Nissan Murano Z51 (2008 year). Manual - part 63

AV

GPS ANTENNA

AV-781

< ON-VEHICLE REPAIR >

[BOSE AUDIO WITH NAVIGATION]

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

Removal and Installation

INFOID:0000000003356734

REMOVAL

1.

Remove combination meter. Refer to 

MWI-145, "Exploded View"

.

2.

Disconnect GPS antenna connector from AV control unit.

3.

Remove GPS antenna (1) from instrument panel.

INSTALLATION

Install in the reverse order of removal.

JPNIA0804ZZ

Revision: 2008 October

2009 Murano

AV-782

< ON-VEHICLE REPAIR >

[BOSE AUDIO WITH NAVIGATION]

CAMERA CONTROL UNIT

CAMERA CONTROL UNIT

Exploded View

INFOID:0000000003356735

Removal and Installation

INFOID:0000000003356736

REMOVAL

1.

Remove luggage side finisher lower (RH). Refer to 

INT-33, "Exploded View"

.

2.

Remove camera control unit screws, disconnect camera control unit connector and remove the camera
control unit.

INSTALLATION

Install in the reverse order of removal.

Adjustment

INFOID:0000000003356737

ADJUSTMENT

There may be a misalignment of possible route line center position of rear view monitor after removing camera
control unit. Therefore, correct neutral position with the following procedure.

1.

Steer the steering wheel to the leftmost and rightmost ends.

2.

Drive vehicle at 30 km/h (18.6 MPH) min. speed at least 100 m (328.1 ft).

JPNIA0796ZZ

1.

Camera control unit

Revision: 2008 October

2009 Murano

AV

REAR VIEW CAMERA

AV-783

< ON-VEHICLE REPAIR >

[BOSE AUDIO WITH NAVIGATION]

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

REAR VIEW CAMERA

Exploded View

INFOID:0000000003356738

REMOVAL

Refer to 

INT-37, "Exploded View"

.

DISASSEMBLY

Removal and Installation

INFOID:0000000003356739

REMOVAL

1.

Remove back door finisher inner. Refer to 

INT-37, "Exploded View"

.

2.

Remove finisher.

3.

Remove rear view camera screws, disconnect rear view camera connector and remove rear view camera
from back door assembly.

INSTALLATION

Install in the reverse order of removal.

Adjustment

INFOID:0000000003356740

Adjust the guide line position if the guide line position is shifted after installing the rear view camera.

1.

Rear view camera

2.

Finisher

JPNIA0797ZZ

Revision: 2008 October

2009 Murano

AV-784

< ON-VEHICLE REPAIR >

[BOSE AUDIO WITH NAVIGATION]

REAR VIEW CAMERA

1.

Draw lines on rearward area of the vehicle passing through the
following points: 200 mm (7.87 in) from both sides of the vehicle,
and 0.5 m (1.64 ft), 1.0 m (3.28 ft) from the rear end of the
bumper.

2.

Set into “Adjust offset of rear view camera” mode of Confirma-
tion / Adjustment mode.

3.

Rotate the center dial, and then select the guiding line pattern so
that its angle is aligned with the correction line of the rear of the
vehicle.

4.

Make fine adjustment to the correction line of the rear of the
vehicle with up/down/left/right switches so that its position is
aligned with the guiding line. Press “OK” switch and record the
adjusted guiding line position to the camera control unit.

CAUTION:

Never operate other function such as pressing BACK while writing index data.
If Confirmation/Adjustment mode does not function in the above procedure, perform one of the
following service to adjust the index again.
• Remove battery for five min. Then reconnect battery.
• Remove camera control unit connector for five min. Then reconnect camera control unit connec-

tor.

SKIB3691E

Selected pattern

: 7

Up/Down adjustment range

: 

−

20 – 20

Left/Right adjustment range

: 

−

20 – 20

SKIB3689E

Revision: 2008 October

2009 Murano

AV

STEERING ANGLE SENSOR

AV-785

< ON-VEHICLE REPAIR >

[BOSE AUDIO WITH NAVIGATION]

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

STEERING ANGLE SENSOR

Exploded View

INFOID:0000000003356741

REMOVAL

Refer to 

ST-15, "Exploded View"

.

DISASSEMBLY

Removal and Installation

INFOID:0000000003356742

REMOVAL

1.

Remove spiral cable. 

