Nissan Versa Note. Manual - part 705

 

  Index      Nissan     Nissan Versa Note (2014 year) - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  703  704  705  706   ..

 

 

Nissan Versa Note. Manual - part 705

 

 

B261F ASCD CLUTCH SWITCH

SEC-99

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

B261F ASCD CLUTCH SWITCH

DTC Logic

INFOID:0000000009705905

DTC DETECTION LOGIC

NOTE:

• If DTC B261F is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to

BCS-60, "DTC Logic"

.

• If DTC B261F is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to

BCS-61, "DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Start the engine.

2. Drive vehicle at a speed of 40 km/h (24.8 MPH) or more for 10 seconds.

3. Decrease the vehicle speed to below 40 km/h (24.8 MPH).

4. Repeat steps 2 and 3 twice (total of 3 times).

5. Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.
Is DTC detected?

YES >> Go 

to 

SEC-99, "Diagnosis Procedure"

.

NO

>> Inspection End

Diagnosis Procedure

INFOID:0000000009705906

Regarding Wiring Diagram information, refer to 

SEC-40, "Wiring Diagram"

.

1.

CHECK DTC OF COMBINATION METER

Check DTC in “Self Diagnostic Result” mode of “METER/M&A” using CONSULT.

Refer to 

MWI-21, "DTC Index"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CHECK FUSE

1. Turn power switch OFF.

2. Check that the following fuse in the fuse block (J/B) is not blown.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace the blown fuse after repairing the cause of blowing.

DTC No.

CONSULT screen items

(Trouble diagnosis content)

DTC detecting condition

Possible cause

B261F

ASCD CNCL/CLTCH SW
(ASCD clutch interlock 
switch)

BCM detects the following status for 10 seconds 
3 times
• Clutch interlock switch input: 0 V
• Vehicle speed: 40 km/h (24.8 MPH) or more

• Harness or connectors.

(CAN communication line is open 
or shorted.)

• Harness or connectors.

(Clutch interlock switch circuit is 
open or shorted)

• Clutch interlock switch
• Combination meter
• BCM 

Signal name

Fuse No.

Ignition power supply

10 (10 A)

SEC-100

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

B261F ASCD CLUTCH SWITCH

3.

CHECK CLUTCH INTERLOCK SWITCH POWER SUPPLY

1. Disconnect clutch interlock switch connector.

2. Turn ignition switch ON.

3. Check voltage between clutch interlock switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK CLUTCH INTERLOCK SWITCH SIGNAL 

1. Connect clutch interlock switch connector.

2. Check voltage between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> GO TO 6.

5.

REPLACE BCM

1. Replace BCM. Refer to 

BCS-70, "Removal and Installation"

.

2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT. Refer to the CON-

SULT Immobilizer mode and follow the on-screen instructions.

>> Inspection End

6.

CHECK CLUTCH INTERLOCK SWITCH CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect BCM connector.

3. Check continuity between clutch interlock switch harness connector and BCM harness connector.

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Repair or replace harness.

7.

CHECK CLUTCH INTERLOCK SWITCH

Refer to 

SEC-101, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 8.

NO

>> Replace clutch interlock switch. Refer to 

CL-10, "Exploded View"

.

8.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-41, "Intermittent Incident"

.

(+)

(–)

Voltage (V)

(Approx.)

Clutch interlock switch

Connector

Terminal

E34

1

Ground

Battery voltage

(+)

(–)

Condition

Voltage

BCM

Connector

Terminal

M98

101

Ground

Clutch pedal

Released

6 – 16 V

Depressed

0 – 1.5 V

Clutch interlock switch

BCM

Continuity

Connector

Terminal

Connector

Terminal

E34

2

M98

101

Yes

B261F ASCD CLUTCH SWITCH

SEC-101

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

>> Inspection End

Component Inspection

INFOID:0000000009705907

1.

CHECK CLUTCH INTERLOCK SWITCH

1. Turn ignition switch OFF.

2. Disconnect clutch interlock switch connector.

3. Check continuity between clutch interlock switch terminals.

Is the inspection result normal?

YES

>> Inspection End

NO

>> Replace clutch interlock switch. Refer to 

CL-10, "Exploded View"

.

Clutch interlock switch

Condition

Continuity

Terminal

1

2

Clutch pedal

Not depressed

No

Depressed

Yes

SEC-102

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

B2620 PARK/NEUTRAL POSITION SWITCH

B2620 PARK/NEUTRAL POSITION SWITCH

DTC Logic

INFOID:0000000009705908

NOTE:

• If DTC B2620 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to

BCS-60, "DTC Logic"

.

• If DTC B2620 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to

BCS-61, "DTC Logic"

.

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Start the engine.

2. Drive vehicle at a speed of 40 km/h (24.8 MPH) or more for 10 seconds.

3. Decrease the vehicle speed to below 40 km/h (24.8 MPH).

4. Repeat steps 2 and 3 twice (total of 3 times).

5. Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.
Is DTC detected?

YES >> Go 

to 

SEC-102, "Diagnosis Procedure"

.

NO

>> Inspection End

Diagnosis Procedure

INFOID:0000000009705909

Regarding Wiring Diagram information, refer to 

SEC-40, "Wiring Diagram"

.

1.

CHECK DTC OF COMBINATION METER

Check DTC in “Self Diagnostic Result” mode of “METER/M&A” using CONSULT.

Refer to 

MWI-21, "DTC Index"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CHECK FUSE

1. Turn power switch OFF.

2. Check that the following fuse in the fuse block (J/B) is not blown.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace the blown fuse after repairing the cause of blowing.

DTC No.

CONSULT screen items

(Trouble diagnosis content)

DTC detecting condition

Possible cause

B2620

NEUTRAL SW
(Neutral switch)

BCM detects the following status for 10 sec-
onds 3 times
• Park/neutral position switch input: Battery 

voltage

• Vehicle speed: 40 km/h (24.8 MPH) or more

• Harness or connector

(CAN communication line is open 
or shorted.)

• Harness or connector

(Park/neutral position switch circuit 
is open or shorted)

• Park/neutral position switch
• Combination meter
• BCM

Signal name

Fuse No.

Ignition power supply

3 (10 A)

 

 

 

 

 

 

 

Content   ..  703  704  705  706   ..