Murano Cross Cabriolet Z51 (2013 year). Manual - part 36

BRC-98, "FRONT WHEEL SENSOR : Exploded

for symbols not described on the above.

JPDIF0243ZZ

Joint sub-assembly

Circular clip

Boot band

Boot

Damper band

Dynamic damper

Housing assembly

Circular clip

Dust shield

10. Oil seal

11.

Bearing housing

12. Bearing bracket

JPDIF0241GB

Revision: 2012 October

2013 Murano CrossCabriolet

FRONT DRIVE SHAFT BOOT

FAX-11

< REMOVAL AND INSTALLATION >

FAX

WHEEL SIDE

WHEEL SIDE : Removal and Installation

INFOID:0000000008463524

REMOVAL

Remove tires with power tool.

Remove wheel sensor and sensor harness. Refer to

Remove lock plate from strut assembly. Refer to

CALIPER ASSEMBLY (1 PISTON TYPE) : Exploded View"

Remove caliper assembly. Hang caliper assembly not to interfere with work. Refer to

BR-36, "BRAKE

(1 piston type) or

BR-40, "BRAKE CALIPER

ASSEMBLY (2 PISTON TYPE) : Exploded View"

(2 piston type).

CAUTION:

Never depress brake pedal while brake caliper is removed.

Remove disc rotor. Refer to

BR-41, "BRAKE CALIPER ASSEMBLY (2 PISTON TYPE) : Removal and

Installation"

Remove cotter pin, and then loosen wheel hub lock nut with power tool. Refer to

FAX-8, "Exploded View"

Patch wheel hub lock nut with a piece of wood. Hammer the wood to disengage wheel hub and bearing
assembly from drive shaft.

CAUTION:

• Never place drive shaft joint at an extreme angle. Also be careful not to overextend slide joint.
• Never allow drive shaft to hang down without support for joint sub-assembly, housing assembly

and the other parts.

NOTE:
Use suitable puller, if wheel hub and bearing assembly and drive shaft cannot be separated even after
performing the above procedure.

Remove wheel hub lock nut.

Remove strut assembly from steering knuckle. Refer to

10. Remove drive shaft from wheel hub and bearing assembly.
11. Remove boot bands, and then remove boot from joint sub-assembly.

12. Screw drive shaft puller (A) into joint sub-assembly screw part to

a length of 30 mm (1.18 in) or more. Support drive shaft with one
hand and pull out joint sub-assembly with a sliding hammer (B)
from housing assembly.

CAUTION:

• Align a sliding hammer and drive shaft and remove them

by pulling firmly and uniformly.

• If joint sub-assembly cannot be pulled out, try after

removing drive shaft from vehicle.

13. Snap ling

14. Dust shield

15. Color

16. Link shaft

17. Support bearing bracket

Oil seal lip

: Wheel side

1: Fill NISSAN Genuine grease or equivalent.

2: Apply paste [service parts (440037S000)].

3: Apply multi - purpose grease.

Refer to

for symbols not described on the above.

JPDIF0022ZZ

Revision: 2012 October

2013 Murano CrossCabriolet

FAX-12

< REMOVAL AND INSTALLATION >

FRONT DRIVE SHAFT BOOT

13. Remove circular clip (1) from housing assembly.

14. Remove boot from housing assembly.

INSTALLATION

Clean the old grease on joint sub-assembly with paper waste.

Fill serration slot joint sub-assembly with NISSAN genuine grease or equivalent until the serration slot and
ball groove become full to the brim.

CAUTION:

After applying grease, use a paper waste to wipe off old grease that has oozed out.

Install boot and boot bands to housing assembly.

CAUTION:

• Wrap serration on housing assembly with tape to protect the boot from damage.
• Never reuse boot and boot band.

Remove the tape wrapped around the serration on housing assembly.

Position the circular clip on groove at the housing assembly edge.

CAUTION:

Never reuse circular clip.
NOTE:
Drive joint inserter is recommended when installing circular clip.

