Nissan Rogue. Manual - part 1239

WT-32

< DTC/CIRCUIT DIAGNOSIS >

C1704, C1705, C1706, C1707 LOW TIRE PRESSURE

YES

>> Perform DTC CONFIRMATION PROCEDURE again. Refer to 

WT-31, "DTC Logic"

.

NO

>> GO TO 3.

3.

CHECK TIRE PRESSURE SIGNAL

 With CONSULT

1. Adjust tire pressure for all wheels to the specified value. Refer to 

WT-73, "Tire Air Pressure"

. 

2. Select “Data Monitor” in “AIR PRESSURE MONITOR”.

3. Check that the air pressures match the specified value.

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Repair or replace malfunctioning components.

Monitor item

Displayed value

AIR PRESS FL

Approximately equal to value indicated on tire gauge for front LH tire

AIR PRESS FR

Approximately equal to value indicated on tire gauge for front RH tire

AIR PRESS RR

Approximately equal to value indicated on tire gauge for rear RH tire

AIR PRESS RL

Approximately equal to value indicated on tire gauge for rear LH tire

C1708, C1709, C1710, C1711 TRANSMITTER (NO DATA)

WT-33

< DTC/CIRCUIT DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

C1708, C1709, C1710, C1711 TRANSMITTER (NO DATA)

DTC Logic

INFOID:0000000011280506

NOTE:

The Signal Tech II Tool [– (J-50190)] can be used to perform the following functions. Refer to the Signal Tech

II User Guide for additional information.

• Activate and display TPMS sensor IDs

• Display tire pressure reported by the TPMS sensor

• Read TPMS DTCs

• Register TPMS sensor IDs

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PERFORM SELF DIAGNOSTIC RESULT 

 With CONSULT

1. Perform tire pressure sensor ID registration. Refer to 

WT-26, "Work Procedure"

.

2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for

10 minutes.

NOTE:

Avoid driving in areas with radio interference.

3. Perform “Self Diagnostic Result”.
Is DTC C1708, C1709, C1710, or C1711 detected?

YES

>> Proceed to 

WT-33, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000011280507

NOTE:

The Signal Tech II Tool [– (J-50190)] can be used to perform the following functions. Refer to the Signal Tech

II User Guide for additional information.

• Activate and display TPMS sensor IDs

• Display tire pressure reported by the TPMS sensor

• Read TPMS DTCs

• Register TPMS sensor IDs

Regarding Wiring Diagram information, refer to 

WT-19, "Wiring Diagram"

.

1.

CHECK TIRE PRESSURE SIGNAL

 With CONSULT

1. Select “Data Monitor” in “AIR PRESSURE MONITOR”.

2. Check that the air pressures match the specified value.

DTC

Display Item

Malfunction Detected Condition

Possible Cause

C1708

[NO - DATA] - FL

Data signal from the front LH wheel tire pres-
sure sensor cannot be detected.

• Driving in area with radio interference.
• ID registration incomplete
• Tire pressure sensor
• Harness or connectors
• BCM

C1709

[NO - DATA] - FR

Data signal from the front RH wheel tire pres-
sure sensor cannot be detected.

C1710

[NO - DATA] - RR

Data signal from the rear RH wheel tire pres-
sure sensor cannot be detected.

C1711

[NO - DATA] - RL

Data signal from the rear LH wheel tire pres-
sure sensor cannot be detected.

WT-34

< DTC/CIRCUIT DIAGNOSIS >

C1708, C1709, C1710, C1711 TRANSMITTER (NO DATA)

Are all tire pressures displayed 0 kPa (psi)?

YES

>> GO TO 2.

NO

>> Replace applicable tire pressure sensor. Refer to 

WT-68, "Removal and Installation"

.

2.

CHECK BCM POWER CIRCUIT

Check voltage between BCM connector M20 terminal 161 and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness or connectors.

3.

CHECK BCM GROUND CIRCUIT

Check continuity between BCM connector M20 and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness or connectors.

4.

TIRE PRESSURE SENSOR ID REGISTRATION

Perform tire pressure sensor ID registration. Refer to 

WT-26, "Work Procedure"

.

Can the tire pressure sensor ID registration be completed?

YES

>> GO TO 5.

NO

>> Replace applicable tire pressure sensor. Refer to 

WT-68, "Removal and Installation"

.

5.

RECHECK TIRE PRESSURE SIGNAL

 With CONSULT

1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for

10 minutes.

2. Select “Data Monitor” in “AIR PRESSURE MONITOR”.

3. Check that the air pressures match the specified value.

Does Data Monitor display specified value without turning tire pressure warning lamp ON?

YES

>> Inspection End.

Monitor item

Displayed value

AIR PRESS FL

Approximately equal to specified value. Refer to 

WT-73, "Tire Air Pressure"

.

AIR PRESS FR

AIR PRESS RR

AIR PRESS RL

BCM

Ground

Voltage

(Approx.)

Connector

Terminal

M20

161

—

Battery voltage

BCM

Ground

Continuity

Connector

Terminal

M20

170

—

Yes

171

Monitor item

Displayed value

AIR PRESS FL

Approximately equal to specified value. Refer to 

WT-73, "Tire Air Pressure"

.

AIR PRESS FR

AIR PRESS RR

AIR PRESS RL

C1708, C1709, C1710, C1711 TRANSMITTER (NO DATA)

WT-35

< DTC/CIRCUIT DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

NO

>> Replace BCM. Refer to 

BCS-75, "Removal and Installation"

 (with Intelligent Key system) or 

BCS-

135, "Removal and Installation"

 (without Intelligent Key system).