Nissan Altima HL32 Hybrid. Manual - part 1078

TM-30

< ON-VEHICLE REPAIR >

[HYBRID TRANSAXLE: RE0F01H]

CONTROL CABLE

• When installing the control cable to the control device assembly, make sure that the control cable socket is

fully pressed into the control device assembly, and the control cable end is fully pressed in with the ribbed

surface facing upward.

• After installation is complete, adjust and check the transaxle position. Refer to 

TM-26, "Inspection and

Adjustment"

.

Inspection and Adjustment

INFOID:0000000004212390

INSPECTION

1. Place selector lever in “P” position, and turn ignition switch ON (engine stop).
2. Make sure that selector lever can be shifted to other than “P” position when brake pedal is depressed.

Also make sure that selector lever can be shifted from “P” position only when brake pedal is depressed.

3. Move the selector lever and check for excessive effort, sticking, noise or rattle.
4. Confirm the selector lever stops at each position with the feel of engagement when it is moved through all

the positions. Check that the actual position of the selector lever matches the position shown by the shift

position indicator and the manual lever on the transaxle.

5. The method of operating the selector lever to individual posi-

tions correctly should be as shown.

• (A): Press selector button to operate selector lever, while

depressing the brake pedal.

• (B): Press selector button to operate selector lever.

• (C): Selector lever can be operated without pressing selector

button.

6. Press the selector button in the “P”, “R”, and “N” positions with-

out applying forward/backward force to selector lever, check but-

ton operation for sticking.

7. Confirm the back-up lamps illuminate only when selector lever is

placed in the “R” position. Confirm the back-up lamps do not illu-

minate when the selector lever is pushed toward the “R” position when in the “P” or “N” position.

8. Confirm the hybrid system can only be started with the selector lever in the “P” position.
9. Make sure transaxle is locked completely in “P” position.

ADJUSTMENT

CAUTION:

Apply parking brake before adjustment.
1. Loosen the control cable nut.
2. Place the manual lever and the selector lever in “P” position.
3. Tighten control cable nut to specified torque.

CAUTION:

Secure the manual lever when tightening control cable nut. Make sure the manual lever stays in

the "P" position.

4. Check the operation of the transaxle. Refer to 

TM-28, "Inspection and Adjustment"

.

ALDIA0058GB

Control cable nut: Refer to 

TM-29, "Exploded View"

.

DIFFERENTIAL SIDE OIL SEAL

TM-31

< ON-VEHICLE REPAIR >

[HYBRID TRANSAXLE: RE0F01H]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

DIFFERENTIAL SIDE OIL SEAL

Exploded View

INFOID:0000000004212391

Removal and Installation

INFOID:0000000004212392

REMOVAL

1. Remove the drive shaft. Refer to 

FAX-11, "Removal and Installation (Left Side)"

 and 

FAX-12, "Removal

and Installation (Right Side)"

.

2. Remove the differential side oil seal from the transaxle assembly using suitable tool.

CAUTION:

Do not scratch transaxle assembly.

INSTALLATION

1. Drive the new differential side oil seal to the transaxle assembly until it is flush using suitable tool.

CAUTION:

• Do not reuse differential side oil seals.

• Apply specified transaxle fluid to the differential side oil seals.

2. Install the drive shaft. Refer to 

FAX-11, "Removal and Installation (Left Side)"

 and 

FAX-12, "Removal and

Installation (Right Side)"

.

3. Check the transaxle fluid level. Refer to 

TM-24, "Inspection"

.

1.

Transaxle assembly

2.

Differential side oil seal

ALDIA0072ZZ

Oil seal depth : 0

±0.5 mm (0 ± 0.02 in)

TM-32

< ON-VEHICLE REPAIR >

[HYBRID TRANSAXLE: RE0F01H]

PARK/NEUTRAL POSITION (PNP) SWITCH

PARK/NEUTRAL POSITION (PNP) SWITCH

Exploded View

INFOID:0000000004212393

Removal and Installation

INFOID:0000000004212394

CAUTION:

When replacing the PNP switch, replace the manual lever (1)

with new manual lever (1) or transfer the manual lever (1) from

the old PNP switch to the new PNP switch. The manual lever (1)

must have a rectangular hole as shown for proper operation of

the transaxle.

REMOVAL

1. Shift the control lever to the N (Neutral) position.
2. Remove the nut to disconnect the control cable from the manual lever on the PNP switch.
3. Remove the nut and remove the manual lever from the PNP switch.
4. Disconnect the PNP switch connector.
5. Remove the PNP switch bolts (A) and remove the PNP switch.

1.

Lock washer

2.

Manual lever

3.

Park neutral position (PNP) switch

4.

Transaxle assembly

AWDIA0044GB

JPDIA0483ZZ

ALDIA0089ZZ

PARK/NEUTRAL POSITION (PNP) SWITCH

TM-33

< ON-VEHICLE REPAIR >

[HYBRID TRANSAXLE: RE0F01H]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

INSTALLATION

Installation is in the reverse order of removal.

• Align the PNP switch position indicator (A) with the neutral position

line (B) when installing.

• After installation of the PNP switch, check the continuity of the PNP switch.

• After installation is complete, adjust and check the control lever position. Refer to 

TM-30, "Inspection and

Adjustment"

.

Inspection and Adjustment

INFOID:0000000004212395

INSPECTION

1. Shift the control lever to the "N" (Neutral) position.
2. Check position of PNP switch. The PNP switch position indicator

(A) should point to the neutral position line (B) on the PNP

switch as shown.

ADJUSTMENT

1. Put the control lever in the "N" position.
2. Loosen the PNP switch bolts (A).

ALDIA0087ZZ

ALDIA0087ZZ

ALDIA0089ZZ