Murano Cross Cabriolet Z51 (2013 year). Manual

SERVICE DATA AND SPECIFICATIONS (SDS)

FAX-25

< SERVICE DATA AND SPECIFICATIONS (SDS)

FAX

SERVICE DATA AND SPECIFICATIONS (SDS)

Wheel Bearing

INFOID:0000000008463533

Drive Shaft

INFOID:0000000008463534

Item

Standard

Axial end play

0.05 mm (0.002 in) or less

Item

Standard

Left side

Right side

Grease quantity

Wheel side

170 – 190 g (6.00 – 6.70 oz)

Transaxle side

155 – 175 g (5.47 – 6.17 oz)

Boots installed length

Wheel side

158.6 mm (6.24 in)

Transaxle side

163.67 mm (6.44 in)

159.47 mm (6.28 in)

Dimension of dynamic damper

—

202 – 208 mm (7.95 – 8.19 in)

Revision: 2012 October

2013 Murano CrossCabriolet

FL-2

< PRECAUTION >

PRECAUTIONS

PRECAUTION

PRECAUTIONS

General Precautions

INFOID:0000000008462072

WARNING:

When replacing fuel line parts, be sure to observe the following.
• Put a “CAUTION: FLAMMABLE” sign in the workshop.
• Be sure to work in a well ventilated area and furnish workshop with a CO

fire extinguisher.

• Never smoke while servicing fuel system. Keep open flames and sparks away from the work area.

CAUTION:

• Use gasoline required by the regulations for octane number. Refer to

GI-31, "Fuel"

• Before removing fuel line parts, perform out the following procedures:
- Put drained fuel in an explosion-proof container and put the lid on securely. Keep the container in

safe area.

- Release fuel pressure from the fuel lines. Refer to

EC-125, "Work Procedure"

- Disconnect the battery cable from the negative terminal.
• Always replace O-ring and clamps with new ones.
• Never kink or twist tubes when they are being installed.
• Never tighten hose clamps excessively to avoid damaging hoses.
• After installing tubes, check there is no fuel leakage at connections in the following steps.
- Apply fuel pressure to fuel lines with turning ignition switch “ON” (with engine stopped). Then check

for fuel leakage at connections.

- Start engine and rev it up and check for fuel leakage at connections.
• Use only a genuine NISSAN fuel filler cap as a replacement. If an incorrect fuel filler cap is used, the

“MIL” may come on.

• For servicing “On Board Refueling Vapor Recovery (ORVR)” parts, refer to

EC-30, "On Board Refuel-

ing Vapor Recovery (ORVR)"

Revision: 2012 October

2013 Murano CrossCabriolet

PREPARATION

FL-3

< PREPARATION >

PREPARATION

Special Service Tool

INFOID:0000000008462073

The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.

Commercial Service Tool

INFOID:0000000008462074

(Kent-Moore No.)
Tool name

Description

(J-46211)
Fuel tank lock ring wrench

Removing and installing fuel tank retainer

SBIA0388E

Tool name

Description

Power tool

Loosening nuts and bolts

PBIC0190E

Revision: 2012 October

2013 Murano CrossCabriolet

FL-4

< PERIODIC MAINTENANCE >

FUEL SYSTEM

PERIODIC MAINTENANCE

FUEL SYSTEM

Inspection

INFOID:0000000008462075

Inspect fuel lines, fuel filler cap, and fuel tank for improper attach-
ment, leakage, cracks, damage, loose connections, chafing or dete-
rioration.

If necessary, repair or replace damaged parts.

Quick Connector

INFOID:0000000008462076

CAUTION:

• After connecting fuel tube quick connectors, check quick con-

nectors are secure.

• Ensure that connector and resin tube never contact any adja-

cent parts.