Align both center axles of the housing assembly edge and joint sub-assembly. Then assemble housing
assembly with joint sub-assembly holding circular clip.

Install joint sub-assembly (1) to housing assembly using plastic
hammer.

CAUTION:

Confirm that joint sub-assembly is correctly engaged while
rotating drive housing assembly.

Apply the specified amount of grease into the boot inside from
large diameter side of boot.

Install the boot securely into grooves (indicated by “*” marks)
shown in the figure.

CAUTION:

If grease adheres to the boot mounting surface (indicated
by “*” mark) on the housing assembly or joint sub-assem-
bly, boot may be removed. Remove all grease from the boot
mounting surface.

10. To prevent the deformation of the boot, adjust the boot installa-

tion length (L) to the specified value shown below by inserting
the suitable tool into inside of the boot from the large diameter
side of the boot and discharging the inside air.

CAUTION:

• If the boot mounting length exceeds the standard, it may cause breakage of boot.

JPDIF0007ZZ

Grease amount

: Refer to

JPDIF0011ZZ

: Refer to

JPDIF0222ZZ

Revision: 2012 October

2013 Murano CrossCabriolet

FRONT DRIVE SHAFT BOOT

FAX-13

< REMOVAL AND INSTALLATION >

FAX

• Be careful not to touch the inside of the boot with a tip of tool.

11. Secure the large and small ends of the boot with boot bands

using the boot band crimping tool (A) [SST: KV40107300 (

—

)].

CAUTION:

Never reuse boot band.

NOTE:
Secure boot band so that dimension (A) meets the specification
as shown in the figure.

12. Secure joint sub-assembly and housing assembly, and then

make sure that they are in the correct position when rotating
boot. Reinstall them using boot bands when boot installation
positions become incorrect.

CAUTION:

Never reuse boot band.

13. Clean the matching surface of wheel hub lock nut and wheel

hub and bearing assembly.

CAUTION:

Never apply lubricating oil to these matching surface.

14. Clean the matching surface of drive shaft and wheel hub and bearing assembly.

CAUTION:

Apply paste [service parts (440037S000)] to cover entire flat
surface (A) of joint sub-assembly of drive shaft.

15. Insert drive shaft to wheel hub and bearing assembly, and then temporarily tighten wheel hub lock nut.

16. Install strut assembly to steering knuckle. Refer to

BR-41, "BRAKE CALIPER ASSEMBLY (2 PISTON TYPE) : Removal and Instal-

17. Install disc rotor. Refer to

lation"

18. Install caliper assembly to steering knuckle. Refer to

BR-36, "BRAKE CALIPER ASSEMBLY (1 PISTON

TYPE) : Exploded View"

(1 piston type) or

BR-40, "BRAKE CALIPER ASSEMBLY (2 PISTON TYPE) :

Exploded View"

(2 piston type).

19. Install lock plate to strut assembly. Refer to

BRC-98, "FRONT WHEEL SEN-

20. Install wheel sensor and sensor harness to steering knuckle. Refer to

SOR : Exploded View"

21. Tighten the wheel hub lock nut to the specified torque. Refer to

FAX-8, "Exploded View"

NOTE:
• Never use a power tool to tighten the wheel hub lock nut.
• Perform the final tightening of each of parts under unladen conditions, which were removed when

removing wheel hub and bearing assembly and axle housing.

JPDIF0012ZZ

: 7.0 mm (0.276 in) or less

Amount paste

: 1.0 – 3.0 g (0.04 – 0.10 oz)

JPDIF0268ZZ

JPDIG0122ZZ

Revision: 2012 October

2013 Murano CrossCabriolet

FAX-14

< REMOVAL AND INSTALLATION >

FRONT DRIVE SHAFT BOOT

22. Install cotter pin. Refer to

FAX-8, "Exploded View"

CAUTION:

• Never reuse cotter pin.
• Bend cotter pin at the root sufficiently to prevent any looseness.

