Nissan Juke (2016 year). Service Repair Manual - part 346

EX-2

< PRECAUTION >

[MR16DDT ]

PRECAUTIONS

PRECAUTION

PRECAUTIONS

Precautions for Removing Battery Terminal

INFOID:0000000012197609

•  When removing the 12V battery terminal, turn OFF the ignition

switch and wait at least 30 seconds.

NOTE:

ECU may be active for several tens of seconds after the ignition

switch is turned OFF. If the battery terminal is removed before ECU

stops, then a DTC detection error or ECU data corruption may

occur.

•  For vehicles with the 2-batteries, be sure to connect the main bat-

tery and the sub battery before turning ON the ignition switch.

NOTE:

If the ignition switch is turned ON with any one of the terminals of

main battery and sub battery disconnected, then DTC may be

detected.

•  After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.

NOTE:

The removal of 12V battery may cause a DTC detection error.

Removal and Installation

INFOID:0000000012197610

CAUTION:

• Be sure to use genuine exhaust system parts or equivalents which are specially designed for heat

resistance, corrosion resistance, and shape.

• Perform the operation with the exhaust system fully cooled down because the system will be hot

just after engine stops. 

• Be careful not to cut your hand on the heat insulator edge.

SEF289H

Revision: November 2015

2016 JUKE

PREPARATION

EX-3

< PREPARATION >

[MR16DDT ]

C

D

E

F

G

H

I

J

K

L

M

A

EX

N

P

O

PREPARATION

PREPARATION

Special Service Tools

INFOID:0000000012197611

The actual shapes of TechMate tools may differ from those of special service tools illustrated here.

Commercial Service Tools

INFOID:0000000012197612

Tool number
(TechMate No.)
Tool name

Description

KV10114400
(J-38365)
Heated oxygen sensor wrench

Loosening or tightening heated oxygen sen-
sor 2 ( 2WD models)

a: For 22 mm (0.87 in) width hexagon nut

S-NT636

Tool name

Description

Power tool

Loosening nuts and bolts

Heated oxygen sensor thread cleaner

Reconditioning the exhaust system threads 
before installing a new heated oxygen sensor 
(Use with anti-seize lubricant shown below.)

A: J-43897-18 [18 mm (0.71 in) dia.] for zir-
conia heated oxygen sensor
B: J-43897-12 [12 mm (0.47 in) dia.] for tita-
nia heated oxygen sensor
C: Mating surface shave cylinder
D: Flutes

Anti-seize lubricant (Permatex 133AR 
or equivalent meeting MIL specifica-
tion MIL-A-907)

Lubricating heated oxygen sensor thread 
cleaner when reconditioning exhaust system 
threads

PBIC0190E

JPBIA0238ZZ

AEM489

Revision: November 2015

2016 JUKE

EX-4

< PERIODIC MAINTENANCE >

[MR16DDT ]

EXHAUST SYSTEM

PERIODIC MAINTENANCE

EXHAUST SYSTEM

Inspection

INFOID:0000000012197613

Check exhaust pipes, muffler, and mounting for improper attach-

ment, leakage, cracks, damage or deterioration.

• If anything is found, repair or replace damaged parts.

SMA211A

Revision: November 2015

2016 JUKE

EXHAUST SYSTEM

EX-5

< REMOVAL AND INSTALLATION >

[MR16DDT ]

C

D

E

F

G

H

I

J

K

L

M

A

EX

N

P

O

REMOVAL AND INSTALLATION

EXHAUST SYSTEM

Exploded View

INFOID:0000000012197614

2WD (Standard models)

JSBIA3454GB

1.

Center muffler

2.

Mounting rubber

3.

Spring

4.

Seal bearing

5.

Stud bolt

6.

Exhaust front tube

7.

Heated oxygen sensor 2

8.

Seal bearing

9.

Ring gasket

10. Main muffler
A.

To catalyst convertor

 : N·m (kg-m, ft-lb)

 : Always replace after every disassembly.

Revision: November 2015

2016 JUKE

EX-6

< REMOVAL AND INSTALLATION >

[MR16DDT ]

EXHAUST SYSTEM

2WD (NISMO models)

JPBIA7035GB

1.

Center muffler

2.

Mounting rubber

3.

Spring

4.

Seal bearing

5.

Stud bolt

6.

Exhaust front tube

7.

Heated oxygen sensor 2

8.

Seal bearing

9.

Ring gasket

10. Main muffler
A.

To catalyst convertor

 : N·m (kg-m, ft-lb)

 : Always replace after every disassembly.

Revision: November 2015

2016 JUKE

EXHAUST SYSTEM

EX-7

< REMOVAL AND INSTALLATION >

[MR16DDT ]

C

D

E

F

G

H

I

J

K

L

M

A

EX

N

P

O

2WD (NISMO RS models)

JSBIA4459GB

1.

Center tube

2.

Mounting rubber

3.

Spring

4.

Seal bearing

5.

Stud bolt

6.

Exhaust front tube

7.

Heated oxygen sensor 2

8.

Seal bearing

9.

Ring gasket

10. Main muffler
A.

To catalyst convertor

 : N·m (kg-m, ft-lb)

 : Always replace after every disassembly.

Revision: November 2015

2016 JUKE

EX-8

< REMOVAL AND INSTALLATION >

[MR16DDT ]

EXHAUST SYSTEM

AWD (Standard models)

JSBIA3455GB

1.

Center muffler

2.

Mounting rubber

3.

Spring

4.

Seal bearing

5.

Stud bolt

6.

Exhaust front tube

7.

Seal bearing

8.

Ring gasket

9.

Main muffler

A.

To catalyst convertor

 : N·m (kg-m, ft-lb)

 : Always replace after every disassembly.

Revision: November 2015

2016 JUKE

EXHAUST SYSTEM

EX-9

< REMOVAL AND INSTALLATION >

[MR16DDT ]

C

D

E

F

G

H

I

J

K

L

M

A

EX

N

P

O

AWD (NISMO models)

JSBIA3379GB

1.

Center muffler

2.

Mounting rubber

3.

Spring

4.

Seal bearing

5.

Stud bolt

6.

Exhaust front tube

7.

Seal bearing

8.

Ring gasket

9.

Main muffler

A.

To catalyst convertor

 : N·m (kg-m, ft-lb)

 : Always replace after every disassembly.

Revision: November 2015

2016 JUKE