Jeep Grand Cherokee WK. Manual - part 1710

 

  Index      Jeep     Jeep Grand Cherokee WK - service repair manual 2005 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1708  1709  1710  1711   ..

 

 

Jeep Grand Cherokee WK. Manual - part 1710

 

 

77–EBL OUTPUT SHORTED HIGH

24 - 188

HVAC - ELECTRICAL DIAGNOSTICS

WK

77–EBL OUTPUT SHORTED HIGH (CONTINUED)

For the Manual Temperature Control (MTC) circuit diagram (Refer to 24 - HEATING & AIR CONDITIONING - SCHE-
MATICS AND DIAGRAMS).

For a complete wiring diagram Refer to Section 8W.

When Monitored:
With the Ignition on and the EBL mode switch on.

Set Condition:
If the A/C Heater Control senses excessive current on the (C115) Defogger Relay Control circuit.

Possible Causes

EBL RELAY SHORTED TO BATTERY

(C115) DEFOGGER RELAY CONTROL CIRCUIT SHORTED TO BATTERY

JUNCTION BLOCK

A/C HEATER CONTROL

NOTE: This DTC must be active for the results of this test to be valid. Do not perform this test if this DTC
is stored. Refer to HVAC System Test (MTC) for stored DTC test procedures.

Diagnostic Test

1.

CHECK THE EBL RELAY FOR A SHORT TO BATTERY

Turn the ignition off.

Install a known good relay in place of the EBL relay.

Turn the ignition on.

Actuate the Clear DTC function by performing the following:

Turn the blower control on.

Press the A/C mode switch down, turn the blower control to off,
wait 5 seconds and then release the A/C mode switch.

When the A/C status indicator begins displaying DTCs, set the
Mode switch to the floor position, simultaneously press the A/C
mode switch and the EBL mode switch down for 5 seconds and
then release the mode switches. Stored DTCs will clear from
memory in approximately two seconds.

Press the EBL mode switch on.

Actuate the Display DTC function by performing the following:

Turn the blower control on.

Press the A/C mode switch down, turn the blower control to off,
wait 5 seconds and then release the A/C mode switch.

NOTE: The A/C status indicator displays active DTCs when the EBL status indictor is not illuminated and
stored DTCs when the EBL status indicator is illuminated.
Read DTCs from the A/C status indictor.

Does the A/C status indicator display DTC 77?

Yes

>> Go To 2

No

>> Replace the original EBL Relay in accordance with the Service Information.

Perform BODY VERIFICATION TEST - VER 1. (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL
MODULES - STANDARD PROCEDURE).

WK

HVAC - ELECTRICAL DIAGNOSTICS

24 - 189

77–EBL OUTPUT SHORTED HIGH (CONTINUED)

2.

CHECK FOR A SHORTED A/C HEATER CONTROL

Turn the ignition off.

Remove the replacement EBL relay.

Disconnect the A/C Heater Control C1 harness connector.

Turn the ignition on.

Measure the voltage of the (C115) Defogger Relay Control circuit.

Is the voltage above 0.2 volts?

Yes

>> Go To 3

No

>> Replace the A/C Heater Control in accordance with the

Service Information.

Perform BODY VERIFICATION TEST - VER 1. (Refer to 8
- ELECTRICAL/ELECTRONIC CONTROL MODULES -
STANDARD PROCEDURE).

3.

CHECK THE (C115) DEFOGGER RELAY CONTROL CIRCUIT FOR A SHORT TO BATTERY

Turn the ignition off.

Disconnect the Junction Block C2 harness connector.

Turn the ignition on.

Measure the voltage of the (C115) Defogger Relay Control circuit.

Is the voltage above 0.2 volts?

Yes

>> Repair the (C115) Defogger Relay Control circuit for a

short to battery.

Perform BODY VERIFICATION TEST - VER 1. (Refer to 8
- ELECTRICAL/ELECTRONIC CONTROL MODULES -
STANDARD PROCEDURE).

No

>> Replace the Junction Block in accordance with the Service

Information.

Perform BODY VERIFICATION TEST - VER 1. (Refer to 8
- ELECTRICAL/ELECTRONIC CONTROL MODULES -
STANDARD PROCEDURE).

24 - 190

HVAC - ELECTRICAL DIAGNOSTICS

WK

81–BLOWER NOT ON HIGH AT START OF COOLDOWN TEST (MTC)

WK

HVAC - ELECTRICAL DIAGNOSTICS

24 - 191

 

 

 

 

 

 

 

Content   ..  1708  1709  1710  1711   ..