Content .. 37 38 39 40 ..

Murano Cross Cabriolet Z51 (2013 year). Manual - part 39

FSU-14

< REMOVAL AND INSTALLATION >

FRONT STABILIZER

FRONT STABILIZER

Exploded View

INFOID:0000000008461661

Removal and Installation

INFOID:0000000008461662

REMOVAL

Remove tires power tool.

Remove front exhaust tube. Refer to

EX-5, "Exploded View"

Remove rear propeller shaft from transfer. Refer to

DLN-79, "Exploded View"

Remove lock plate. Refer to

BR-20, "FRONT : Exploded View"

Remove wheel sensor harness from strut assembly. Refer to

BRC-98, "FRONT WHEEL SENSOR :

Exploded View"

Disconnect power steering solenoid valve harness connector. Refer to

ST-38, "Removal and Installation"

Remove steering outer socket from steering knuckle. Refer to

ST-37, "Exploded View"

Remove stabilizer connecting rod.

Remove mounting bolts (

) of stabilizer clamp, and then

remove stabilizer clamp and stabilizer bushing from front sus-
pension member.

10. Remove stabilizer bar.

INSTALLATION

Note the following, and install in the reverse order of removal.

Stabilizer clamp

Stabilizer bushing

Stabilizer bar

Front suspension member

Stabilizer connecting rod

Refer to

GI-4, "Components"

for symbols in the figure.

JPEIA0092GB

WEIA0182E

Revision: 2012 October

2013 Murano CrossCabriolet

FRONT STABILIZER

FSU-15

< REMOVAL AND INSTALLATION >

FSU

• Install stabilizer clamp that notch (A) becomes vehicle front side

(

• Install stabilizer bushing that slit (B) becomes vehicle front side

(

Inspection

INFOID:0000000008461663

INSPECTION AFTER REMOVAL

Check stabilizer bar, stabilizer connecting rod, stabilizer bushing and stabilizer clamp for deformation, cracks
or damage. Replace it if necessary.

JPEIA0058ZZ

Revision: 2012 October

2013 Murano CrossCabriolet

FSU-16

< REMOVAL AND INSTALLATION >

FRONT SUSPENSION MEMBER

FRONT SUSPENSION MEMBER

Exploded View

INFOID:0000000008461664

Removal and Installation

INFOID:0000000008461665

REMOVAL

Remove tires with power tool.

Remove air guide mounting nuts (

) and air guide (1).

At first, remove the engine and the transaxle assembly with front
suspension member downward. Then separate the engine, tran-
saxle and drive shaft. Refer to

EM-67, "Exploded View"

Remove the following parts.
• Steering knuckle and wheel hub and bearing assembly: refer

FAX-8, "Exploded View"

• Steering gear assembly and hydraulic line: refer to

ST-37,

"Exploded View"

and

ST-53, "Exploded View"

• Stabilizer bar: refer to

FSU-14, "Exploded View"

• Transverse link: refer to

FSU-12, "Exploded View"

INSTALLATION

Note the following, and install in the reverse order of removal.
• Perform final tightening of installation position between front suspension member and transverse links (rub-

ber bushing) under unladen condition with tires on level ground.

Inspection

INFOID:0000000008461666

INSPECTION AFTER REMOVAL

Check the front suspension member for significant deformation, cracks, or damages. Replace it if necessary.

INSPECTION AFTER INSTALLATION

Check wheel sensor harness for proper connection. Refer to

BRC-98, "FRONT WHEEL SENSOR :

Exploded View"

Check wheel alignment. Refer to

FSU-7, "Inspection"

Front suspension member

Rebound stopper

Front suspension member stay

Refer to

GI-4, "Components"

for symbols in the figure.

JPEIA0093GB

JPEIA0097ZZ

Revision: 2012 October

2013 Murano CrossCabriolet

SERVICE DATA AND SPECIFICATIONS (SDS)

FSU-17

< SERVICE DATA AND SPECIFICATIONS (SDS)

FSU

SERVICE DATA AND SPECIFICATIONS (SDS)

Wheel Alignment

INFOID:0000000008461667

Measure value under unladen*

conditions.

*1: A difference when assuming the left side a standard.

*2: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.