: Engine

: Fuel line

: Fuel tank

JPBIA0129ZZ

: Quick connector

: Retainer

: Hard tube (or the equivalent)

: Connection (cross-section)

: Resin tube

: To under floor fuel line

: To fuel tank

: Tab

: Disconnection

JPBIA0130ZZ

Revision: 2012 October

2013 Murano CrossCabriolet

FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY

FL-5

< REMOVAL AND INSTALLATION >

REMOVAL AND INSTALLATION

FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY

Exploded View

INFOID:0000000008462077

REMOVAL

DISASSEMBLY

Retainer

Sub fuel level sensor unit

Seal packing

Main fuel level sensor unit, fuel filter
and fuel pump assembly

Right side

Left side

: Vehicle front

: Always replace after every disassembly.

JPBIA1694GB

Revision: 2012 October

2013 Murano CrossCabriolet

FL-6

< REMOVAL AND INSTALLATION >

FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY

Removal and Installation

INFOID:0000000008462078

WARNING:

Read “General Precautions” when working on the fuel system. Refer to

FL-2, "General Precautions"

REMOVAL

Check fuel level on a level ground. If the fuel level is 7/8 of the fuel tank (full or nearly full), draw appropri-
ate amount of fuel from the fuel tank.

• In the event of malfunction in fuel pump, insert a hose measuring 25 mm (0.98 in) in diameter into the

filler opening to draw approximately 20 liters fuel.

Release the fuel pressure from the fuel lines. Refer to

EC-125, "Work Procedure"

Open fuel filler lid.

Open filler cap and release the pressure inside fuel tank.

Remove rear seat cushion and reclining device assembly. Refer to

SE-48, "Exploded View"

Remove inspection hole cover. Refer to

SE-48, "Exploded View"

Peel off floor carpet, then remove inspection hole cover units by
turning clips clockwise by 90 degrees.

Sub fuel level sensor unit

Sub fuel level sensor unit base

Fuel filter and fuel pump assembly

Fuel level sensor unit

: Vehicle front

PBIC4901J

Guideline

: Draw approximately 20 liters from a full-tank condition

Left side

: Main fuel level sensor unit, fuel filter
and fuel pump assembly

Right side

: Sub fuel level sensor unit

SBIA0479E

Revision: 2012 October

2013 Murano CrossCabriolet

FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY

FL-7

< REMOVAL AND INSTALLATION >

Disconnect harness connector, fuel feed tube and EVAP hose.

Disconnect quick connector as follows:

• Hold the sides of connector, push in tabs (B) and pull out fuel

feed tube.

• If quick connector sticks to tube of main fuel level sensor unit,

push and pull quick connector several times until they start to
move. Then disconnect them by pulling.

CAUTION:

• Quick connector (1) can be disconnected when the tabs

(F) are completely depressed. Never twist it more than
necessary.

• Never use any tools to disconnected quick connector.
• Keep resin tube (C) away from heat. Be especially careful

when welding near the resin tube.

• Prevent acid liquid such as battery electrolyte, etc. from

getting on resin tube.

• Never bend or twist resin tube during installation and dis-

connection.

• Never remove the remaining retainer (2) on hard tube (or

the equivalent) (A) except when resin tube or retainer is
replaced.

• When resin tube or hard tube (or the equivalent) is

replaced, also replace retainer with new one.

PBIC1807E

: Pull

JPBIA0134ZZ

: Connection (cross-section)

: To under floor fuel line

: To fuel tank

: Disconnection

Retainer color: Green

JPBIA0130ZZ

Revision: 2012 October

2013 Murano CrossCabriolet

FL-8

< REMOVAL AND INSTALLATION >

FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY

• To keep the connecting portion clean and to avoid dam-

age and foreign materials, cover them completely with
plastic bags (A) or something similar.

Remove retainer for main fuel level sensor unit, fuel filter and
fuel pump assembly and sub fuel level sensor unit with fuel tank
lock ring wrench (SST) by turning counterclockwise.

10. Remove main fuel level sensor unit, fuel filter and fuel pump assembly, and sub fuel level sensor unit.

• Raise main fuel level sensor unit, fuel filter and fuel pump

assembly, and disconnect fuel hose connector (push in tabs
and pull out) and sub fuel level sensor unit harness connector.