TRANSAXLE SIDE

TRANSAXLE SIDE : Removal and Installation

INFOID:0000000008463525

NOTE:
Remove boot after removing drive shaft. Refer to

FAX-16, "LEFT SIDE : Removal and Installation"

(left side),

FAX-17, "RIGHT SIDE : Removal and Installation"

(right side).

Inspection

INFOID:0000000008463526

INSPECTION AFTER REMOVAL

• Move joint up/down, left/right, and in the axial directions. Check for motion that is not smooth and for signifi-

cant looseness.

• Check boot for cracks, damage, and leakage of grease.
• Disassemble drive shaft and exchange malfunctioning part if there

is a non-standard condition.

SDIA1190J

Revision: 2012 October

2013 Murano CrossCabriolet

FRONT DRIVE SHAFT

FAX-15

< REMOVAL AND INSTALLATION >

FAX

FRONT DRIVE SHAFT

Exploded View

INFOID:0000000008463527

LEFT SIDE

RIGHT SIDE

Circular clip

Dust shield

Housing assembly

Boot band

Boot

Circular clip

Joint sub-assembly

: Wheel side

1: Fill NISSAN Genuine grease or equivalent.

2: Apply paste [service parts (440037S000)].

Refer to

BRC-98, "FRONT WHEEL SENSOR : Exploded

for symbols not described on the above.

JPDIF0243ZZ

Joint sub-assembly

Circular clip

Boot band

Boot

Damper band

Dynamic damper

Housing assembly

Circular clip

Dust shield

10. Oil seal

11.

Bearing housing

12. Bearing bracket

JPDIF0241GB

Revision: 2012 October

2013 Murano CrossCabriolet

FAX-16

< REMOVAL AND INSTALLATION >

FRONT DRIVE SHAFT

LEFT SIDE

LEFT SIDE : Removal and Installation

INFOID:0000000008463528

REMOVAL

Remove tires with power tool.

Remove wheel sensor and sensor harness. Refer to

Remove lock plate from strut assembly. Refer to

CALIPER ASSEMBLY (1 PISTON TYPE) : Exploded View"

Remove caliper assembly. Hang caliper assembly not to interfere with work. Refer to

BR-36, "BRAKE

(1 piston type) or

BR-40, "BRAKE CALIPER

ASSEMBLY (2 PISTON TYPE) : Exploded View"

(2 piston type).

CAUTION:

Never depress brake pedal while brake caliper is removed.

Remove disc rotor. Refer to

BR-41, "BRAKE CALIPER ASSEMBLY (2 PISTON TYPE) : Removal and

Installation"

Remove cotter pin, and then loosen wheel hub lock nut with power tool.

Patch wheel hub lock nut with a piece of wood. Hammer the wood to disengage wheel hub and bearing
assembly from drive shaft.

CAUTION:

• Never place drive shaft joint at an extreme angle. Also be careful not to overextend slide joint.
• Never allow drive shaft to hang down without support for joint sub-assembly, housing assembly

and the other parts.

NOTE:
Use suitable puller, if wheel hub and bearing assembly and drive shaft cannot be separated even after
performing the above procedure.

Remove wheel hub lock nut.

Remove strut assembly from steering knuckle. Refer to

10. Remove drive shaft from transaxle assembly.

• Use the drive shaft attachment (A) [SST: KV40107500 (

—

)] and a sliding hammer (B) while inserting tip of the drive

shaft attachment between housing assembly and transaxle
assembly.

CAUTION:

• Never place drive shaft joint at an extreme angle when

removing drive shaft. Also be careful not to overextend
slide joint.

• Confirm that the circular clip is attached to the drive

shaft.

INSTALLATION

Note the following, and install in the reverse order of removal.
• Always replace differential side oil seal with new one when installing drive shaft. Refer to

TM-152, "Exploded

13. Snap ling

14. Dust shield

15. Color

16. Link shaft

17. Support bearing bracket

Oil seal lip

: Wheel side

1: Fill NISSAN Genuine grease or equivalent.

