Jeep Wrangler TJ. Manual - part 274

 

  Index      Jeep     Jeep Wrangler TJ - service repair manual 2005 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  272  273  274  275   ..

 

 

Jeep Wrangler TJ. Manual - part 274

 

 

• Sentry Key Immobilizer System “Customer

Learn” Mode Announcement - This chime feature
is only active on vehicles equipped with the optional
Sentry Key Immobilizer System (SKIS) and sold in
markets where the optional “Customer Learn” pro-
gramming feature is available. The instrument clus-
ter chime tone generator will generate one chime to
announce that a status message input received from
the Sentry Key Immobilizer Module (SKIM) over the
PCI data bus indicates that the SKIS is in the “Cus-
tomer Learn” mode, which is used for programming
additional sentry key transponders.

• Turn Signal On Warning - The instrument

cluster chime tone generator will generate repetitive
chimes at a slow rate to announce that the hard
wired input for the right or left turn signal indicator
as well as vehicle distance and speed message inputs
received from the PCM over the PCI data bus indi-
cate that a turn signal has been active continuously
for 1.6 kilometers (1 mile) with the vehicle speed
greater than 22 kilometers-per-hour (15 miles-per
hour). Vehicles built for markets other than the
United States and Canada have a revised distance
threshold of 4 kilometers for this feature. The chime
will continue until the turn signal input becomes
inactive, the status changes, or until the vehicle
speed message indicates that the speed is less than
22 kilometers-per-hour (15 miles-per-hour), which-
ever occurs first. The hazard warning flashers will
not activate this chime feature.

The instrument cluster provides chime service for

all available features in the chime warning system.
The instrument cluster relies upon its internal pro-
gramming,

hard

wired

inputs

from

numerous

switches, and electronic message inputs received
from other electronic modules over the PCI data bus
network. Upon receiving the proper inputs, the
instrument cluster activates the integral chime tone
generator to provide the audible chime to the vehicle
operator. The chime tone generator in the instrument
cluster is capable of producing single chime tones, or
repeated chime tones at two different rates: about
fifty chime tones per minute, or about 180 chime
tones per minute. The internal programming of the
instrument cluster determines the priority of each
chime request input that is received, as well as the

rate and duration of each chime that is to be gener-
ated.

The hard wired chime warning system inputs to

the instrument cluster, as well as other hard wired
circuits for this system may be diagnosed and tested
using conventional diagnostic tools and procedures.
However, conventional diagnostic methods may not
prove conclusive in the diagnosis of the instrument
cluster or the PCI data bus network. The most reli-
able, efficient and accurate means to diagnose the
instrument cluster and the PCI data bus network
inputs for the chime warning system requires the use
of a DRBIII

t scan tool. Refer to the appropriate diag-

nostic information.

DIAGNOSIS AND TESTING - CHIME WARNING
SYSTEM

The chime warning system features driven by hard

wired inputs to the instrument cluster may be diag-
nosed and tested using conventional diagnostic tools
and procedures. However, conventional diagnostic
methods may not prove conclusive in the diagnosis of
the chime warning system features driven by mes-
sage inputs to the instrument cluster over the Pro-
grammable Communications Interface (PCI) data bus
network. The most reliable, efficient and accurate
means to diagnose the instrument cluster and the
PCI data bus network inputs for the chime warning
system requires the use of a DRBIII

t scan tool. Refer

to the appropriate diagnostic and wiring information.

WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS, DISABLE THE AIRBAG SYSTEM BEFORE
ATTEMPTING ANY STEERING WHEEL, STEERING
COLUMN, OR INSTRUMENT PANEL COMPONENT
DIAGNOSIS OR SERVICE. DISCONNECT AND ISO-
LATE THE BATTERY NEGATIVE (GROUND) CABLE,
THEN WAIT TWO MINUTES FOR THE AIRBAG SYS-
TEM CAPACITOR TO DISCHARGE BEFORE PER-
FORMING FURTHER DIAGNOSIS OR SERVICE. THIS
IS THE ONLY SURE WAY TO DISABLE THE AIRBAG
SYSTEM. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN ACCIDENTAL AIR-
BAG DEPLOYMENT AND POSSIBLE PERSONAL
INJURY.

TJ

CHIME/BUZZER

8B - 3

CHIME WARNING SYSTEM (Continued)

CONDITION

POSSIBLE CAUSES

CORRECTION

NO SEAT BELT WARNING

CHIME WITH SEAT BELT

UNBUCKLED, BUT OTHER

CHIME FEATURES OK

1. Seat belt switch ground
circuit open.

1. Check for continuity between the ground circuit
of the floor wire harness connector for the seat
belt switch and a good ground. Repair open
ground circuit, if required.