Ball Joint

INFOID:0000000008461668

Wheelarch Height

INFOID:0000000008461669

Item

Standard

Measurement wheel

Left side

Right side

Camber
Degree minute (Decimal degree)

Minimum

–1

′

(–1.00

)

–1

′

(–1.25

)

Nominal

–0

′

(–0.25

)

–0

′

(–0.50

)

Maximum

′

(0.50

)

′

(0.25

)

Left and right difference*

–0

′

(–0.30

) - 0

′

(0.80

)

Caster
Degree minute (Decimal degree)

Minimum

′

(4.00

)

′

(4.17

)

Nominal

′

(4.75

)

′

(4.92

)

Maximum

′

(5.50

)

′

(5.66

)

Left and right difference*

–0

′

(–0.30

) - 0

′

(0.80

)

Kingpin inclination
Degree minute (Decimal degree)

Minimum

′

(12.00

)

Nominal

′

(12.75

)

Maximum

′

(13.50

)

Toe-in

Total toe-in
Distance

Minimum

Out 0.5 mm (Out 0.019 in)

Nominal

In 1.5 mm (In 0.059 in)

Maximum

In 3.5 mm (In 0.137 in)

Total toe-angle
Degree minute (Decimal
degree)

Minimum

Out 0

′

(Out 0.03

)

Nominal

In 0

′

(In 0.1

)

Maximum

In 0

′

(In 0.23

)

Item

Standard

Swing torque

Transverse link

0.5 – 4.9 N·m (0.06 – 0.49 kg-m, 5 – 43 in-lb)

Measurement on spring balance

Transverse link

11.1 – 108.9 N (1.2 – 11.1 kg, 3 – 24 lb)

Axial end play

0 mm (0 in)

Item

Standard

Front (Hr)

843 mm (33.19 in)

Revision: 2012 October

2013 Murano CrossCabriolet

FSU-18

< SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS)

Measure value under unladen* conditions.

*: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.

Rear (Hr)

854 mm (33.62 in)

Item

Standard

SFA746B

Revision: 2012 October

2013 Murano CrossCabriolet

A
B

QUICK REFERENCE INDEX

A GENERAL INFORMATION

General Information

B ENGINE

Engine Mechanical

Engine Lubrication System

Engine Cooling System

Engine Control System

Accelerator Control System

C ELECTRIC POWER TRAIN

HBC

Hybrid Control System

HBB

Hybrid Battery System

HBR

Hybrid Brake System

EVC

EV Control System

TMS

Traction Motor System

EVB

EV Battery System

Vehicle Charging System

HCO

High Voltage Cooling System

D TRANSMISSION & DRIVELINE

Clutch

Transaxle & Transmission

E SUSPENSION

SCS

Suspension Control System

Road Wheels & Tires

F BRAKES

Brake System

Parking Brake System

BRC

Brake Control System

G STEERING

Steering System

STC

Steering Control System

H RESTRAINTS

Seat Belt

SBC

Seat Belt Control System

SRS Airbag

SRC

SRS Airbag Control System

VENTILATION, HEATER & AIR
CONDITIONER

VTL

Ventilation System

Heater & Air Conditioning System

HAC

Heater & Air Conditioning Control System

J BODY INTERIOR

Automatic Drive Positioner

K BODY EXTERIOR, DOORS,

ROOF & VEHICLE SECURITY

DLK

Door & Lock

SEC

Security Control System

Glass & Window System

PWC

Power Window Control System

Hood

L DRIVER CONTROLS

MIR

Mirrors

EXL

Exterior Lighting System

INL

Interior Lighting System

VSP

Approaching Vehicle Sound for Pedestrians (VSP)

M ELECTRICAL & POWER CON-

TROL

PWO

Power Outlet

BCS

Body Control System

LAN

LAN System

PCS

Power Control System

CHG

Charging System

Power Supply, Ground & Circuit Elements

N DRIVER INFORMATION &

MULTIMEDIA

MWI

Meter, Warning Lamp & Indicator

WCS

Warning Chime System

Sonar System

Audio, Visual & Navigation System

O CRUISE CONTROL &

DRIVER ASSISTANCE

CCS

Cruise Control System

DAS

Driver Assistance System

DMS

Drive Mode System

P MAINTENANCE

Maintenance

All Rights Reserved. No part
of this Service Manual may
be reproduced or stored in a
retrieval system, or transmit-
ted in any form, or by any
means, electronic, mechani-
cal, recording or otherwise,
without the prior written per-
mission of NISSAN MOTOR
CO., LTD.