2.

Remove steering angle sensor from spiral cable.

INSTALLATION

Install in the reverse order of removal.

JSNIA0135ZZ

1.

Spiral cable

2.

Steering angle sensor

Revision: 2008 October

2009 Murano

AV-786

< ON-VEHICLE REPAIR >

[BOSE AUDIO WITH NAVIGATION]

ROOF ANTENNA

ROOF ANTENNA

Exploded View

INFOID:0000000003356716

Refer to 

GI-4, "Components"

 for symbols in the figure.

Removal and Installation

INFOID:0000000003356717

REMOVAL

1.

Remove headlining assembly (rear) to secure work space between vehicle and headlining. Refer to 

INT-

25, "NORMAL ROOF : Exploded View"

 [without sunroof] or 

INT-29, "SUNROOF : Exploded View"

 [with

sunroof].

2.

Disconnect AM/FM main connector and satellite radio antenna connector.

3.

Remove antenna base & satellite radio nut, and then remove antenna base &satellite radio antenna from
roof panel.

INSTALLATION

Install in the reverse order of removal.

CAUTION:

When Antenna base & satellite radio antenna mounting nut tightening torque is loose, be careful
about tightening torque. Antenna sensitivity becomes poor, and when it is excessive, roof panel may
become deformed.

JPNIA0786ZZ

1.

Rod antenna

2.

Antenna bade & satellite radio an-
tenna

Antenna base & satellite ra-
dio antenna mounting nut 

: 6.5 N·m (0.66 kg-m, 58 in-lb)

Revision: 2008 October

2009 Murano

AV

ANTENNA FEEDER (RADIO)

AV-787

< ON-VEHICLE REPAIR >

[BOSE AUDIO WITH NAVIGATION]

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

ANTENNA FEEDER (RADIO)

Harness Layout

INFOID:0000000003356744

JPNIA0803GB

Revision: 2008 October

2009 Murano

AV-788

< ON-VEHICLE REPAIR >

[BOSE AUDIO WITH NAVIGATION]

ANTENNA FEEDER (SATELLITE RADIO)

ANTENNA FEEDER (SATELLITE RADIO)

Harness Layout

INFOID:0000000003507978

JPNIA0803GB

Revision: 2008 October

2009 Murano

AV

ANTENNA FEEDER (GPS)

AV-789

< ON-VEHICLE REPAIR >

[BOSE AUDIO WITH NAVIGATION]

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

ANTENNA FEEDER (GPS)

Harness Layout

INFOID:0000000003507979

JPNIA0803GB

Revision: 2008 October

2009 Murano

BCS

BCS-1

ELECTRICAL & POWER CONTROL

C

D

E

F

G

H

I

J

K

L

B

SECTION 

BCS

A

O

P

N

CONTENTS

BODY CONTROL SYSTEM

BASIC INSPECTION  ....................................

3

INSPECTION AND ADJUSTMENT .....................

3

ADDITIONAL SERVICE WHEN REPLACING 
CONTROL UNIT (BCM) ...............................................

3

ADDITIONAL SERVICE WHEN REPLACING 
CONTROL UNIT (BCM) : Description  .......................

3

ADDITIONAL SERVICE WHEN REPLACING 
CONTROL UNIT (BCM) : Special Repair Require-
ment ..........................................................................

3

CONFIGURATION (BCM)  ...........................................

3

CONFIGURATION (BCM) : Description ....................

3

CONFIGURATION (BCM) : Special Repair Re-
quirement ..................................................................

4

CONFIGURATION (BCM) : Configuration list  ...........

5

FUNCTION DIAGNOSIS ...............................

7

BODY CONTROL SYSTEM ................................

7

System Description  ...................................................

7

Component Parts Location ........................................

8

COMBINATION SWITCH READING SYSTEM 

.....

9

System Diagram ........................................................

9

System Description  ...................................................

9

Component Parts Location ......................................

12

SIGNAL BUFFER SYSTEM  ...............................

13

System Diagram ......................................................

13

System Description  .................................................

13

POWER CONSUMPTION CONTROL SYS-
TEM ....................................................................

14

System Diagram ......................................................

14

System Description  .................................................

14

Component Parts Location ......................................

16

DIAGNOSIS SYSTEM (BCM)  ............................

17

COMMON ITEM  .........................................................

