Content .. 617 618 619 620 ..

Nissan Rogue. Manual - part 619

B20D4 TAIL LAMP LH POWER SUPPLY CIRCUIT

EXL-105

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN HEADLAMP]

EXL

B20D4 TAIL LAMP LH POWER SUPPLY CIRCUIT

DTC Logic

INFOID:0000000011280764

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CHECK SELF DIAGNOSTIC RESULT

With

CONSULT.

1. Turn ignition switch ON.

2. Perform “Self Diagnostic Result”.
Is DTC B20D4 detected?

YES

>> Proceed to diagnosis procedure. Refer to

EXL-105, "Diagnosis Procedure"

>> Inspection End.

Diagnosis Procedure

INFOID:0000000011280765

CHECK TAIL LAMP SHORT CIRCUIT TO GROUND

1. Disconnect rear combination lamp (LH), license plate lamps, back up lamp connectors and IPDM E/R

connector.

2. Check continuity between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace harness.

CHECK TAIL LAMP SHORT CIRCUIT TO GROUND

1. Reconnect IPDM E/R connector.

2. Check continuity between rear combination lamp harness connector and ground.

Is the inspection result normal?

YES

>> Refer to

GI-44, "Intermittent Incident"

>> Replace IPDM E/R. Refer to

PCS-40, "Removal and Installation"

DTC

Display Item

Malfunction detected condition

Possible causes

B20D4

TAIL LAMP LH PWR SPLY CIRC

[CIRC SHORT TO GRND]

Short to ground

• IPDM E/R
• Short to ground

IPDM E/R

Ground

Continuity

Connector

Terminal

E119

Rear combination lamp

Ground

Continuity

Connector

Terminal

B90

EXL-106

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN HEADLAMP]

B20D5 TAIL LAMP RH POWER SUPPLY CIRCUIT

B20D5 TAIL LAMP RH POWER SUPPLY CIRCUIT

DTC Logic

INFOID:0000000011280766

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CHECK SELF DIAGNOSTIC RESULT

With

CONSULT.

1. Turn ignition switch ON.

2. Perform “Self Diagnostic Result”.
Is DTC B20D5 detected?

YES

>> Proceed to diagnosis procedure. Refer to

EXL-106, "Diagnosis Procedure"

>> Inspection End.

Diagnosis Procedure

INFOID:0000000011280767

CHECK TAIL LAMP SHORT CIRCUIT TO GROUND

1. Disconnect rear combination lamp (RH), back up lamp connectors and IPDM E/R connector.

2. Check continuity between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace harness.

CHECK TAIL LAMP SHORT CIRCUIT TO GROUND

1. Reconnect IPDM E/R connector.

2. Check continuity between rear combination lamp harness connector and ground.

Is the inspection result normal?

YES

>> Refer to

GI-44, "Intermittent Incident"

>> Replace IPDM E/R. Refer to

PCS-40, "Removal and Installation"

DTC

Display Item

Malfunction detected condition

Possible causes

B20D5

TAIL LAMP RH PWR SPLY CIRC
[CIRC SHORT TO GRND]

When a short circuit to ground is detected in
the tail lamp supply voltage circuit.

• IPDM E/R
• Short to ground

IPDM E/R

Ground

Continuity

Connector

Terminal

E119

Rear combination lamp

Ground

Continuity

Connector

Terminal

B102

EXTERIOR LIGHTING SYSTEM SYMPTOMS

EXL-107

< SYMPTOM DIAGNOSIS >

[HALOGEN HEADLAMP]

EXL

SYMPTOM DIAGNOSIS

EXTERIOR LIGHTING SYSTEM SYMPTOMS

Symptom Table

INFOID:0000000011280768

CAUTION:

Perform the “Self Diagnostic Result” with CONSULT before the symptom diagnosis. Perform the trou-

ble diagnosis if any DTC is detected.

Symptom

Possible cause

Inspection item

Headlamp (HI) is not
turned ON.

One side

• Fuse
• Halogen bulb (HI)
• Harness between IPDM E/R

and headlamp (HI)

• Harness between headlamp

(HI) and ground

• IPDM E/R

Headlamp (HI) circuit
Refer to

Both sides

Symptom diagnosis
“BOTH SIDE HEADLAMPS (HI)
ARE NOT TURNED ON”
Refer to

EXL-100, "DTC Logic"

(LH) or

EXL-101, "DTC Logic"

(RH).

High beam indicator lamp is not turned ON.
[Headlamp (HI) is turned ON.]

Combination meter

• Combination meter

“Data Monitor” “HI-BEAM IND”

• BCM (HEAD LAMP)

“Active Test” “HEADLAMP”

Headlamp (LO) is not
turned ON.

