Nissan Rogue. Manual - part 1242

WT-44

< DTC/CIRCUIT DIAGNOSIS >

C1765, C1766, C1767, C1768 TIRE PRESSURE SENSOR

C1765, C1766, C1767, C1768 TIRE PRESSURE SENSOR

DTC Logic

INFOID:0000000011280518

DTC DETECTION LOGIC

Diagnosis Procedure

INFOID:0000000011280519

1.

PERFORM ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS

When DTC “C1765, C1766, C1767, C1768” is detected, perform ABS system diagnosis.

>> Perform ABS system diagnosis. Refer to 

BRC-53, "DTC Index"

.

DTC

Display Item 

Malfunction Detected Condition

Possible Cause

C1765

WHEEL TOP DATA FL
(Wheel top data front left)

Malfunction in the wheel top data from the front LH 
wheel speed sensor.

Wheel speed sensor 

C1766

WHEEL TOP DATA FR
(Wheel top data front right)

Malfunction in the wheel top data from the front RH 
wheel speed sensor.

C1767

WHEEL TOP DATA RR
(Wheel top data rear right)

Malfunction in the wheel top data from the rear RH 
wheel speed sensor.

C1768

WHEEL TOP DATA RL
(Wheel top data rear left)

Malfunction in the wheel top data from the rear LH 
wheel speed sensor.

C1769 CONFIGURATION SETTING

WT-45

< DTC/CIRCUIT DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

C1769 CONFIGURATION SETTING

DTC Logic

INFOID:0000000011280520

This procedure must be performed:

• After replacement of BCM.

DTC DETECTION LOGIC

Diagnosis Procedure

INFOID:0000000011280521

1.

TIRE PRESSURE MONITORING SYSTEM CONFIGURATION

Perform configuration. Refer to 

WT-29, "Work Procedure"

.

>> GO TO 2.

2.

TIRE PRESSURE SENSOR ID REGISTRATION 

Perform tire pressure sensor ID registration. Refer to 

WT-26, "Work Procedure"

.

Does low tire pressure warning lamp turn OFF?

YES

>> Inspection End.

NO

>> Replace BCM. Refer to 

BCS-75, "Removal and Installation"

 (with Intelligent Key system) or 

BCS-

135, "Removal and Installation"

 (without Intelligent Key system).

DTC

Display Item

Malfunction detected condition

C1769

CONFIG SETTING
(Configuration setting)

Tire air pressure monitoring system configuration cannot be performed.

Receiver ID registration cannot be performed.

WT-46

< DTC/CIRCUIT DIAGNOSIS >

C1770, C1771, C1772, C1773 G SENSOR

C1770, C1771, C1772, C1773 G SENSOR

DTC Logic

INFOID:0000000011280522

DTC DETECTION LOGIC

Diagnosis Procedure

INFOID:0000000011280523

1.

REPLACE WHEEL TIRE PRESSURE SENSOR

When DTC “C1770, C1771, C1772, C1773” is detected, replace wheel tire pressure sensor.

>> Replace applicable wheel tire pressure sensor. Refer to 

WT-68, "Removal and Installation"

.

DTC

Display Item

Malfunction Detected Condition

Possible Causes

C1770

G SENSOR FL
(G sensor front left)

Malfunction in the G sensor data from front left wheel sensor.

• Tire pressure sensor
• Tire pressure receiver

C1771

G SENSOR FR
(G sensor front right)

Malfunction in the G sensor data from front right wheel sensor.

C1772

G SENSOR RL
(G sensor rear left)

Malfunction in the G sensor data from rear left wheel sensor.

C1773

G SENSOR RR
(G sensor rear right)

Malfunction in the G sensor data from rear right wheel sensor.

U1000 CAN COMM CIRCUIT

WT-47

< DTC/CIRCUIT DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

U1000 CAN COMM CIRCUIT

Description

INFOID:0000000011280524

CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-

tiplex communication line with high data communication speed and excellent error detection ability. Many elec-

tronic control units are equipped onto a vehicle, and each control unit shares information and links with other

control units during operation (not independent). In CAN communication, control units are connected with 2

communication lines (CAN-H line, CAN-L line) allowing a high rate of information transmission with less wiring.

Each control unit communicates data but selectively reads required data only.

DTC Logic

INFOID:0000000011280525

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION

 With CONSULT

1. Drive for several minutes at a speed of 40 km/h (25 MPH) or more.

2. Stop the vehicle.

3. Perform “Self Diagnostic Result” for “AIR PRESSURE MONITOR”.
Is DTC “U1000” detected?

YES

>> Proceed to 

WT-47, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000011280526

Proceed to 

LAN-30, "CAN COMMUNICATION SYSTEM : CAN System Specification Chart"

.

DTC

Display item

Malfunction detected condition

Possible cause

U1000

CAN COMM CIRCUIT

BCM is not communicating CAN com-
munication signal for 2 seconds or more.

• CAN communication malfunction
• Malfunction of BCM