Nissan Rogue. Manual - part 1241

WT-40

< DTC/CIRCUIT DIAGNOSIS >

C1730, C1731, C1732, C1733 FLAT TIRE

3.

CHECK TIRE PRESSURE SIGNAL

 With CONSULT

1. Adjust tire pressure for all wheels to the specified value. Refer to 

WT-73, "Tire Air Pressure"

. 

2. Select “Data Monitor” in “AIR PRESSURE MONITOR”.

3. Check that the air pressures match the specified value.

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Repair or replace malfunctioning components.

Monitor item

Displayed value

AIR PRESS FL

Approximately equal to value indicated on tire gauge for front LH tire

AIR PRESS FR

Approximately equal to value indicated on tire gauge for front RH tire

AIR PRESS RR

Approximately equal to value indicated on tire gauge for rear RH tire

AIR PRESS RL

Approximately equal to value indicated on tire gauge for rear LH tire

C1734 BCM

WT-41

< DTC/CIRCUIT DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

C1734 BCM

DTC Logic

INFOID:0000000011280514

NOTE:

The Signal Tech II Tool [– (J-50190)] can be used to perform the following functions. Refer to the Signal Tech

II User Guide for additional information.

• Activate and display TPMS sensor IDs

• Display tire pressure reported by the TPMS sensor

• Read TPMS DTCs

• Register TPMS sensor IDs

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PERFORM SELF DIAGNOSTIC RESULT 

 With CONSULT

Perform “Self Diagnostic Result”.
Is DTC C1734 detected?

YES

>> Proceed to 

WT-41, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000011280515

NOTE:

The Signal Tech II Tool [– (J-50190)] can be used to perform the following functions. Refer to the Signal Tech

II User Guide for additional information.

• Activate and display TPMS sensor IDs

• Display tire pressure reported by the TPMS sensor

• Read TPMS DTCs

• Register TPMS sensor IDs

Regarding Wiring Diagram information, refer to 

WT-19, "Wiring Diagram"

.

1.

CHECK BCM HARNESS CONNECTORS

Check BCM harness connectors for damage or loose connections.
Is the inspection result normal?

YES

>> Repair or replace connectors.

NO

>> GO TO 2.

2.

CHECK BCM POWER SUPPLY AND GROUND

Check BCM power supply and ground. Refer to 

BCS-68, "Diagnosis Procedure"

 (with Intelligent Key system)

or 

BCS-128, "Diagnosis Procedure"

 (without Intelligent Key system).

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness or connectors.

3.

CHECK BCM INPUT/OUTPUT SIGNALS

Check BCM input/output signals. Refer to 

BCS-28, "Reference Value"

 (with Intelligent Key system) or 

BCS-96,

"Reference Value"

 (without Intelligent Key system).

Is the inspection result normal?

YES

>> Inspection End.

DTC

Display Item

Malfunction Detected Condition

Possible Cause

C1734

CONTROL UNIT

TPMS malfunction in BCM.

BCM

WT-42

< DTC/CIRCUIT DIAGNOSIS >

C1734 BCM

NO

>> Replace BCM. Refer to 

BCS-75, "Removal and Installation"

 (with Intelligent Key system) or 

BCS-

135, "Removal and Installation"

 (without Intelligent Key system).

C1735 IGNITION SIGNAL

WT-43

< DTC/CIRCUIT DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

C1735 IGNITION SIGNAL

DTC Logic

INFOID:0000000011280516

NOTE:

The Signal Tech II Tool [– (J-50190)] can be used to perform the following functions. Refer to the Signal Tech

II User Guide for additional information.

• Activate and display TPMS sensor IDs

• Display tire pressure reported by the TPMS sensor

• Read TPMS DTCs

• Register TPMS sensor IDs

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PERFORM SELF DIAGNOSTIC RESULT 

 With CONSULT

Perform “Self Diagnostic Result”.
Is DTC C1735 detected?

YES

>> Proceed to 

WT-43, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000011280517

NOTE:

The Signal Tech II Tool [– (J-50190)] can be used to perform the following functions. Refer to the Signal Tech

II User Guide for additional information.

• Activate and display TPMS sensor IDs

• Display tire pressure reported by the TPMS sensor

• Read TPMS DTCs

• Register TPMS sensor IDs

1.

PERFORM BCM SELF-DIAGNOSIS

When DTC “C1735-00” is detected, perform BCM diagnosis.

>> Perform BCM diagnosis. Refer to 

BCS-47, "DTC Index"

 (with Intelligent Key system) or 

BCS-108,

"DTC Index"

 (without Intelligent Key system).

DTC

Display Item

Malfunction Detected Condition

Possible Cause

C1735

IGNITION SIGNAL LINE - BCM/
TPMS

BCM has detected a mismatch between 
IGN ON signals.

BCM