2: Apply paste [service parts (440037S000)].

3: Apply multi - purpose grease.

Refer to

BRC-98, "FRONT WHEEL SENSOR : Exploded

for symbols not described on the above.

JPDIF0004ZZ

Revision: 2012 October

2013 Murano CrossCabriolet

FRONT DRIVE SHAFT

FAX-17

< REMOVAL AND INSTALLATION >

FAX

• Place the protector (A) [SST: KV38107900 (

—

)] onto transaxle

assembly to prevent damage to the oil seal while inserting drive
shaft. Slide drive shaft sliding joint and tap with a hammer to install
securely.

CAUTION:

Make sure that circular clip is completely engaged.

• Clean the matching surface of wheel hub lock nut and wheel hub and bearing assembly.

CAUTION:

Never apply lubricating oil to these matching surface.

• Clean the matching surface of drive shaft and wheel hub and bearing assembly.

CAUTION:

Apply paste [service parts (440037S000)] to cover entire flat
surface (A) of joint sub-assembly of drive shaft.

• Never use a power tool to tighten the wheel hub lock nut.
• Perform the final tightening of each of parts under unladen condi-

tions, which were removed when removing wheel hub and bearing
assembly and axle housing.

• Never reuse cotter pin.

RIGHT SIDE

RIGHT SIDE : Removal and Installation

INFOID:0000000008463529

REMOVAL

Remove tires with power tool.

Remove wheel sensor and sensor harness. Refer to

Remove lock plate from strut assembly. Refer to

CALIPER ASSEMBLY (1 PISTON TYPE) : Exploded View"

Remove caliper assembly. Hang caliper assembly not to interfere with work. Refer to

BR-36, "BRAKE

(1 piston type) or

BR-40, "BRAKE CALIPER

ASSEMBLY (2 PISTON TYPE) : Exploded View"

(2 piston type).

CAUTION:

Never depress brake pedal while brake caliper is removed.

Remove disc rotor. Refer to

BR-41, "BRAKE CALIPER ASSEMBLY (2 PISTON TYPE) : Removal and

Installation"

Remove cotter pin, and then loosen wheel hub lock nut with power tool.

Patch wheel hub lock nut with a piece of wood. Hammer the wood to disengage wheel hub and bearing
assembly from drive shaft.

CAUTION:

• Never place drive shaft joint at an extreme angle. Also be careful not to overextend slide joint.
• Never allow drive shaft to hang down without support for joint sub-assembly, housing assembly

and the other parts.

NOTE:
Use suitable puller, if wheel hub and bearing assembly and drive shaft cannot be separated even after
performing the above procedure.

Remove wheel hub lock nut.

Remove strut assembly from steering knuckle. Refer to

10. Remove drive shaft from wheel hub and bearing assembly.

JPDIF0023ZZ

Amount paste

: 1.0 – 3.0 g (0.04 – 0.10 oz)

JPDIG0122ZZ

Revision: 2012 October

2013 Murano CrossCabriolet

FAX-18

< REMOVAL AND INSTALLATION >

FRONT DRIVE SHAFT

11. Remove drive shaft from link shaft.

• Use the drive shaft attachment (A) [SST: KV40107500 (

—

)] and a sliding hammer (B) while inserting tip of the drive

shaft attachment between housing assembly and link shaft
assembly.

CAUTION:

Never place drive shaft joint at an extreme angle when
removing drive shaft. Also be careful not to overextend
slide joint.

12. Remove bearing housing mounting bolts.

13. Remove link shaft assembly from support bearing bracket.

14. Remove support bearing bracket, follow the procedure

described below.

Remove front exhaust tube. Refer to

EX-5, "Exploded View"

Remove three way catalyst (bank 1) and heated oxygen sensor harness bracket. Refer to

EM-33,

"Exploded View"

Remove support bearing bracket.

