Nissan Murano Z51. Manual - part 1191

 

  Главная      Nissan     Nissan Murano Z51 (2010 year) - Service Manual

 

поиск по сайту            

 

 

 

 

 

 

 

 

 

содержание   ..  1189  1190  1191  1192   ..

 

 

Nissan Murano Z51. Manual - part 1191

 

 

RF-104

< REMOVAL AND INSTALLATION >

SUNROOF UNIT ASSEMBLY

6.

Point matching marks on body  before removing the sunroof unit assembly.

7.

Apply protective tape around the roof panel to protect the surface from damage.

8.

Remove the front sunroof glass. Refer to 

RF-106, "Removal and Installation"

.

9.

Cut adhesive.
• Cut the adhesibe using windshield cutter (A).

• Pass piano wire though the adhesive with a wire pierce.
• Tie piano wire both ends to wire grip.
• Pull piano wire in turn and cut off adhesive.

10. Remove sunroof unit assembly from vehicle.

INSTALLATION

WARNING:

• Keep heat and open flames away as primers and adhesive are flammable.
• The materials contained in the kit are harmful if swallowed, and may irritate skin and eyes. Never let

them in contact with the skin and eyes.

• Use in an open, well ventilated location. Never breathe the vapors. They may be harmful if inhaled.

Move immediately to an area with fresh air if affected by vapor inhalation.

CAUTION:

After installing the sunroof unit assembly and glass lid, perform the leak test and check that there is
no malfunction.
NOTE:
• Use a genuine Nissan Urethane Adhesive Kit (if available) or an equivalent and follow the instructions fur-

nished with it.

• Inform the customer that the vehicle should remain stationary until the urethane adhesive has completely

cured (approximately 24 hours). Curing time varies with temperature and humidity.

1.

Using a knife or spatula, trim the adhesive (sealant) remaining
on body down to approximately 2 mm (0.08 in) thick (a) so that
the contour becomes smooth.

CAUTION:

If bonded area on body is scratched, be sure to repair it
with a 2-component urethane. Never use lacquer.

2.

Clean bonded area on sunroof frame with white gasoline.

3.

Apply paint primer along the entire circumference of sunroof frame.

CAUTION:

There are 2 types of primer. Never confuse the application methods.
Paint primer: for painted surfaces
Glass primer: for glass

4.

Apply paint primer on areas where adhesive contacts on the side of vehicle body.

CAUTION:

If paint primer adheres to a painted surface other than bonding area, or if it overflows, quickly
remove it with white gasoline.

PIIB3505J

JMKIA0307ZZ

SUNROOF UNIT ASSEMBLY

RF-105

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

L

M

A

B

RF

N

O

P

5.

After applying primers, apply the adhesive along the entire circumference of the sunroof unit assembly as
shown in the figure, and within the time specified in the instructions for the adhesive.
Open adhesive by cutting off the nozzle tip and set it in a sealant gun.

6.

Align mating marks on body and sunroof unit assembly. Install sunroof unit assembly to the body.

7.

Press entire surface of sunroof unit assembly lightly to fit it completely.

8.

Using a spatula, repair any adhesive overflow or shortage to make the surface smooth.

9.

Remove protective tape.

10. Temporarily tighten the mounting bolts and nuts to the of sunroof unit assembly.

11. Tighten the installation points diagonally excluding the installation point of the sunroof bracket around the

roof opening.

12. Tighten the mounting bolts and nuts to the sunroof bracket.

13. Connect drain hoses.
14. Install the glass lid. Refer to 

RF-95, "Removal and Installation"

.

NOTE:
After installation, carry out fitting adjustment.Refer to 

RF-96, "Adjustment"

.

15. Install the headlining. Refer to 

INT-30, "SUNROOF : Removal and Installation"

.

16. Check for water leaks.

NOTE:
• Perform the water leakage check more than 2 hours after sunroof unit assembly installation.
• After glass lid fitting adjustment, carry out water leakage check by spreading water in the whole roof.

Disassembly and Assembly

INFOID:0000000005516873

DISASSEMBLY

1.

Remove the wind deflector. Refer to 

RF-112, "Removal and Installation"

.

2.

Remove the front sunshade and rear sunshade. Refer to 

RF-114, "Removal and Installation"

.

ASSEMBLY

Assemble in the reverse order of disassembly.

RF-106

< REMOVAL AND INSTALLATION >

FRONT SUNROOF GLASS

FRONT SUNROOF GLASS

Exploded View

INFOID:0000000005516874

Removal and Installation

INFOID:0000000005516875

REMOVAL

1.

Remove the roof rail assembly. Refer to 

EXT-29, "Removal and Installation"

.

2.

Remove the roof side finisher. Refer to 

RF-95, "Removal and Installation"

.

3.

Fully open the glass lid.

4.

Paint matching marks on body before removeing the front sunroof glass.

5.

Apply protective tape around the roof panel and front sunroof glass to protect the surface from damage.

1.

Front sunroof glass

2.

Adhesive

3.

Windshield glass

4.

Sunroof frame

5.

Primer

6.

Weather-strip

Refer to 

GI-4, "Components"

 for symbols in the figure.

JMKIA1899GB

FRONT SUNROOF GLASS

RF-107

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

L

M

A

B

RF

N

O

P

6.

Remove weather-strip.

7.

Cut adhesive.
• Pass piano wire though the adhesive the adhesive with a wire pierce.
• Tie piano wire both ends to wire grip.
• Pull piano wire in turn and cut off adhesive.

8.

Remove front sunroof glass from vehicle using suction lifter.

WARNING:

Always wear safety glasses and heavy gloves to help prevent glass splinters from entering your eyes
or cutting your hands when cutting the glass from the vehicle.

CAUTION:

Never reuse the front sunroof glass which has been removed once.

INSTALLATION

WARNING:

• Keep heat and open flames away as primers and adhesive are flammable.
• The materials contained in the kit are harmful if swallowed, and may irritate skin and eyes. Never let

them in contact with the skin and eyes.

• Use in an open, well ventilated location. Never breathe the vapors. They may be harmful if inhaled.

Move immediately to an area with fresh air if affected by vapor inhalation.

NOTE:
• Use a genuine Nissan Urethane Adhesive Kit (if available) or an equivalent and follow the instructions fur-

nished with it.

• Inform the customer that the vehicle should remain stationary until the urethane adhesive has completely

cured (approximately 24 hours). Curing time varies with temperature and humidity.

1.

Using a knife or spatula, trim the adhesive (sealant) remaining
on body down to approximately 2 mm (0.08 in) thick (a) so that
the contour becomes smooth.

CAUTION:

If bonded area on body is scratched, be sure to repair it
with a 2-component urethane. Never use lacquer.

2.

Clean bonded area on glass with white gasoline.

3.

Apply glass primer along the entire circumference of glass.

CAUTION:

There are 2 types of primer. Never confuse the application methods.
Paint primer: for painted surfaces
Glass primer: for glass

4.

Apply paint primer on areas where adhesive contacts on the side of sunroof frame.

CAUTION:

If paint primer adheres to a painted surface other than bonding area, or if it overflows, quickly
remove it with white gasoline.

5.

After applying primers, apply the adhesive along the entire circumference of the glass as shown in the fig-
ure, and within the time specified in the instructions for the adhesive.
• Open adhesive by cutting off the nozzle tip and set it in a sealant gun.

6.

After setting suction lifter to glass, align mating marks on sunroof frame and glass. Install glass to the sun-
roof frame.

JMKIA0307ZZ

 

 

 

 

 

 

 

содержание   ..  1189  1190  1191  1192   ..