• Raise and release sub fuel level sensor unit to remove.

INSTALLATION

Note to the following, and install in the reverse order of removal.

Main and Sub Fuel Level Sensor Unit

Install new seal packing to fuel tank without any twist.

Connect fuel hose connector (push in until it stops) and sub fuel
level sensor unit harness connector.
NOTE:
When installing fuel hose connector insert them fully until a click
sound of full stopper engagement is heard.

JPBIA0135ZZ

SBIA0411E

SBIA0396E

SBIA0398E

Revision: 2012 October

2013 Murano CrossCabriolet

FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY

FL-9

< REMOVAL AND INSTALLATION >

Align the direction mark on main fuel level sensor unit, fuel filter
and fuel pump assembly and sub fuel level sensor unit with that
on fuel tank as shown in the figure, and install them to fuel tank.

CAUTION:

• Never allow seal packing to drop.
• Never bend float arm during installing.

Install retainer for main fuel level sensor unit, fuel filter and fuel
pump assembly and sub fuel level sensor unit with fuel tank lock
ring wrench (SST) by turning clockwise.

CAUTION:

Install retainer horizontally.

Quick Connector

Connect quick connector as follows:

Check the connection for damage or any foreign materials.

Align the connector with the tube, then insert the connector straight into the tube until a click sound is
heard.

After connecting, check that the connection is secure by following method.
• Pull (A) the tube and the connector to check they are securely

connected.

• Visually confirm that the two retainer tabs are connected to the

connector.

Disassembly and Assembly

INFOID:0000000008462079

DISASSEMBLY

Fuel level sensor unit, fuel filter and fuel pump assembly side

Disconnect harness connector.

Remove fuel level sensor unit according to the following procedure.

SBIA0397E

SBIA0411E

JPBIA0140ZZ

Revision: 2012 October

2013 Murano CrossCabriolet

FL-10

< REMOVAL AND INSTALLATION >

FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY

Push the pawl of fuel level sensor unit (1) mounting area with an
L-shaped iron rod or an equivalent to unlock.

CAUTION:

Never damage it.

With the fuel level sensor unit unlocked, slide it in the direction
shown by the arrow (

Sub fuel level sensor unit assembly side

Remove sub fuel level sensor unit according to the following procedure.

Push the pawl of sub fuel level sensor unit (1) mounting area
with an L-shaped iron rod or an equivalent to unlock.

CAUTION:

Never damage it.

With the sub fuel level sensor unit unlocked, slide it in the direc-
tion shown by the arrow (

ASSEMBLY

Install fuel level sensor unit and sub fuel level sensor unit according to the following procedure.
• Insert fuel level sensor unit and sub fuel level sensor unit all the way to the end until a “click” touch and

sound can be recognized.

• Pull fuel level sensor unit and sub fuel level sensor unit in the removal direction to ensure that they do not

become detached.

Inspection

INFOID:0000000008462080

INSPECTION AFTER INSTALLATION

Use the following procedure to check for fuel leakage.
1.

Turn ignition switch “ON” (with engine stopped), then check connections for leakage by applying fuel pres-
sure to fuel piping.

Start engine and let it idle and check there are no fuel leakage at the fuel system connections.

PBIC4900J

PBIC4899J

Revision: 2012 October

2013 Murano CrossCabriolet

FUEL TANK

FL-11

< REMOVAL AND INSTALLATION >

FUEL TANK

Exploded View

INFOID:0000000008462081

Removal and Installation

INFOID:0000000008462082

WARNING:

Be sure to read “General Precautions” when working on the fuel system. Refer to

FL-2, "General Pre-

cautions"

REMOVAL

• Drain fuel from fuel tank if necessary. Refer to

FL-6, "Removal and Installation"

• Perform work on level place.

