Mitsubishi Outlander (2013+). Manual - part 531

 

  Index      Mitsubishi     Mitsubishi Outlander - service repair manual 2013 year

 

Search            

 

 

 

 

 

 

 

  

 

Content   ..  529  530  531  532   ..

 

 

Mitsubishi Outlander (2013+). Manual - part 531

 

 

SUNROOF ASSEMBLY

BODY

42A-144

6039

S/R Log2 IG-SW

The ignition switch was turned OFF the 
last time but one.

OFF

The ignition switch was turned ON the last 
time but one.

ON

6040

S/R Log2 Motor actuate

The motor did not operate the last time but 
one.

OFF

The motor operated the last time but one.

ON

6041

S/R Log2 Operation

Sunroof operation permission status was 
"not permitted" the last time but one.

OFF

Sunroof operation permission status was 
"permitted" the last time but one.

ON

6042

S/R Log3(Trigger) Open

The open switch was not operated the last 
time but two.

OFF

The open switch was operated the last 
time but two.

ON

6043

S/R Log3(Trigger) Close

The close switch was not operated the last 
time but two.

OFF

The close switch was operated the last 
time but two.

ON

6044

S/R Log3(Trigger) Tilt Up

The close switch was not operated the last 
time but two.

OFF

The close switch was operated the last 
time but two.

ON

6045

S/R Log3(Trigger) Multi 
Close

The multi-close function was not operated 
the last time but two.

OFF

The multi-close function was operated the 
last time but two.

ON

6046

S/R Log3(Trigger) Overload Overload was not detected the last time 

but two.

OFF

Overload was detected the last time but 
two.

ON

6047

S/R Log3 IG-SW

The ignition switch was turned OFF the 
last time but two.

OFF

The ignition switch was turned ON the last 
time but two.

ON

6048

S/R Log3 Motor actuate

The motor did not operate the last time but 
two.

OFF

The motor operated the last time but two.

ON

6049

S/R Log3 Operation

Sunroof operation permission status was 
"not permitted" the last time but two.

OFF

Sunroof operation permission status was 
"permitted" the last time but two.

ON

Item No. M.U.T.-III display

Check condition

Normal condition

SUNROOF ASSEMBLY

BODY

42A-145

TROUBLE SYMPTOM CHART

M1426002000620

CAUTION

During diagnosis, a diagnosis code associated with other system may be set when the ignition switch 
is turned on with connector(s) disconnected. On completion, confirm all systems for diagnosis 
code(s). If diagnosis code(s) are set, erase them all.

6050

S/R Log4(Trigger) Open

The open switch was not operated the last 
time but three.

OFF

The open switch was operated the last 
time but three.

ON

6051

S/R Log4(Trigger) Close

The close switch was not operated the last 
time but three.

OFF

The close switch was operated the last 
time but three.

ON

6052

S/R Log4(Trigger) Tilt Up

The close switch was not operated the last 
time but three.

OFF

The close switch was operated the last 
time but three.

ON

6053

S/R Log4(Trigger) Multi 
Close

The multi-close function was not operated 
the last time but three.

OFF

The multi-close function was operated the 
last time but three.

ON

6054

S/R Log4(Trigger) Overload Overload was not detected the last time 

but three.

OFF

Overload was detected the last time but 
three.

ON

6055

S/R Log4 IG-SW

The ignition switch was turned OFF the 
last time but three.

OFF

The ignition switch was turned ON the last 
time but three.

ON

6056

S/R Log4 Motor actuate

The motor did not operate the last time but 
three.

OFF

The motor operated the last time but three. ON

6057

S/R Log4 Operation

Sunroof operation permission status was 
"not permitted" the last time but three.

OFF

Sunroof operation permission status was 
"permitted" the last time but three.

ON

Item No. M.U.T.-III display

Check condition

Normal condition

Trouble symptom

Inspection 
procedure 
number

Reference 
page

Sunroof does not work at all.

1

P.42A-146

The sunroof lid glass does not tilt-up (tilt-down, open, and close normally).

2

P.42A-147

The sunroof lid glass does not open (tilt-up, tilt-down, and close normally).

3

P.42A-148

The sunroof lid glass does not tilt-down or close (tilt-up and open normally).

4

P.42A-148

SUNROOF ASSEMBLY

BODY

42A-146

SYMPTOM PROCEDURES

INSPECTION PROCEDURE 1: Sunroof does not work at All.

CAUTION

Before replacing the ECU, ensure that the power 
supply circuit, the earth circuit and the communi-
cation circuit are normal.

COMMENTS ON TROUBLE SYMPTOM

Malfunctions of the sunroof motor assembly power 
supply/earth system, sunroof motor assembly, or 
sunroof switch are suspected.

PROBABLE CAUSES

• Malfunction of the sunroof motor assembly

• Malfunction of the sunroof switch

• Damaged wiring harness and connectors

DIAGNOSTIC PROCEDURE

STEP 1. M.U.T.-III diagnosis code
Check that any sunroof operation-related diagnosis 
codes are set in ETACS-ECU.

Q: Is the diagnosis code set?

YES : 

Refer to diagnosis code chart 

P.42A-139

.

NO : 

Go to Step 2.

STEP 2. Sunroof switch check
Refer to sunroof switch check 

P.42A-154

.

Q: Is the sunroof switch normal?

YES : 

Go to Step 3.