INSTALLATION

Note the following, and install in the reverse order of removal.
• Always replace differential side oil seal with new one when installing link shaft. Refer to

TM-152, "Exploded

• Place the protector (A) [SST: KV38107900 (

—

)] onto transaxle

assembly to prevent damage to the oil seal while inserting link
shaft. Slide link shaft sliding joint and tap with a hammer to install
securely.

• Install support bearing bracket (1) in following procedure,
- Temporarily tighten mounting bolts (A), then tighten them to speci-

fied torque.

- Temporarily tighten mounting bolts (B), then tighten them to speci-

fied torque.

• Apply NISSAN genuine grease to drive shaft serration (link shaft side), and install drive shaft onto link shaft.

• Clean the matching surface of wheel hub lock nut and wheel hub and bearing assembly.

CAUTION:

Never apply lubricating oil to these matching surface.

• Clean the matching surface of drive shaft and wheel hub and bearing assembly.

CAUTION:

JPDIF0004ZZ

JPDIF0147ZZ

JPDIF0143ZZ

Standard

: 1.5 – 2.5 g (0.053 – 0.088 oz)

Revision: 2012 October

2013 Murano CrossCabriolet

FRONT DRIVE SHAFT

FAX-19

< REMOVAL AND INSTALLATION >

FAX

Apply paste [service parts (440037S000)] to cover entire flat
surface (A) of joint sub-assembly of drive shaft.

• Never use a power tool to tighten the wheel hub lock nut.
• Perform the final tightening of each of parts under unladen condi-

tions, which were removed when removing wheel hub and bearing
assembly and axle housing.

• Never reuse cotter pin.

WHEEL SIDE

WHEEL SIDE : Disassembly and Assembly

INFOID:0000000008463530

DISASSEMBLY

Fix shaft with a vise.

CAUTION:

Protect shaft using aluminum or copper plates when fixing with a vise.

Remove boot bands, and then remove boot from joint sub-assembly.

Screw drive shaft puller (A) into joint sub-assembly screw part to
a length of 30 mm (1.18 in) or more. Support drive shaft with one
hand and pull out joint sub-assembly with a sliding hammer (B)
from housing assembly.

CAUTION:

• Align a sliding hammer and drive shaft and remove them

by pulling firmly and uniformly.

• If joint sub-assembly cannot be pulled out, try after

removing drive shaft from vehicle.

Remove circular clip (1) from housing assembly.

Remove boot from housing assembly.

ASSEMBLY

Clean the old grease on joint sub-assembly with paper waste.

Fill serration slot joint sub-assembly with NISSAN genuine grease or equivalent until the serration slot and
ball groove become full to the brim.

CAUTION:

After applying grease, use a paper waste to wipe off old grease that has oozed out.

Install boot and boot bands to housing assembly.

CAUTION:

• Wrap serration on housing assembly with tape to protect the boot from damage.
• Never reuse boot and boot band.

Remove the tape wrapped around the serration on housing assembly.

Position the circular clip on groove at the housing assembly edge.

CAUTION:

Never reuse circular clip.
NOTE:
Drive joint inserter is recommended when installing circular clip.

Align both center axles of the housing assembly edge and joint sub-assembly. Then assemble housing
assembly with circular clip joint sub-assembly.

Amount paste

: 1.0 – 3.0 g (0.04 – 0.10 oz)

JPDIG0122ZZ

JPDIF0015ZZ

Revision: 2012 October

2013 Murano CrossCabriolet

FAX-20

< REMOVAL AND INSTALLATION >

FRONT DRIVE SHAFT

Install joint sub-assembly to housing assembly using plastic
hammer.

CAUTION:

Confirm that joint sub-assembly is correctly engaged while
rotating drive housing assembly.

Apply the specified amount of grease into the boot inside from
large diameter side of boot.

Install the boot securely into grooves (indicated by “*” marks)
shown in the figure.

CAUTION:

If grease adheres to the boot mounting surface (indicated
by “*” mark) on the housing assembly or joint sub-assem-
bly, boot may be removed. Remove all grease from the boot
mounting surface.

