inspection result normal?

YES

>> Inspection End

NO

>> Replace clutch interlock switch. Refer to 

CL-10, "Exploded View"

.

Clutch interlock switch

Condition

Continuity

Terminal

1

2

Clutch pedal

Depressed

Yes

Not depressed

No

SEC-108

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

B26F3 STARTER CONTROL RELAY

B26F3 STARTER CONTROL RELAY

DTC Logic

INFOID:0000000009705914

DTC DETECTION LOGIC

NOTE:

• If DTC B26F3 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to

BCS-60, "DTC Logic"

.

• If DTC B26F3 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to

BCS-61, "DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Press push-button ignition switch under the following conditions to start engine.

-

Selector lever: In the P position

-

Brake pedal: Not depressed

2. Wait 2 seconds after engine started.

3. Check DTC in Self Diagnostic Result mode of BCM using CONSULT.
Is DTC detected?

YES

>> Go to 

SEC-108, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000009705915

1.

CHECK DTC OF IPDM E/R

Check DTC in Self Diagnostic Result mode of IPDM E/R using CONSULT.
Is DTC detected?

YES

>> Perform the diagnosis procedure related to the detected DTC. Refer to 

PCS-21, "DTC Index"

.

NO

>> GO TO 2.

2.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-41, "Intermittent Incident"

.

>> Inspection End.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B26F3

START CONT RLY ON

BCM requests IPDM E/R to turn starter 
control relay OFF, but BCM cannot receive 
starter control relay OFF state signal from 
IPDM E/R (CAN).

• Harness or connectors

(The CAN communication line is open 
or shorted.)

• IPDM E/R

B26F4 STARTER CONTROL RELAY

SEC-109

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

B26F4 STARTER CONTROL RELAY

DTC Logic

INFOID:0000000009705916

DTC DETECTION LOGIC

NOTE:

• If DTC B26F4 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to

BCS-60, "DTC Logic"

.

• If DTC B26F4 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to

BCS-61, "DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Press push-button ignition switch under the following conditions to start engine, and wait 1 second or

more.

-

Selector lever: In the P position

-

Brake pedal: Not depressed

2. Check DTC in Self Diagnostic Result mode of BCM using CONSULT.
Is DTC detected?

YES

>> Go to 

SEC-109, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000009705917

1.

CHECK DTC OF IPDM E/R

Check DTC in Self Diagnostic Result mode of IPDM E/R using CONSULT.
Is DTC detected?

YES

>> Perform the diagnosis procedure related to the detected DTC. Refer to 

PCS-21, "DTC Index"

.

NO

>> GO TO 2.

2.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-41, "Intermittent Incident"

.

>> Inspection End.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B26F4

START CONT RLY OFF

BCM requests IPDM E/R to turn starter 
control relay ON, but BCM cannot receive 
starter control relay ON state signal from 
IPDM E/R (CAN).

• Harness or connectors

(The CAN communication line is open 
or shorted.)

• IPDM E/R

SEC-110

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

B26F7 BCM

B26F7 BCM

DTC Logic

INFOID:0000000009705918

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Press door request switch.

2. Turn ignition switch ON.

3. Check DTC in Self Diagnostic Result mode of BCM using CONSULT.
Is DTC detected?

YES

>> Go to 

SEC-110, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000009705919

1.

INSPECTION START

1. Turn ignition switch ON.

2. Select Self Diagnostic Result mode of BCM using CONSULT.

3. Touch ERASE.

4. Perform DTC CONFIRMATION PROCEDURE for DTC B26F7. Refer to 

SEC-110, "DTC Logic"

.

Is DTC B26F7 detected again?

YES

>> GO TO 2.

NO

>> Inspection End.

2.

REPLACE BCM

1. Replace BCM. Refer to 

BCS-70, "Removal and Installation"

.

2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT. Refer to the CON-

SULT Immobilizer mode and follow the on-screen instructions.

>> Inspection End.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B26F7

BCM

Inside key antenna output circuit in BCM is malfunctioning. BCM

 

 

 

 

 

 

 

Content   ..  705  706  707  708   ..