Nissan Rogue. Manual - part 404

DLN-60

< DTC/CIRCUIT DIAGNOSIS >

[TRANSFER: TY21C]

POWER SUPPLY AND GROUND CIRCUIT

2. Check the 10A fuse (#6).

3. Disconnect fuse block (J/B) harness connector.

4. Check the continuity between AWD control unit harness connector and fuse block (J/B) harness connec-

tor.

5. Check the continuity between AWD control unit harness connector and the ground.

Is the inspection result normal?

YES

>> Perform the trouble diagnosis for power supply circuit. Refer to 

PG-13, "Wiring Diagram — Bat-

tery Power Supply —"

.

NO

>> Repair or replace error-detected parts.

7.

CHECK AWD CONTROL UNIT GROUND

1. Turn the ignition switch OFF.

2. Check the continuity between AWD control unit harness connector and ground.

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Repair or replace error-detected parts.

AWD control unit

Fuse block (J/B)

Continuity

Connector

Terminal

Connector

Terminal

B75

9

M68

15R

Yes

AWD control unit

—

Continuity

Connector

Terminal

B75

9

Ground

No

AWD control unit

—

Continuity

Connector

Terminal

B75

10

Ground

Yes

11

HEAVY TIGHT-CORNER BRAKING SYMPTOM OCCURS

DLN-61

< SYMPTOM DIAGNOSIS >

[TRANSFER: TY21C]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

SYMPTOM DIAGNOSIS

HEAVY TIGHT-CORNER BRAKING SYMPTOM OCCURS

Description

INFOID:0000000011278347

Heavy tight-corner braking symptom occurs when the vehicle is driven and the steering wheel is turned fully to

either side after the engine is started.

NOTE:

Light tight-corner braking symptom may occur depending on driving conditions. This is not malfunction.

Diagnosis Procedure

INFOID:0000000011278348

1.

PERFORM ECM SELF DIAGNOSTIC RESULT

 With CONSULT

Perform “Self Diagnostic Result” of “ENGINE”.
Is any DTC detected?

YES

>> Check the DTC. Refer to 

EC-96, "DTC Index"

.

NO

>> GO TO 2.

2.

PERFORM SELF DIAGNOSTIC RESULT

 With CONSULT

Perform “Self Diagnostic Result” of “ALL MODE AWD/4WD”.
Is DTC “U1000” detected?

YES

>> Proceed to 

DLN-56, "Diagnosis Procedure"

.

NO

>> GO TO 3.

3.

CHECK AWD SOLENOID

Perform the trouble diagnosis of the AWD solenoid. Refer to 

DLN-38, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace the error-detected parts.

4.

CHECK ELECTRIC CONTROLLED COUPLING

1. Turn the ignition switch OFF.

2. Set the transaxle to neutral. Release the parking brake.

3. Lift up the vehicle.

4. Rotate the propeller shaft by hand.

5. Hold rear wheel of right and left lightly.
Does rear wheel rotate?

YES

>> Replace electric controlled coupling for mechanical malfunction (clutch sticking etc.). Refer to

DLN-115, "Removal and Installation"

.

NO

>> Check each harness connector pin terminal for disconnection.

DLN-62

< SYMPTOM DIAGNOSIS >

[TRANSFER: TY21C]

VEHICLE DOES NOT ENTER AWD MODE

VEHICLE DOES NOT ENTER AWD MODE

Description

INFOID:0000000011278349

Vehicle does not enter 4-wheel drive mode even though AWD warning is not displayed.

Diagnosis Procedure

INFOID:0000000011278350

1.

CHECK INFORMATION DISPLAY (COMBINATION METER)

Perform the trouble diagnosis of combination meter. Refer to 

MWI-53, "Work flow"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the error-detected parts.

2.

CHECK PARKING BRAKE SWITCH SIGNAL

 With CONSULT

Check “PARKING BRAKE SW SIG” in “Data Monitor” for “ALL MODE AWD/4WD”.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Proceed to 

BRC-113, "Component Function Check"

.

3.

CRUISE TEST

Drive the vehicle for a period of time.
Does any symptom occur?

YES

>> Replace electric controlled coupling for mechanical malfunction (mechanical engagement of

clutch is not possible). Refer to 

DLN-115, "Removal and Installation"

.

NO

>> Check each harness connector pin terminal for disconnection.

Monitor Item

Condition

Status

PARKING BRAKE SW SIG

When the parking brake pedal is operation.

On

When the parking brake pedal is not operation.

Off

AWD HIGH TEMP IS DISPLAYED ON INFORMATION DISPLAY

DLN-63

< SYMPTOM DIAGNOSIS >

[TRANSFER: TY21C]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

AWD HIGH TEMP IS DISPLAYED ON INFORMATION DISPLAY

Description

INFOID:0000000011278351

While driving, AWD warning (AWD High Temp. Stop vehicle) is displayed on information display (combination

meter).

• This symptom protects drivetrain parts when a heavy load is applied to the electric controlled coupling and

multiple disc clutch temperature increases. Also, optional distribution of torque sometimes becomes rigid

before AWD warning (AWD High Temp. Stop vehicle) is displayed. Both cases are not malfunction. Refer to

DLN-22, "Protection Function"

.

• When this symptom occurs, stop vehicle and allow it to idle for some times. Displays will stop and system

will be restored.