2. Seat belt switch sense
circuit open.

2. Check for continuity between the seat belt
switch sense circuit of the floor wire harness
connector for the seat belt switch and the
instrument panel wire harness instrument cluster
connector. Repair the open seat belt switch sense
circuit, if required.

3. Faulty seat belt switch.

3. Check for continuity between the ground circuit
and the seat belt switch sense circuit of the seat
belt switch pigtail connector. There should be
continuity with the seat belt unbuckled. Replace
the faulty seat belt, if required.

SEAT BELT WARNING

CHIME WITH SEAT BELT

BUCKLED

1. Seat belt switch sense
circuit shorted.

1. With the floor wire harness connector for the
seat belt switch and the instrument panel wire
harness instrument cluster connector
disconnected, there should be no continuity
between the seat belt switch sense circuit and a
good ground. Repair the shorted seat belt switch
sense circuit, if required.

2. Faulty seat belt switch.

2. Check for continuity between the ground circuit
cavity and the seat belt switch sense circuit of the
seat belt switch pigtail connector. There should
be no continuity with the seat belt buckled.
Replace the faulty seat belt, if required.

NO KEY-IN IGNITION

WARNING CHIME, BUT

OTHER CHIME FEATURES

OK

1. Driver door ajar switch
sense circuit open.

1. Check for continuity between the driver door
ajar switch sense circuit of the connector for the
driver door ajar switch and the cross body wire
harness ignition switch connector. Repair the
open driver door ajar switch sense circuit, if
required.

2. Key-in ignition switch
sense circuit open.

2. Check for continuity between the key-in ignition
switch sense circuit of the cross body wire
harness ignition switch connector and the
instrument panel wire harness instrument cluster
connector. Repair the open key-in ignition switch
sense circuit, if required.

3. Ignition switch ground
circuit open.

3. Check for continuity between the ground circuit
cavity of the cross body wire harness ignition
switch connector and a good ground. Repair the
open ground circuit, if required

4. Faulty ignition switch.

4. Check for continuity between the ground circuit
terminal and the key-in ignition switch sense
circuit terminal in the ignition switch connector.
There should be continuity with a key in the
ignition lock cylinder. Replace the faulty ignition
switch, if required.

8B - 4

CHIME/BUZZER

TJ

CHIME WARNING SYSTEM (Continued)

CONDITION

POSSIBLE CAUSES

CORRECTION

NO HEADLAMPS-ON

WARNING CHIME, BUT

OTHER CHIME FEATURES

OK

1. Driver door ajar switch
sense circuit open.

1. Check for continuity between the driver door
ajar switch sense circuit of the connector for the
driver door ajar switch and the instrument panel
wire harness instrument cluster connector. Repair
the open driver door ajar switch sense circuit, if
required.

2. Headlamp switch output
circuit open.

2. Check for continuity between the headlamp
switch output circuit of the instrument panel wire
harness instrument cluster connector and the
park lamp feed circuit of the cross body wire
harness left multi-function switch connector.
Repair the open headlamp switch output circuit, if
required.

3. Faulty multi-function
switch.

3. Check for continuity between the B(+) circuit
terminal and the park lamp feed circuit terminal in
the left multi-function switch connector. There
should be continuity with the headlamp switch in
the On position. Replace the faulty left multi-
function switch, if required.

NO CHIMES AND OTHER

INSTRUMENT CLUSTER

FEATURES ERRATIC OR

DISABLED

1. Instrument cluster ground
circuit open.

1. Check for continuity between the ground circuit
of the instrument panel wire harness instrument
cluster connector and a good ground. Repair the
open ground circuit, if required.

2. Instrument cluster fused
B(+) circuit open.

2. Check for battery voltage at the B(+) circuit of
the instrument panel wire harness instrument
cluster connector. Repair the open fused B(+)
circuit, if required.

3. Instrument cluster fused
ignition switch output
(run-start) circuit open.

3. With the ignition switch in the On position,
check for battery voltage at the fused ignition
switch output (run-start) circuit of the instrument
panel wire harness instrument cluster connector.
Repair the open fused ignition switch output
(run-start) circuit, if required.

4. Faulty instrument cluster.

4. Replace the faulty instrument cluster, if
required.

NO CHIMES, BUT ALL
OTHER INSTRUMENT

CLUSTER FEATURES OK

1. Faulty instrument cluster.

1. Replace the faulty instrument cluster, if
required.

TJ

CHIME/BUZZER

8B - 5

CHIME WARNING SYSTEM (Continued)

 

 

 

 

 

 

 

Content   ..  272  273  274  275   ..