17

COMMON ITEM : CONSULT-III Function (BCM - 
COMMON ITEM)  .....................................................

17

DOOR LOCK ..............................................................

18

DOOR LOCK : CONSULT-III Function (BCM - 
DOOR LOCK) ..........................................................

18

REAR WINDOW DEFOGGER  ...................................

20

REAR WINDOW DEFOGGER : CONSULT-III 
Function (BCM - REAR DEFOGGER) .....................

20

BUZZER .....................................................................

20

BUZZER : CONSULT-III Function (BCM - BUZZ-
ER) ..........................................................................

20

INT LAMP ...................................................................

21

INT LAMP : CONSULT-III Function (BCM - INT 
LAMP) ......................................................................

21

MULTI REMOTE ENT  ................................................

22

MULTI REMOTE ENT : CONSULT-III Function 
(BCM - MULTI REMOTE ENT) ................................

22

HEADLAMP ...............................................................

24

HEADLAMP : CONSULT-III Function (BCM - 
HEAD LAMP) ...........................................................

24

WIPER ........................................................................

26

WIPER : CONSULT-III Function (BCM - WIPER) ....

26

FLASHER ...................................................................

27

FLASHER : CONSULT-III Function (BCM - 
FLASHER) ...............................................................

27

INTELLIGENT KEY ....................................................

28

INTELLIGENT KEY : CONSULT-III Function 
(BCM - INTELLIGENT KEY) ....................................

28

COMB SW ..................................................................

31

COMB SW : CONSULT-III Function (BCM - 
COMB SW) ..............................................................

31

BCM ...........................................................................

32

BCM : CONSULT-III Function (BCM - BCM) ...........

32

Revision: 2008 October

2009 Murano

BCS-2

IMMU .........................................................................

32

IMMU : CONSULT-III Function (BCM - IMMU) .......

32

BATTERY SAVER  ....................................................

33

BATTERY SAVER : CONSULT-III Function (BCM 
- BATTERY SAVER)  ..............................................

33

TRUNK ......................................................................

34

TRUNK : CONSULT-III Function (BCM - TRUNK) ...

34

THEFT ALM  ..............................................................

35

THEFT ALM : CONSULT-III Function (BCM - 
THEFT) ...................................................................

35

RETAINED PWR  .......................................................

36

RETAINED PWR : CONSULT-III Function (BCM - 
RETAINED PWR)  ...................................................

36

SIGNAL BUFFER ......................................................

36

SIGNAL BUFFER : CONSULT-III Function (BCM 
- SIGNAL BUFFER) ................................................

36

AIR PRESSURE MONITOR ......................................

37

AIR PRESSURE MONITOR : Diagnosis Descrip-
tion ..........................................................................

37

AIR PRESSURE MONITOR : CONSULT-III Func-
tion (BCM - AIR PRESSURE MONITOR) ...............

38

COMPONENT DIAGNOSIS  ........................

40

U1000 CAN COMM CIRCUIT  ............................

40

Description ..............................................................

40

DTC Logic ...............................................................

40

Diagnosis Procedure  ..............................................

40

U1010 CONTROL UNIT (CAN)  .........................

41

DTC Logic ...............................................................

41

Diagnosis Procedure  ..............................................

41

U0415 VEHICLE SPEED SIG  ............................

42

Description ..............................................................

42

DTC Logic ...............................................................

42

Diagnosis Procedure  ..............................................

42

B2562 LOW VOLTAGE .....................................

43

DTC Logic  ...............................................................

43

Diagnosis Procedure ...............................................

43

POWER SUPPLY AND GROUND CIRCUIT  .....

44

Diagnosis Procedure ...............................................

44

COMBINATION SWITCH INPUT CIRCUIT  .......

45

Diagnosis Procedure ...............................................

45

COMBINATION SWITCH OUTPUT CIRCUIT ...

47

Diagnosis Procedure ...............................................

47

ECU DIAGNOSIS  .......................................

49

BCM (BODY CONTROL MODULE)  ..................

49

Reference Value  .....................................................

49

Wiring Diagram - BCM - ..........................................

73

Fail-safe ..................................................................

87

DTC Inspection Priority Chart ...............................

90

DTC Index ..............................................................

91

SYMPTOM DIAGNOSIS  ............................

94

COMBINATION SWITCH SYSTEM SYMP-
TOMS .................................................................