Edition: October 2012
Publication No. SM3E-1Z51U1

FOREWORD

This manual contains maintenance and repair procedure for the 2013
NISSAN Murano CrossCabriolet.

In order to assure your safety and the efficient functioning of the vehicle,
this manual should be read thoroughly. It is especially important that the
PRECAUTIONS in the GI section be completely understood before starting
any repair task.

All information in this manual is based on the latest product information
at the time of publication. The right is reserved to make changes in specifi-
cations and methods at any time without notice.

IMPORTANT SAFETY NOTICE

The proper performance of service is essential for both the safety of
the technician and the efficient functioning of the vehicle.
The service methods in this Service Manual are described in such a
manner that the service may be performed safely and accurately.
Service varies with the procedures used, the skills of the technician
and the tools and parts available. Accordingly, anyone using service
procedures, tools or parts which are not specifically recommended
by NISSAN must first be completely satisfied that neither personal
safety nor the vehicle’s safety will be jeopardized by the service
method selected.

PLEASE HELP MAKE THIS SERVICE MANUAL BETTER!

Your comments are important to NISSAN and will help us to improve our Service Manuals.
Use this form to report any issues or comments you may have regarding our Service Manuals.
Please print this form and type or write your comments below. Mail or fax to:

Nissan North America, Inc.
Technical Service Information
39001 Sunrise Drive, P.O. Box 9200
Farmington Hills, MI USA 48331
FAX: (248) 488-3

SERVICE MANUAL: Model:

Year:

PUBLICATION NO. (Refer to Quick Reference Index ):

Please describe any Service Manual issues or problems in detail:
Page number(s)

Note: Please include a copy of each page, marked with your comments.

Are the trouble diagnosis procedures logical and easy to use? (circle your answer)

YES

If no, what page number(s)?

Note: Please include a copy of each page, marked with your comments.

Please describe the issue or problem in detail:

Is the organization of the manual clear and easy to follow? (circle your answer)

YES

Please comment:

What information should be included in NISSAN Service Manuals to better support you in servicing or
repairing customer vehicles?

DATE:

YOUR NAME:

POSITION:

DEALER:

DEALER NO.:

ADDRESS:

CITY:

STATE/PROV./COUNTRY:

ZIP/POSTAL CODE:

QUICK REFERENCE CHART MURANO

PFP:00000

ENGINE TUNE-UP DATA (VQ35DE)

ELS0003W

Engine model

VQ35DE

Firing order

1-2-3-4-5-6

Idle speed
CVT (In “P” or “N” position)

rpm

600 ± 50

Ignition timing (BTDC at idle speed)
CVT (In “P” or “N” position)

± 5

Tensions of drive belt

Belt tension is not necessary, as it is automatically adjusted by

drive belt auto-tensioner.

Radiator cap relief pressure

kPa (kg/cm

, psi)

Standard

122.3 - 151.7 (1.2 - 1.5, 17.7 - 22.0)

Limit

108 (1.1, 15.6)

Cooling system leakage testing pres-
sure

kPa (kg/cm

, psi)

156 (1.59, 22.6)

Compression pressure

kPa (kg/cm

, psi)/rpm

Standard

1,275 (13.0, 185)/300

Minimum

981 (10.0, 142)/300

Spark plug

Make

DENSO

Standard type

FXE22HR11

Gap

Standard

1.1 mm (0.043 in)

Limit

1.4 mm (0.055 in)

2013

QUICK REFERENCE CHART MURANO

FRONT WHEEL ALIGNMENT

ELS0003X

FOR USA AND MEXICO MODELS

Measure value under unladen*

conditions.

*1: A difference when assuming the left side a standard.
*2: Fuel, engine coolant and lubricant are oil full. Spare tire, jack, hand tools and mats are in designated positions.

FOR CANADA MODELS

Measure value under unladen*

conditions.