10. To prevent the deformation of the boot, adjust the boot installa-

tion length (L) to the specified value shown below by inserting
the suitable tool into inside of the boot from the large diameter
side of the boot and discharging the inside air.

CAUTION:

• If the boot installation length exceeds the standard, it may cause breakage of boot.
• Be careful not to touch the inside of the boot with a tip of tool.

11. Secure the large and small ends of the boot with boot bands

using the boot band crimping tool (A) [SST: KV40107300 (

—

)].

CAUTION:

Never reuse boot band.

NOTE:
Secure boot band so that dimension (A) meets the specification
as shown in the figure.

12. Secure joint sub-assembly and housing assembly, and then

make sure that they are in the correct position when rotating
boot. Reinstall them using boot bands when boot installation
positions become incorrect.

CAUTION:

Never reuse boot band.

TRANSAXLE SIDE

TRANSAXLE SIDE : Disassembly and Assembly

INFOID:0000000008463531

DISASSEMBLY

Grease amount

: Refer to

RAC0049D

: Refer to

FAX-19, "WHEEL SIDE : Disassembly and Assembly"

JPDIF0222ZZ

JPDIF0012ZZ

: 7.0 mm (0.276 in) or less

JPDIF0268ZZ

Revision: 2012 October

2013 Murano CrossCabriolet

FRONT DRIVE SHAFT

FAX-21

< REMOVAL AND INSTALLATION >

FAX

Left Side

Fix drive shaft with a vise.

CAUTION:

Protect shaft using aluminum or copper plates when fixing with a vise.

Disassemble boot (wheel side). Refer to

Remove boot bands and boot (transaxle side).

Right Side

Fix drive shaft with a vise.

CAUTION:

Protect shaft using aluminum or copper plates when fixing with a vise.

Disassemble boot (wheel side). Refer to

FAX-19, "WHEEL SIDE : Disassembly and Assembly"

Remove dynamic damper, follow the procedure described below.

Remove damper bands.

Remove dynamic damper from shaft.

Remove boot bands and boot (transaxle side).

Remove dust shield from housing assembly.

Remove support bearing from link shaft, follow the procedure described below.

Press out bearing housing and support bearing from link shaft.

Remove dust shield from bearing housing.

Remove snap ring (1).

Remove oil seal.

Press out support bearing from bearing housing (1) with drift (A)
[SST: ST17130000 (

—

)]

ASSEMBLY

Left Side

Install dust shield.

CAUTION:

Never reuse dust shield.

Install circular clip.

CAUTION:

Never reuse circular clip.

Clean old grease on housing assembly with paper waste.

JPDIF0177ZZ

JPDIF0313ZZ

Revision: 2012 October

2013 Murano CrossCabriolet

FAX-22

< REMOVAL AND INSTALLATION >

FRONT DRIVE SHAFT

Install boot securely into grooves (indicated by “*” marks) shown
in the figure.

CAUTION:

If grease adheres to the boot mounting surface (indicated
by “*” mark) on housing assembly, boot may be removed.
Remove all grease from the boot mounting surface.

To prevent the deformation of the boot, adjust the boot installa-
tion length (L) to the specified value shown below by inserting
the suitable tool into the inside of boot from the large diameter
side of boot and discharging inside air.

CAUTION:

• If the boot installation length exceeds the standard, it may cause breakage of boot.
• Be careful not to touch the inside of the boot with the tip of tool.

Install boot bands securely as shown in the figure.

Put boot band in the groove on drive shaft boot. Then fit pawls
(

) into holes to temporary installation.

NOTE:
For the large diameter side, fit projection (A) and guide slit (B) at
first.

Pinch projection on the band with suitable pliers to tighten band.

Insert tip of band below end of the pawl.

Secure housing assembly, and then make sure that they are in
the correct position when rotating boot. Reinstall them with boot
bands when the mounting positions become incorrect.