94

Symptom Table .......................................................

94

PRECAUTION ............................................

95

PRECAUTIONS  .................................................

95

Precaution for Supplemental Restraint System 
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" .................................................................

95

ON-VEHICLE REPAIR  ...............................

96

BCM (BODY CONTROL MODULE)  ..................

96

Exploded View  ........................................................

96

Removal and Installation .........................................

96

COMBINATION SWITCH  ..................................

97

Exploded View  ........................................................

97

Removal and Installation .........................................

97

Revision: 2008 October

2009 Murano

BCS

INSPECTION AND ADJUSTMENT

BCS-3

< BASIC INSPECTION >

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

BASIC INSPECTION

INSPECTION AND ADJUSTMENT

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (BCM)

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (BCM) : Description

INFOID:0000000003486680

BEFORE REPLACEMENT

When replacing BCM, save or print current vehicle specification with CONSULT-III configuration before
replacement.
NOTE:
If “READ CONFIGURATION” can not be used, use the “WRITE CONFIGURATION - Manual selection” after
replacing BCM.

AFTER REPLACEMENT

CAUTION:

• When replacing BCM, you must perform “WRITE CONFIGURATION” with CONSULT-III.
- Complete the procedure of “WRITE CONFIGURATION” in order.
- If you set incorrect “WRITE CONFIGURATION”, incidents might occur.
- Configuration is different for each vehicle model. Confirm configuration of each vehicle model.
• When replacing BCM, perform the system initialization (NATS).

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (BCM) : Special Repair 
Requirement

INFOID:0000000003486681

1.

SAVING VEHICLE SPECIFICATION

CONSULT-III Configuration

Perform “READ CONFIGURATION” to save or print current vehicle specification. Refer to 

BCS-3, "CONFIGU-

RATION (BCM) : Description"

.

NOTE:
If “READ CONFIGURATION” can not be used, use the “WRITE CONFIGURATION - Manual selection” after
replacing BCM.

>> GO TO 2.

2.

REPLACE BCM

Replace BCM. Refer to 

BCS-96, "Exploded View"

.

>> GO TO 3.

3.

WRITING VEHICLE SPECIFICATION

CONSULT-III Configuration

Perform “WRITE CONFIGURATION - Config file” or “WRITE CONFIGURATION - Manual selection” to write
vehicle specification. Refer to 

BCS-4, "CONFIGURATION (BCM) : Special Repair Requirement"

.

>> GO TO 4.

4.

INITIALIZE BCM (NATS)

Perform BCM initialization. (NATS)

>> WORK END

CONFIGURATION (BCM)

CONFIGURATION (BCM) : Description

INFOID:0000000003486682

Vehicle specification needs to be written with CONSULT-III because it is not written after replacing BCM.

Revision: 2008 October

2009 Murano

BCS-4

< BASIC INSPECTION >

INSPECTION AND ADJUSTMENT

Configuration has three functions as follows

NOTE:

Manual setting item: Items which need selection by vehicle specifications

Automatic setting item: Items which are written in automatically (Setting can not be changed)

CAUTION:

• When replacing BCM, you must perform “WRITE CONFIGURATION” with CONSULT-III.
• Complete the procedure of “WRITE CONFIGURATION” in order.
• If you set incorrect “WRITE CONFIGURATION”, incidents might occur.
• Configuration is different for each vehicle model. Confirm configuration of each vehicle model.
• Never perform “WRITE CONFIGURATION” except for new BCM. 

CONFIGURATION (BCM) : Special Repair Requirement

INFOID:0000000003486683

1.

WRITING MODE SELECTION

CONSULT-III Configuration

Select “CONFIGURATION” of BCM.

When writing saved data>>GO TO 2.
When writing manually>>GO TO 3.

2.

PERFORM “WRITE CONFIGURATION - CONFIG FILE”

CONSULT-III Configuration

Perform “WRITE CONFIGURATION - Config file”.

>> WORK END

3.

PERFORM “WRITE CONFIGURATION - MANUAL SELECTION”

CONSULT-III Configuration

1.

Select “WRITE CONFIGURATION - Manual selection”.

2.

Identify the correct model and configuration list. Refer to 

BCS-5, "CONFIGURATION (BCM) : Configura-

tion list"

.

3.

Confirm and/or change setting value for each item.