NO : 

Replace the sunroof switch.

STEP 3. Resistance measurement at sunroof 
switch connector (earth line terminal).
(1) Disconnect the connector, and measure the 

resistance at the wiring harness-side connector.

(2) Measure the resistance at the sunroof switch 

connector (earth line terminal) and body earth.

OK: Continuity exists (2 

Ω or less)

Q: Is the check result normal?

YES : 

Go to Step 5.

NO : 

Go to Step 4.

STEP 4. Check of short to earth, and open circuit 
in SW

− line between sunroof motor assembly 

connector and sunroof switch connector.

Q: Is the check result normal?

YES : 

Intermittent malfunction (Refer to GROUP 

00 

− How to Use 

Troubleshooting/Inspection Service Points 

− 

How to Cope with Intermittent Malfunction ).

NO : 

Repair the connector(s) or wiring harness.

STEP 5. Resistance measurement at sunroof 
motor assembly connector (E terminal).
(1) Disconnect the connector, and measure the 

resistance at the wiring harness-side connector.

(2) Measure the resistance at the sunroof motor 

assembly connector (E terminal) and body earth.

OK: Continuity exists (2 

Ω or less)

Q: Is the check result normal?

YES : 

Go to Step 7.

NO : 

Go to Step 6.

STEP 6. Check of short to earth, and open circuit 
in E line between sunroof motor assembly 
connector and body earth.

Q: Is the check result normal?

YES : 

Intermittent malfunction (Refer to GROUP 

00 

− How to Use 

Troubleshooting/Inspection Service Points 

− 

How to Cope with Intermittent Malfunction ).

NO : 

Repair the connector(s) or wiring harness.

STEP 7. Voltage measurement at sunroof motor 
assembly connector (SR+ terminal).
(1) Disconnect the connector, and measure the 

voltage at the wiring harness-side connector.

(2) Measure the voltage at the sunroof motor 

assembly connector (SR+ terminal) and body 

Sunroof anti-trap function (safety mechanism) does not work normally.

5

P.42A-149

Trouble symptom

Inspection 
procedure 
number

Reference 
page

SUNROOF ASSEMBLY

BODY

42A-147

earth.

OK: System voltage

Q: Is the check result normal?

YES : 

Go to Step 9.

NO : 

Go to Step 8.

STEP 8. Check of short to power supply, short to 
earth, and open circuit in SR+ line between 
sunroof motor assembly connector and fusible 
link.

Q: Is the check result normal?

YES : 

Intermittent malfunction (Refer to GROUP 

00 

− How to Use 

Troubleshooting/Inspection Service Points 

− 

How to Cope with Intermittent Malfunction ).

NO : 

Repair the connector(s) or wiring harness.

STEP 9. Voltage measurement at sunroof motor 
assembly connector (IG1 terminal).
(1) Disconnect the connector, and measure the 

voltage at the wiring harness-side connector.

(2) Turn the ignition switch ON position.
(3) Measure the voltage at the sunroof motor 

assembly connector (IG1 terminal) and body 

earth.

OK: System voltage

Q: Is the check result normal?

YES : 

Go to Step 11.

NO : 

Go to Step 10.

STEP 10. Check of short to power supply, short 
to earth, and open circuit in IG1 line between 
sunroof motor assembly connector and fusible 
link.

Q: Is the check result normal?

YES : 

Intermittent malfunction (Refer to GROUP 

00 

− How to Use 

Troubleshooting/Inspection Service Points 

− 

How to Cope with Intermittent Malfunction ).

NO : 

Repair the connector(s) or wiring harness.

STEP 11. Retest the system.
Check that the sunroof works normally.

Q: Is the check result normal?

YES : 

Intermittent malfunction (Refer to GROUP 

00 

− How to Use 

Troubleshooting/Inspection Service Points 

− 

How to Cope with Intermittent Malfunction ).

NO : 

Replace the sunroof motor assembly.

INSPECTION PROCEDURE 2: The Sunroof Lid Glass does not Tilt-up (Tilt-down, Open, and Close 
Normally).

CAUTION

Before replacing the ECU, ensure that the power 
supply circuit, the earth circuit and the communi-
cation circuit are normal.

COMMENTS ON TROUBLE SYMPTOM

Malfunctions of the sunroof motor assembly or sun-
roof switch are suspected.

PROBABLE CAUSES

• Malfunction of the sunroof motor assembly

• Malfunction of the sunroof switch

• Damaged wiring harness and connectors

DIAGNOSTIC PROCEDURE

STEP 1. M.U.T.-III diagnosis code
Check that any sunroof operation-related diagnosis 
codes are set in ETACS-ECU.

Q: Is the diagnosis code set?

YES : 

Refer to diagnosis code chart 

P.42A-139

.

NO : 

Go to Step 2.

STEP 2. Sunroof switch check
Refer to sunroof switch check 

P.42A-154

.

Q: Is the sunroof switch normal?

YES : 

Go to Step 3.

NO : 

Replace the sunroof switch.

STEP 3. Check of open circuit in UP line between 
sunroof motor assembly connector and sunroof 
switch connector.

Q: Is the check result normal?

YES : 

Go to Step 4.

NO : 

Repair the connector(s) or wiring harness.

STEP 4. Retest the system.

Q: Is the roof lid glass tilted-up.

 

 

 

 

 

 

 

Content   ..  529  530  531  532   ..