Mitsubishi Outlander (2013+). Manual - part 530

 

  Index      Mitsubishi     Mitsubishi Outlander - service repair manual 2013 year

 

Search            

 

 

 

 

 

 

 

  

 

Content   ..  528  529  530  531   ..

 

 

Mitsubishi Outlander (2013+). Manual - part 530

 

 

SUNROOF ASSEMBLY

BODY

42A-140

Q: Is the diagnosis code set?

YES : 

Replace the sunroof motor assembly.

NO : 

The diagnosis is complete.

CODE NO. L0632: S/R Switch fall

CAUTION

Before replacing the ECU, ensure that the input 
and output signal circuits are normal.

COMMENTS ON TROUBLE SYMPTOM

Current trouble

• If each switch (up, open, close/down) of the sun-

roof switch has been ON for 60 seconds, 
ETACS-ECU sets the diagnosis code No. L0632.

PROBABLE CAUSES

• Malfunction of the sunroof motor assembly

• Malfunction of the sunroof switch

• Damaged wiring harness and connectors

DIAGNOSTIC PROCEDURE

STEP 1. Check of open circuit in UP, OPEN, CLOS 
line between sunroof motor assembly connector 
and sunroof switch connector.

Q: Is the check result normal?

YES : 

Go to Step 2.

NO : 

Repair the connector(s) or wiring harness.

STEP 2. Diagnosis code recheck
Replace the sunroof switch. Recheck if the diagnosis 
code is set.
(1) Erase the diagnosis code.
(2) Turn the ignition switch from the LOCK (OFF) 

position to the ON position.

(3) Check if the diagnosis code is set.

Q: Is the diagnosis code set?

YES : 

Replace the sunroof motor assembly.

NO : 

The diagnosis is complete.

CODE NO. L0634: S/R Sensor signal

CAUTION

Before replacing the ECU, ensure that the input 
and output signal circuits are normal.

COMMENTS ON TROUBLE SYMPTOM

Current trouble

• If the signal from one of two lid position detection 

sensors cannot be detected, ETACS-ECU sets 
the diagnosis code No. L0634.

PROBABLE CAUSES

• Malfunction of the sunroof motor assembly

DIAGNOSTIC PROCEDURE

Diagnosis code recheck
Recheck if the diagnosis code is set.
(1) Erase the diagnosis code.
(2) Turn the ignition switch from the LOCK (OFF) 

position to the ON position.

(3) Check if the diagnosis code is set.

Q: Is the diagnosis code set?

YES : 

Replace the sunroof motor assembly.

NO : 

The diagnosis is complete.

CODE NO. L0637: S/R Position

CAUTION

Before replacing the ECU, ensure that the input 
and output signal circuits are normal.

COMMENTS ON TROUBLE SYMPTOM

Current trouble

• If the roof lid glass position is out of the specified 

area, ETACS-ECU sets the diagnosis code No. 
L0637.

SUNROOF ASSEMBLY

BODY

42A-141

PROBABLE CAUSES

• Malfunction of the sunroof motor assembly

DIAGNOSTIC PROCEDURE

STEP 1. Check the sunroof fully closed position
(1) Carry out the learning procedures of the sunroof 

fully closed position. Refer to 

P.42A-151

.

(2) Recheck if the diagnosis code is set.

a. Erase the diagnosis code.
b. Turn the ignition switch from the LOCK (OFF) 

position to the ON position.

c. Check if the diagnosis code is set.

Q: Is the check result normal?

YES : 

The diagnosis is complete.

NO : 

Go to Step 2.

STEP 2. Diagnosis code recheck
Recheck if the diagnosis code is set.
(1) Erase the diagnosis code.
(2) Turn the ignition switch from the LOCK (OFF) 

position to the ON position.

(3) Check if the diagnosis code is set.

Q: Is the diagnosis code set?

YES : 

Replace the sunroof motor assembly.

NO : 

The diagnosis is complete.

CODE NO. L0640: S/R Over load

CAUTION

Before replacing the ECU, ensure that the input 
and output signal circuits are normal.

COMMENTS ON TROUBLE SYMPTOM

Current trouble

• If the anti-trap function is activated consecutively 

five times or more, ETACS-ECU sets the diagno-
sis code No. L0640.

PROBABLE CAUSES

• Malfunction of the sunroof motor assembly

DIAGNOSTIC PROCEDURE

STEP 1. Check the sunroof fully closed position
(1) Carry out the learning procedures of the sunroof 

fully closed position. Refer to 

P.42A-151

.

(2) Recheck if the diagnosis code is set.

a. Erase the diagnosis code.
b. Turn the ignition switch from the LOCK (OFF) 

position to the ON position.

c. Check if the diagnosis code is set.

Q: Is the check result normal?

YES : 

The diagnosis is complete.

NO : 

Go to Step 2.