CAUTION:

Thoroughly read and understand the vehicle specification. Incorrect settings may result in abnor-
mal control of ECU.

4.

Select “SETTING”.

CAUTION:

Make sure to select “SETTING” even if the indicated configuration of brand new BCM is same as
the desirable configuration. If not, configuration which is set automatically by selecting vehicle
model can not be memorized.

5.

When “COMMAND FINISHED”, select “END”.

>> GO TO 4.

4.

OPERATION CHECK

Confirm that each function controlled by BCM operates normally.

>> WORK END

Function

Description

READ CONFIGURATION

• Reads the vehicle configuration of current BCM.
• Saves the read vehicle configuration.

WRITE CONFIGURATION - Manual selection

Writes the vehicle configuration with manual selection.

WRITE CONFIGURATION - Config file

Writes the vehicle configuration with saved data.

Revision: 2008 October

2009 Murano

BCS

INSPECTION AND ADJUSTMENT

BCS-5

< BASIC INSPECTION >

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

CONFIGURATION (BCM) : Configuration list

INFOID:0000000003486684

CAUTION:

Thoroughly read and understand the vehicle specification. Incorrect settings may result in abnormal
control of ECU.

EXCEPT FOR MEXICO

⇔

: Items which confirm vehicle specifications

FOR MEXICO

MANUAL SETTING ITEM

NOTE

Items

Setting value

AUTO LIGHT

WITH 

⇔

 WITHOUT

—

DTRL

WITH 

⇔

 WITHOUT

• WITH: With daytime running light system
• WITHOUT: Without daytime running light system

AV C/U

WITH 

⇔

 WITHOUT

—

AUTO BACK DOOR

WITH 

⇔

 WITHOUT

—

THEFT ALM AREA

WITHOUT 

⇔

 MODE2

• WITHOUT: Without vehicle security system
• MODE2: With vehicle security system

I-KEY

WITH 

⇔

 WITHOUT

—

RAIN SENSOR

WITH 

⇔

 WITHOUT

—

Key Fob Type

MODE7 

⇔

 MODE9

• MODE7: With automatic back door system
• MODE9: Without automatic back door system

AUTO SETTING ITEM

NOTE

Items

Setting value

H/L BULB

DEFAULT

—

FR FOG LAMP

WITH

—

RR FOG LAMP

WITH

Even on a vehicle without rear fog lamp. It displays “WITH”.

TRANSMISSION

AT with ABS

—

TPMS WITH

—

TIRE PRESSURE

230kPa

—

TR OPEN SW (INT)

MODE1

—

FOG LAMP BULB

SINGLE BULB

—

DI LMP VARIAT

MODE2

—

LIGHT RECOG

MODE4

RR WIPER GND

MODE1

—

HAZARD SW TYPE

MODE1

—

BCM AC CONTROL

MODE1

—

Trunk/Glass Hatch select

Glass Hatch

Even on a vehicle without glass hatch. It displays “Glass 
Hatch”.

WELCOME LIGHT SELECT

WITHOUT

—

WELCOME LIGHT TIMER

MODE1

—

REAR WIPER

WITH

—

TRUNK ACT OUTPUT

MODE2

—

RAIN SEN TYPE

MODE2

—

DROP WIP FUNCTION

WITHOUT

—

WELCOME LIGHT TIMER2

MODE1

—

Revision: 2008 October

2009 Murano

BCS-6

< BASIC INSPECTION >

INSPECTION AND ADJUSTMENT

⇔

: Items which confirm vehicle specifications

MANUAL SETTING ITEM

NOTE

Items

Setting value

AUTO LIGHT

WITH 

⇔

 WITHOUT

—

DTRL

WITHOUT

—

AV C/U

WITH 

⇔

 WITHOUT

—

AUTO BACK DOOR

WITH 

⇔

 WITHOUT

—

THEFT ALM AREA

WITHOUT 

⇔

 MODE2

• WITHOUT: Without vehicle security system
• MODE2: With vehicle security system

HAZARD SW TYPE

MODE1

—

I-KEY

WITH 

⇔

 WITHOUT

—

RAIN SENSOR

WITH 

⇔

 WITHOUT

—

Key Fob Type

MODE7 

⇔

 MODE9

• MODE7: With automatic back door system
• MODE9: Without automatic back door system

AUTO SETTING ITEM

NOTE

Items

Setting value

H/L BULB

DEFAULT

—

FR FOG LAMP

WITH

—

RR FOG LAMP

WITH

Even on a vehicle without rear fog lamp. It displays “WITH”.