*1: A difference when assuming the left side a standard.
*2: Fuel, engine coolant and lubricant are oil full. Spare tire, jack, hand tools and mats are in designated positions.

Item

Standard

Measurement wheel

Left side

Right side

Camber
Degree minute (Decimal degree)

Minimum

–1

′

(–1.00

)

–1

′

(–1.25

)

Nominal

–0

′

(–0.25

)

–0

′

(–0.50

)

Maximum

′

(0.50

)

′

(0.25

)

Left and right difference*

–0

′

(–0

′

) - 0

′

(0.80

)

Caster
Degree minute (Decimal degree)

Minimum

′

(3.92

)

′

(4.25

)

Nominal

′

(4.67

)

′

(5.00

)

Maximum

′

(5.41

)

′

(5.75

)

Left and right difference*

–0

′

(–0

′

) - 0

′

(0.80

)

Kingpin inclination
Degree minute (Decimal degree)

Minimum

′

(12.00

)

Nominal

′

(12.75

)

Maximum

′

(13.50

)

Toe-in

Total toe-in
Distance

Minimum

Out 0.5 mm (Out 0.019 in)

Nominal

In 1.5 mm (In 0.059 in)

Maximum

In 3.5 mm (In 0.137 in)

Total toe-angle
Degree minute (Decimal degree)

Minimum

Out 0

′

(Out 0.03

)

Nominal

In 0

′

(In 0.1

)

Maximum

In 0

′

(In 0.23

)

Item

Standard

Measurement wheel

Left side

Right side

Camber
Degree minute (Decimal degree)

Minimum

–1

′

(–1.00

)

–1

′

(–1.25

)

Nominal

–0

′

(–0.25

)

–0

′

(–0.50

)

Maximum

′

(0.50

)

′

(0.25

)

Left and right difference*

–0

′

(–0

′

) - 0

′

(0.80

)

Caster
Degree minute (Decimal degree)

Minimum

′

(3.92

)

′

(4.17

)

Nominal

′

(4.67

)

′

(4.92

)

Maximum

′

(5.41

)

′

(5.66

)

Left and right difference*

–0

′

(–0.30

) - 0

′

(0.80

)

Kingpin inclination
Degree minute (Decimal degree)

Minimum

′

(11.92

)

Nominal

′

(12.67

)

Maximum

′

(13.41

)

Toe-in

Total toe-in
Distance

Minimum

Out 0.5 mm (Out 0.019 in)

Nominal

In 1.5 mm (In 0.059 in)

Maximum

In 3.5 mm (In 0.137 in)

Total toe-angle
Degree minute (Decimal degree)

Minimum

Out 0

′

(Out 0.03

)

Nominal

In 0

′

(In 0.1

)

Maximum

In 0

′

(In 0.23

)

2013

QUICK REFERENCE CHART MURANO

REAR WHEEL ALIGNMENT

ELS0003Y

FOR USA AND MEXICO MODELS

Measure value under unladen* conditions.
* : Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.

FOR CANADA MODELS

Measure value under unladen* conditions.
* : Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.

BRAKE PEDAL

ELS0003Z

Unit: mm (in)

BRAKE BOOSTER

Vacuum type

Unit: mm (in)

Item

Standard

Camber
Degree minute (Decimal degree)

Minimum

–1

′

(–1.21

)

Nominal

–0

′

(–0.72

)

Maximum

–0

′

(–0.21

)

Toe-in

Total toe-in
Distance

Minimum

In 0.9 mm (0.035 in)

Nominal

In 2.7 mm (0.106 in)

Maximum

In 4.5 mm (0.177 in)

Total toe-angle
Degree minute (Decimal degree)

Minimum

In 0

′

(In 0.07

)

Nominal

In 0

′

(In 0.20

)

Maximum

In 0

′

(In 0.33

)

Item

Standard

Camber
Degree minute (Decimal degree)

Minimum

–1

′

(–1.18

)

Nominal

–0

′

(–0.68

)

Maximum

–0

′

(–0.18

)

Toe-in

Total toe-in
Distance

Minimum

In 0.9 mm (0.035 in)

Nominal

In 2.7 mm (0.106 in)

Maximum

In 4.5 mm (0.177 in)

Total toe-angle
Degree minute (Decimal degree)

Minimum

In 0

′

(In 0.07

)