Right Side

Install support bearing from link shaft, follow the procedure described below.

Press support bearing to bearing housing (1) with drift (A) [SST:
ST35271000 (J-26091)]

: Refer to

FAX-19, "WHEEL SIDE : Disassembly and Assembly"

JPDIF0144ZZ

JPDIF0157ZZ

JPDIF0158ZZ

JPDIF0314ZZ

Revision: 2012 October

2013 Murano CrossCabriolet

FRONT DRIVE SHAFT

FAX-23

< REMOVAL AND INSTALLATION >

FAX

Install snap ring (1).

CAUTION:

Never reuse snap ring.

Install dust shield to baring housing.

CAUTION:

Never reuse dust shield.

Install oil seal to bearing housing with drift [SST: ST35271000
(J-26091)].

CAUTION:

• Never reuse oil seal.
• Apply multi - purpose grease to oil seal lip.

Press bearing housing assembly to link shaft.

Install circular clip to link shaft.

CAUTION:

Never reuse circular clip.

Clean old grease on housing assembly with paper waste.

Install boot securely into grooves (indicated by “*” marks) shown
in the figure.

CAUTION:

If grease adheres to the boot mounting surface (indicated
by “*” mark) on housing assembly, boot may be removed.
Remove all grease from the boot mounting surface.

CAUTION:

• If the boot installation length exceeds the standard, it may cause breakage of boot.
• Be careful not to touch the inside of the boot with the tip of tool.

Install boot bands securely as shown in the figure.

Put boot band in the groove on drive shaft boot. Then fit pawls
(

) into holes to temporary installation.

NOTE:
For the large diameter side, fit projection (A) and guide slit (B) at
first.

Pinch projection on the band with suitable pliers to tighten band.

Insert tip of band below end of the pawl.

Secure housing assembly, and then make sure that they are in
the correct position when rotating boot. Reinstall them with boot
bands when the mounting positions become incorrect.

Assemble boot (wheel side) and joint sub-assembly. Refer to

Install dynamic damper, follow the procedure described below.

Install dynamic damper to shaft.

: Refer to

FAX-24, "Inspection"

JPDIF0177ZZ

JPDIF0144ZZ

JPDIF0157ZZ

JPDIF0158ZZ

Revision: 2012 October

2013 Murano CrossCabriolet

FAX-24

< REMOVAL AND INSTALLATION >

FRONT DRIVE SHAFT

Secure dynamic damper with bands in the following specified
position (A) when installing.

CAUTION:

Never reuse bands.

Inspection

INFOID:0000000008463532

INSPECTION AFTER REMOVAL

• Move joint up/down, left/right, and in the axial directions. Check for motion that is not smooth and for signifi-

cant looseness.

• Check boot for cracks, damage, and leakage of grease.
• Disassemble drive shaft and exchange malfunctioning part if there

is a non-standard condition.

INSPECTION AFTER DISASSEMBLY

Shaft

Check shaft for runout, cracks, or other damage. Replace if necessary.

Dynamic Damper

Check damper for cracks or wear. Replace if necessary.

Joint Sub-Assembly (Wheel Side)

Check the following:
• Joint sub-assembly for rough rotation and excessive axial looseness.
• The inside of the joint sub-assembly for entry of foreign material.
• Joint sub-assembly for compression scars, cracks, and fractures inside of joint sub-assembly.
Replace joint sub-assembly if there are any non-standard conditions of components.

Housing Assembly (Transaxle Side)

Replace housing assembly if there is scratching or wear of housing assembly roller contact surface.

Link Shaft (Right side)

Check shaft for runout, cracks, or other damage. Replace if necessary.

Support Bearing (Right Side)

Make sure wheel bearing rolls freely and is free from noise, cracks, pitting or wear. Replace support bearing if
there are any non-standard conditions.

Support Bearing Bracket (Right Side)

Check for bending, cracks, or damage. Replace support bearing bracket if there are any non-standard condi-
tions.

: Refer to