STEP 2. Diagnosis code recheck
Recheck if the diagnosis code is set.
(1) Erase the diagnosis code.
(2) Turn the ignition switch from the LOCK (OFF) 

position to the ON position.

(3) Check if the diagnosis code is set.

Q: Is the diagnosis code set?

YES : 

Replace the sunroof motor assembly.

NO : 

The diagnosis is complete.

DATA LIST REFERENCE TABLE

M1426002100025

LIN (SUN ROOF)

Item No. M.U.T.-III display

Check condition

Normal condition

6001

S/R Part number

−

5850A265

6002

S/R Serial number

−

−

6003

S/R SOFT Ver

−

−

6004

S/R Position

−

−

6005

S/R Position initialize state

Initialisation not completed

Not done

Initialisation completed

OK

6006

S/R Overload(Motor lock)

Overload due to a motor lock not detected OFF

Overload due to a motor lock detected

ON

SUNROOF ASSEMBLY

BODY

42A-142

6007

S/R Overload(Pulse 
change)

Overload due to a pulse modulation not 
detected

OFF

Overload due to a pulse modulation 
detected

ON

6010

S/R Power supply voltage

Always

System voltage

6011

S/R Open switch

The open switch is not being operated

Not actuated

The open switch is being operated

Actuated

6012

S/R Close switch

The close switch is not being operated

Not actuated

The close switch is being operated

Actuated

6013

S/R Tilt up switch

The tilt-up switch is not being operated

Not actuated

The tilt-up switch is being operated

Actuated

6014

S/R Ignition switch

When the ignition switch is turned to the 
LOCK or ACC position.

OFF

When the ignition switch is turned to the 
ON or START position.

ON

6015

S/R Ignition switch(LIN)

When the ignition switch is turned to the 
LOCK or ACC position.

OFF

When the ignition switch is turned to the 
ON or START position.

ON

6018

S/R Operation

Communication is not normal

Disable

Communication is normal

Enable

6019

S/R Multi close

The multi-close function not in progress

OFF

The multi-close function in progress

ON

6020

S/R Operation mode

−

Type 2

6021

S/R Vehicle speed

Perform a test run of the vehicle.

The values displayed 
on the speedometer 
and M.U.T.-III are 
almost the same.

6022

S/R Position state

The sunroof position not confirmed

Undecided pos.

The sunroof is at tilt-up position.

Tilt up

The sunroof is slid to open.

Slide open

The sunroof is fully closed.

Full close

6023

S/R Sleep condition

Communication sleep conditions not 
satisfied

OFF

Communication sleep conditions satisfied

ON

6024

S/R Motor

The motor not running

Not actuated

The motor running

Actuated

6026

S/R Log1(Trigger) Open

The open switch was not operated the last 
time.

OFF

The open switch was operated the last 
time.

ON

Item No. M.U.T.-III display

Check condition

Normal condition

SUNROOF ASSEMBLY

BODY

42A-143

6027

S/R Log1(Trigger) Close

The close switch was not operated the last 
time.

OFF

The close switch was operated the last 
time.

ON

6028

S/R Log1(Trigger) Tilt Up

The close switch was not operated the last 
time.

OFF

The close switch was operated the last 
time.

ON

6029

S/R Log1(Trigger) Multi 
Close

The multi-close function was not operated 
the last time.

OFF

The multi-close function was operated the 
last time.

ON

6030

S/R Log1(Trigger) Overload Overload was not detected the last time.

OFF

Overload was detected the last time.

ON

6031

S/R Log1 IG-SW

The ignition switch was turned OFF the 
last time.

OFF

The ignition switch was turned ON the last 
time.

ON

6032

S/R Log1 Motor actuate

The motor did not operate the last time.

OFF

The motor operated the last time.

ON

6033

S/R Log1 Operation

Sunroof operation permission status was 
"not permitted" the last time.

OFF

Sunroof operation permission status was 
"permitted" the last time.

ON

6034

S/R Log2(Trigger) Open

The open switch was not operated the last 
time but one.

OFF

The open switch was operated the last 
time but one.

ON

6035

S/R Log2(Trigger) Close

The close switch was not operated the last 
time but one.

OFF

The close switch was operated the last 
time but one.

ON

6036

S/R Log2(Trigger) Tilt Up

The close switch was not operated the last 
time but one.

OFF

The close switch was operated the last 
time but one.

ON

6037

S/R Log2(Trigger) Multi 
Close

The multi-close function was not operated 
the last time but one.

OFF

The multi-close function was operated the 
last time but one.

ON

6038

S/R Log2(Trigger) Overload Overload was not detected the last time 

but one.

OFF

Overload was detected the last time but 
one.

ON

Item No. M.U.T.-III display

Check condition

Normal condition

 

 

 

 

 

 

 

Content   ..  528  529  530  531   ..