TRANSMISSION

AT with ABS

—

TPMS WITHOUT

—

TR OPEN SW (INT)

MODE1

—

FOG LAMP BULB

SINGLE BULB

—

DI LMP VARIAT

MODE2

—

LIGHT RECOG

MODE4

RR WIPER GND

MODE1

—

BCM AC CONTROL

MODE1

—

Trunk/Glass Hatch select

Glass Hatch

Even on a vehicle without glass hatch. It displays “Glass 
Hatch”.

WELCOME LIGHT SELECT

WITHOUT

—

WELCOME LIGHT TIMER

MODE1

—

REAR WIPER

WITH

—

TRUNK ACT OUTPUT

MODE2

—

RAIN SEN TYPE

MODE2

—

DROP WIP FUNCTION

WITHOUT

—

WELCOME LIGHT TIMER2

MODE1

—

Revision: 2008 October

2009 Murano

BCS

BODY CONTROL SYSTEM

BCS-7

< FUNCTION DIAGNOSIS >

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

FUNCTION DIAGNOSIS

BODY CONTROL SYSTEM

System Description

INFOID:0000000003441350

OUTLINE

• BCM (Body Control Module) controls the various electrical components. It inputs the information required to

the control from CAN communication and the signal received from each switch and sensor. 

• BCM has combination switch reading function for reading the operation status of combination switches (light,

turn signal, wiper and washer) in addition to a function for controlling the operation of various electrical com-
ponents. It also has the signal transmission function as the passed point of signal and the power saving con-
trol function that reduces the power consumption with the ignition switch OFF.

• BCM is equipped with the diagnosis function that performs the diagnosis with CONSULT-III and various set-

tings.

BCM CONTROL FUNCTION LIST

System

Reference

Combination switch reading system

BCS-9, "System Diagram"

Signal buffer system

BCS-13, "System Diagram"

Power consumption control system

BCS-14, "System Diagram"

Auto light system

EXL-13, "System Diagram"

Turn signal and hazard warning lamp system

•

EXL-17, "System Diagram"

 (Xenon type headlamp)

•

EXL-197, "System Diagram"

 (Halogen type headlamp)

Headlamp system

•

EXL-8, "System Diagram"

 (Xenon type headlamp)

•

EXL-191, "System Diagram"

 (Halogen type headlamp)

Parking, license plate and tail lamps system

•

EXL-19, "System Diagram"

 (Xenon type headlamp)

•

EXL-199, "System Diagram"

 (Halogen type headlamp)

Front fog lamp system

•

EXL-15, "System Diagram"

 (Xenon type headlamp)

•

EXL-195, "System Diagram"

 (Halogen type headlamp)

Exterior lamp battery saver system

•

EXL-21, "System Diagram"

 (Xenon type headlamp)

•

EXL-201, "System Diagram"

 (Halogen type headlamp)

Daytime running light system

•

EXL-11, "System Diagram"

 (Xenon type headlamp)

•

EXL-193, "System Diagram"

 (Halogen type headlamp)

Interior room lamp control system

INL-5, "System Diagram"

Step lamp system

Interior room lamp battery saver system

INL-8, "System Diagram"

Front wiper and washer system

•

WW-5, "WITH RAIN SENSOR : System Diagram"

 (With rain 

sensor)

•

WW-9, "WITHOUT RAIN SENSOR : System Diagram"

 (With-

out rain sensor)

Rear wiper and washer system

WW-14, "System Diagram"

Warning chime system

WCS-5, "WARNING CHIME SYSTEM : System Diagram"

Door lock system

•

DLK-18, "System Diagram"

 (With Intelligent Key system)

•

DLK-388, "System Diagram"

 (Without Intelligent Key system)

Back door opener system (Without Intelligent Key system)

DLK-396, "System Diagram"

Automatic back door system

DLK-48, "System Diagram"

Automatic drive positioner system

ADP-13, "AUTOMATIC DRIVE POSITIONER SYSTEM : System 
Diagram"

Nissan Vehicle Immobilizer System (NVIS) - NATS (With Intelligent 
Key system)

SEC-18, "System Diagram"

Revision: 2008 October

2009 Murano