Nominal

In 0

′

(In 0.20

)

Maximum

In 0

′

(In 0.33

)

Item

Standard

Brake pedal height

197.1 - 207.1 (7.76 - 8.15)

Clearance between the stop lamp switch and ASCD brake switch
threaded end

0.20 - 1.96 (0.0079 - 0.0772)

Brake pedal play

3.0 - 11.0 (0.118 - 0.433)

Depressed brake pedal height
[Depressing 490 N (50 kg, 110 lb) while turning the engine ON]

128 (5.04) or more

Item

Standard

Input rod length

127 (5.00)

2013

QUICK REFERENCE CHART MURANO

FRONT DISC BRAKE

Unit: mm (in)

REAR DISC BRAKE

Unit: mm (in)

REFILL CAPACITIES

ELS00040

Item

Limit

Brake pad

Wear thickness

2.0 (0.079)

Disc rotor

Wear thickness

26.0 (1.024)

Thickness variation (measured at 8 positions)

0.008 (0.0003)

Runout (with it attached to the vehicle)

0.040 (0.0016) or less

Item

Limit

Brake pad

Wear thickness

2.0 (0.079)

Disc rotor

Wear thickness

14.0 (0.551)

Thickness variation (measured at 8 positions)

0.020 (0.0008)

Runout (with it attached to the vehicle)

0.050 (0.0020) or less

UNIT

Liter

US measure

Fuel tank

21-5/8 gal

Coolant ( With reservoir tank at “MAX” level )

9.0

9-1/2 qt

Engine

Drain and refill

With oil filter change

4.6

4-7/8 qt

Without oil filter change

4.3

4-1/2 qt

Dry engine (Overhaul)

5.3

5-5/8 qt

Transmission

CVT

10.2

10-3/4 qt

Transfer

0.31

5/8 pt

Final drive

0.55

1-1/8 pt

Power steering system

1.0

1-1/8 qt

Air conditioning system

Compressor oil

0.15

5.07 fl oz

Refrigerant

0.60 kg

1.32 lb

2013

GI-1

GENERAL INFORMATION

SECTION

CONTENTS

GENERAL INFORMATION

HOW TO USE THIS MANUAL ......................

HOW TO USE THIS MANUAL ............................

Description ................................................................

Terms ........................................................................

Units ..........................................................................

Contents ....................................................................

Relation between Illustrations and Descriptions .......

Components ..............................................................

HOW TO FOLLOW TROUBLE DIAGNOSES .....

Description ................................................................

How to Follow Test Groups in Trouble Diagnosis ......

Key to Symbols Signifying Measurements or Pro-
cedures .....................................................................

HOW TO READ WIRING DIAGRAMS ................

Connector Symbols ...................................................

Sample/Wiring Diagram -Example- .........................

Connector Information .............................................

ABBREVIATIONS ..............................................

Abbreviation List ......................................................

TIGHTENING TORQUE OF STANDARD
BOLTS ................................................................

Description ..............................................................

Tightening Torque Table (New Standard Includ-
ed) ...........................................................................

....

VEHICLE INFORMATION ............................

IDENTIFICATION INFORMATION .....................

Model Variation .......................................................

Information About Identification or Model Code ......

Dimensions .............................................................

Wheels & Tires ........................................................

PRECAUTION ..............................................

PRECAUTIONS .................................................

Description ...............................................................

Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" .................................................................

Precautions For Xenon Headlamp Service .............

Precaution for Procedure without Cowl Top Cover ....

Service Procedure Precautions for Models with a
Pop-up Roll Bar .......................................................

Precaution for Battery Service .................................

Cautions in Removing Battery Terminal and AV
Control Unit (Models with AV Control Unit) .............

General Precautions ................................................

Three Way Catalyst .................................................

Multiport Fuel Injection System or Engine Control
System .....................................................................

Hoses ......................................................................

Engine Oils ..............................................................

Air Conditioning .......................................................

Fuel ..........................................................................

LIFTING POINT .................................................

Commercial Service Tools .......................................

Garage Jack and Safety Stand and 2-Pole Lift .......

Board-On Lift ...........................................................

TOW TRUCK TOWING .....................................

Tow Truck Towing ...................................................