One side

• Fuse
• Halogen bulb (LO)
• Harness between IPDM E/R

and headlamp lamp (LO)

• Harness between headlamp

(LO) and ground

• IPDM E/R

Headlamp (LO) circuit
Refer to

EXL-102, "DTC Logic"

(LH)

EXL-103, "DTC Logic"

(RH).

Both sides

Symptom diagnosis
“BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON”
Refer to

EXL-102, "DTC Logic"

(LH) or

EXL-103, "DTC Logic"

(RH).

Each lamp is not turned ON/OFF with lighting switch
AUTO.

• Combination switch
• Harness between combination

switch and BCM

• BCM

Combination switch
Refer to

BCS-73, "Symptom Table"

(with Intelligent Key system) or

BCS-133, "Symptom Table"

(with-

out Intelligent Key system).

• Optical sensor
• Harness between optical sen-

sor and BCM

• BCM

Optical sensor
Refer to

EXL-87, "Component

Function Check"

Daytime running light is not turned ON.
[Headlamp (HI) is turned ON.]

• Fuse
• Harness between IPDM E/R

and front combination lamp

• IPDM E/R
• BCM
• ECM
• Combination meter

• Daytime running light circuit

Refer to

EXL-97, "DTC Logic"

• BCM (HEADLAMP)

“Data Monitor” “ENGINE STATE”

• Combination meter

“Data Monitor” “PKB SW”

• BCM (HEADLAMP)

“Active Test” “DAYTIME RUN-
NING LIGHT”

Parking lamp is not turned ON.

• Fuse
• Parking lamp bulb
• Harness between IPDM E/R

and front combination lamp

• IPDM E/R

Parking lamp circuit
Refer to

EXL-104, "DTC Logic"

EXL-108

< SYMPTOM DIAGNOSIS >

[HALOGEN HEADLAMP]

EXTERIOR LIGHTING SYSTEM SYMPTOMS

Front side marker lamp is not turned ON.

• Front side marker lamp bulb
• Harness between IPDM E/R

and front side marker lamp

• Harness between front side

marker lamp and ground

• IPDM E/R

Front side marker lamp circuit
Refer to

EXL-104, "DTC Logic"

License plate lamp is not turned ON.

• License plate lamp bulb
• Harness between IPDM E/R

and license plate lamp

• Harness between license plate

lamp and ground

License plate lamp circuit
Refer to

EXL-105, "DTC Logic"

Parking lamp, side marker lamp, tail lamp and li-
cense plate lamp are not turned ON.

Symptom diagnosis
“PARKING, SIDE MARKER, LICENSE PLATE AND TAIL LAMPS ARE
NOT TURNED ON”
Refer to

EXL-104, "DTC Logic"

Tail lamp indicator is not turned ON.
(Exterior lamps are turned ON.)

Combination meter

• Combination meter

“Data Monitor” “LIGHT IND”

• BCM (HEADLAMP)

“Active Test” “TAIL LAMP”

Turn signal lamp does not
blink.

Indicator lamp is nor-
mal.
(Applicable side per-
forms high flasher acti-
vation.)

• Turn signal lamp bulb
• Door mirror
• Harness between BCM and

each turn signal lamp

• Harness between each turn sig-

nal lamp and ground

Turn signal lamp circuit
Refer to

EXL-92, "Component

Function Check"

Turn signal indicator lamp
does not blink.
(Turn signal lamp is nor-
mal.)

One side

Combination meter

—

Both sides
(Always)

• Turn signal indicator lamp sig-

nal

• BCM
• Combination meter

• Combination meter

“Data Monitor” “TURN IND”

• BCM (FLASHER)

“Active Test” “FLASHER”

Both sides
(Only when activating
hazard warning lamp
with ignition switch
OFF)

• Combination meter power sup-

ply and ground circuit

• Combination meter

Combination meter
Power supply and ground circuit
Refer to

MWI-60, "COMBINATION

METER : Diagnosis Procedure"

• Hazard warning lamp does not activate.
• Hazard warning lamp continues activating.
(Turn signal is normal.)

• Hazard switch
• Harness between hazard

switch and BCM

• Harness between hazard

switch and ground

• BCM

Hazard switch circuit
Refer to

EXL-90, "Component

Function Check"

Front fog lamp is not
turned ON.

One side

• Front fog lamp bulb
• Harness between IPDM E/R

and front fog lamp

• Harness between front fog lamp

and ground

• IPDM E/R

Front fog lamp circuit
Refer to

EXL-96, "DTC Logic"

(LH)

EXL-98, "DTC Logic"

(RH).

Both sides

Symptom diagnosis
“BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON”
Refer to

EXL-96, "DTC Logic"

(LH) or

EXL-98, "DTC Logic"

(RH).

Symptom

Possible cause

Inspection item

Content .. 617 618 619 620 ..