Infiniti G35 (V35) Sedan. Manual - part 1395

TM-272

< ON-VEHICLE REPAIR >

[5AT: RE5R05A]

A/T FLUID COOLER TUBE

5.

Remove the A/T fluid cooler tube from the A/T assembly and engine assembly.

6.

Remove the stabilizer bar. Refer to 

FSU-19, "Exploded View"

.

7.

Loosen the lower mounting nuts for the engine mounting insulators (RH and LH). Refer to 

EM-77, "2WD :

Exploded View"

.

8.

Set an engine stand to the engine assembly and slightly lift the engine assembly.

CAUTION:

Do not pull the harnesses, hoses, etc. excessively.

9.

Remove the A/T fluid cooler tube from the vehicle.

CAUTION:

Be careful not to bend A/T fluid cooler tube.

INSTALLATION

Install in the reverse order of removal.

2WD : Inspection

INFOID:0000000000957176

INSPECTION AFTER INSTALLATION

After completing installation, check for A/T fluid leakage and A/T fluid level. Refer to 

TM-217, "Inspection"

.

AWD

AWD : Exploded View

INFOID:0000000000957177

A/T FLUID COOLER TUBE

TM-273

< ON-VEHICLE REPAIR >

[5AT: RE5R05A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

AWD : Removal and Installation

INFOID:0000000000957178

REMOVAL

1.

Remove the front and rear engine undercover with power tool.

2.

Remove the front suspension member. Refer to 

FSU-19, "Exploded View"

.

3.

Remove exhaust front tube and center muffler with power tool. Refer to 

EX-5, "Exploded View"

.

4.

Remove exhaust mounting bracket. Refer to 

EX-5, "Exploded View"

.

5.

Remove the three way catalyst (right bank). Refer to 

EX-5, "Exploded View"

6.

Remove front propeller shaft. Refer to 

DLN-80, "Exploded View"

.

7.

Pull out the A/T fluid cooler hose from the A/T fluid cooler tube. Refer to 

CO-14, "Exploded View"

.

8.

Remove the A/T fluid cooler tube from the A/T assembly and engine assembly.

CAUTION:

1.

Engine assembly

2.

A/T assembly

3.

Copper washer

4.

A/T fluid cooler tube

5.

Bracket

6.

Bracket

Refer to 

GI-4, "Components"

 for symbols in the figure.

JPDIA0054GB

TM-274

< ON-VEHICLE REPAIR >

[5AT: RE5R05A]

A/T FLUID COOLER TUBE

Be careful not to bend A/T fluid cooler tube.

INSTALLATION

Install in the reverse order of removal.

AWD : Inspection

INFOID:0000000000957179

INSPECTION AFTER INSTALLATION

After completing installation, check for A/T fluid leakage and A/T fluid level. Refer to 

TM-217, "Inspection"

.

TRANSMISSION ASSEMBLY

TM-275

< REMOVAL AND INSTALLATION >

[5AT: RE5R05A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

REMOVAL AND INSTALLATION

TRANSMISSION ASSEMBLY

2WD

2WD : Exploded View

INFOID:0000000000957180

2WD : Removal and Installation

INFOID:0000000000957181

REMOVAL

CAUTION:

• When removing the A/T assembly from engine, first remove the crankshaft position sensor (POS)

from the A/T assembly.

• Be careful not to damage sensor edge.

1.

Disconnect the battery cable from the negative terminal.

2.

Remove A/T fluid level gauge.

3.

Remove air cleaner case (RH). Refer to 

EM-25, "Exploded View"

.

4.

Remove engine under cover with power tool.

5.

Remove exhaust front tube and center muffler with power tool. Refer to 

EX-5, "Exploded View"

.

1.

A/T fluid level gauge

2.

A/T fluid charging pipe

3.

O-ring

4.

Copper washer

5.

A/T fluid cooler tube

6.

Bracket

7.

Bracket

8.

A/T assembly

A.

For tightening torque, refer to 

TM-

275, "2WD : Removal and Installa-
tion"

.

Refer to 

GI-4, "Components"

 for symbols in the figure.

JPDIA0047GB