Perform steps 2 to 7 of “REMOVAL” in “ FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP
ASSEMBLY” on main and sub fuel level sensor units. Refer to

FL-6, "Removal and Installation"

Remove center muffler. Refer to

EX-5, "Exploded View"

Remove propeller shaft. Refer to

DLN-79, "Exploded View"

Clamp

EVAP/Vent line hose

Fuel tank

Fuel tank mounting band (RH)

Fuel tank protector

Fuel tank protector (RH)

Fuel tank protector (LH)

Fuel tank mounting band (LH)

Clamp

10. Clamp

11.

Fuel filler hose

12. EVAP (Recirculation) hose

13. Clamp

14.

Fuel filler tube

15. Grommet

16. Fuel filler cap

: N·m (kg-m, ft-lb)

: N·m (kg-m, in-lb)

JPBIA5442GB

Revision: 2012 October

2013 Murano CrossCabriolet

FL-12

< REMOVAL AND INSTALLATION >

FUEL TANK

Remove parking rear brake cables. Refer to

PB-6, "Exploded View"

Remove rear suspension member assembly. Refer to

RSU-18, "Exploded View"

NOTE:
For this service, drive shaft, final drive, and rear suspension member are required not to be separate one
another during removal.

Remove fuel tank protectors.

Disconnect fuel filler hose (1), EVAP/Vent line hose (3), and
EVAP (Recirculation) hose (2) from the side other than the fuel
tank side.

Support the lower part of fuel tank (1) with transmission jack (A).

CAUTION:

Support the position that fuel tank mounting bands never
engage.

Remove fuel tank mounting bands.

10. Supporting with hands, descend transmission jack carefully, and remove fuel tank.

CAUTION:

• Check that all connection points have been disconnected.
• Confirm there is no interference with vehicle.

11. Remove fuel filler tube if necessary.

INSTALLATION

Note the following, and install in the reverse order of removal.
• Surely clamp fuel hoses and insert hose to the length below.

• Be sure hose clamp is not placed on swelled area of fuel tube.
• Tighten the clamp hand with the top mark (A) until the mark is on

the bolt head flange.

• To connect quick connector, refer to

FL-6, "Removal and Installation"

: Vehicle front

JPBIA1696ZZ

JPBIA0145ZZ

Fuel filler hose

: 35 mm (1.38 in)

The other hoses

: 25 mm (0.98 in)

JPBIA0146ZZ

Revision: 2012 October

2013 Murano CrossCabriolet

FUEL TANK

FL-13

< REMOVAL AND INSTALLATION >

Inspection

INFOID:0000000008462083

INSPECTION AFTER INSTALLATION

Use the following procedure to check for fuel leakage.
1.

Turn ignition switch “ON” (with engine stopped), and check connections for leakage by applying fuel pres-
sure to fuel piping.

Start engine and rev it up and check there are no fuel leakage at the fuel system tube and hose connec-
tions.

• After removing/installing rear suspension assembly, check to adjust wheel alignment and then, adjust neutral

position of steering angle sensor. Refer to

RSU-6, "Inspection"

and

BRC-31, "Work Procedure"

Revision: 2012 October

2013 Murano CrossCabriolet

FL-14

< REMOVAL AND INSTALLATION >

EVAP CANISTER

EVAP CANISTER

Hydraulic Layout

INFOID:0000000008462084

EVAPORATIVE EMISSION LINE DRAWING

Intake manifold collector

EVAP canister purge volume control
solenoid valve

EVAP service port

From EVAP canister

: Vehicle front

ALBIA0106ZZ

Revision: 2012 October

2013 Murano CrossCabriolet

EVAP CANISTER

FL-15

< REMOVAL AND INSTALLATION >

NOTE:
Do not use soapy water or any type of solvent while installing vacuum hose or purge hoses.

EVAP control system pressure sen-
sor

EVAP canister vent control valve

EVAP canister

To previous figure

To/From B in this figure

Refer to previous figure

: Vehicle front

JMBIA1122ZZ

Revision: 2012 October

2013 Murano CrossCabriolet

Murano Cross Cabriolet Z51 (2013 year). Manual - part 37