Vehicle Recovery (Freeing a Stuck Vehicle) ...........

BASIC INSPECTION ...................................

SERVICE INFORMATION FOR ELECTRICAL
INCIDENT ..........................................................

Work Flow ................................................................

Control Units and Electrical Parts ............................

How to Check Terminal ...........................................

Intermittent Incident .................................................

Circuit Inspection .....................................................

Revision: 2012 October

2013 Murano CrossCabriolet

GI-2

CONSULT/GST CHECKING SYSTEM ..............

Description ..............................................................

CONSULT Function and System Application*1 ......

CONSULT/GST Data Link Connector (DLC) Cir-
cuit ..........................................................................

Wiring Diagram - CONSULT/GST CHECKING
SYSTEM - ...............................................................

INSPECTION AND ADJUSTMENT ...................

ADDITIONAL SERVICE WHEN REMOVING BAT-
TERY NEGATIVE TERMINAL ..................................

ADDITIONAL SERVICE WHEN REMOVING
BATTERY NEGATIVE TERMINAL : Required
Procedure After Battery Disconnection ...................

Revision: 2012 October

2013 Murano CrossCabriolet

HOW TO USE THIS MANUAL

GI-3

< HOW TO USE THIS MANUAL >

HOW TO USE THIS MANUAL

Description

INFOID:0000000008461554

This volume explains “Removal, Disassembly, Installation, Inspection and Adjustment” and “Trouble Diag-
noses”.

Terms

INFOID:0000000008461555

• The captions WARNING and CAUTION warn you of steps that must be followed to prevent personal injury

and/or damage to some part of the vehicle.
WARNING indicates the possibility of personal injury if instructions are not followed.
CAUTION indicates the possibility of component damage if instructions are not followed.
BOLD TYPED STATEMENTS except WARNING and CAUTION give you helpful information.
Standard value: Tolerance at inspection and adjustment.
Limit value: The maximum or minimum limit value that should not be exceeded at inspection and adjust-
ment.

Units

INFOID:0000000008461556

• The UNITS given in this manual are primarily expressed as the SI UNIT (International System of Unit), and

alternatively expressed in the metric system and in the yard/pound system.
Also with regard to tightening torque of bolts and nuts, there are descriptions both about range and about the
standard tightening torque.

“Example”
Range

Standard

Contents

INFOID:0000000008461557

• A QUICK REFERENCE INDEX, a black tab (e.g.

) is provided on the first page. You can quickly find the

first page of each section by matching it to the section's black tab.

• THE CONTENTS are listed on the first page of each section.
• THE TITLE is indicated on the upper portion of each page and shows the part or system.
• THE PAGE NUMBER of each section consists of two or three letters which designate the particular section

and a number (e.g. “BR-5”).

• THE SMALL ILLUSTRATIONS show the important steps such as inspection, use of special tools, knacks of

work and hidden or tricky steps which are not shown in the previous large illustrations.
Assembly, inspection and adjustment procedures for the complicated units such as the automatic transaxle
or transmission, etc. are presented in a step-by-step format where necessary.

Outer Socket Lock Nut

: 59 - 78 N·m (6.0 - 8.0 kg-m, 43 - 58 ft-lb)

Drive Shaft Installation Bolt

: 44.3 N·m (4.5 kg-m, 33 ft-lb)

Revision: 2012 October

2013 Murano CrossCabriolet

GI-4

< HOW TO USE THIS MANUAL >

HOW TO USE THIS MANUAL

Relation between Illustrations and Descriptions

INFOID:0000000008461558

The following sample explains the relationship between the part description in an illustration, the part name in
the text and the service procedures.

Components

INFOID:0000000008461559

• THE LARGE ILLUSTRATIONS are exploded views (see the following) and contain tightening torques, lubri-

cation points, section number of the PARTS CATALOG (e.g. SEC. 440) and other information necessary to
perform repairs.
The illustrations should be used in reference to service matters only. When ordering parts, refer to the appro-
priate PARTS CATALOG.
Components shown in an illustration may be identified by a circled number. When this style of illustration is
used, the text description of the components will follow the illustration.

SAIA0519E

Revision: 2012 October

2013 Murano CrossCabriolet

Content .. 37 38 39 40 ..