Infiniti G35 (V35) Sedan. Manual - part 1390

TM-252

< ON-VEHICLE REPAIR >

[5AT: RE5R05A]

A/T FLUID TEMPERATURE SENSOR 2

7.

Install oil pan (2) (with oil pan gasket) and clips (1) to transmis-
sion case.

CAUTION:

• Install it so that drain plug (3) comes to the position as

shown in the figure.

• Be careful not to pinch harnesses.
• Completely remove all moisture, oil and old gasket, etc.

from oil pan mounting surface.

8.

Tighten oil pan mounting bolts to the specified torque in numeri-
cal order shown in the figure after temporarily tightening them.
Tighten oil pan mounting bolts to the specified torque.

CAUTION:

Do not reuse oil pan mounting bolts.

9.

Install drain plug to oil pan. Tighten drain plug to the specified
torque.

CAUTION:

Do not reuse drain plug gasket.

10. Install bracket (2) to transmission assembly.

11. Install heated oxygen sensor 2 harness (B) to clips (1).

12. Connect heated oxygen sensor 2 harness connector (A).
13. Install exhaust mounting bracket. Refer to 

EX-5, "Exploded

View"

.

14. Pour ATF into A/T assembly. Refer to 

TM-218, "Changing"

.

15. Connect the battery cable to the negative terminal.

Inspection

INFOID:0000000000957157

INSPECTION AFTER REMOVAL

Check foreign materials in oil pan to help determine causes of mal-
function. If the ATF is very dark, smells burned, or contains foreign
particles, the frictional material (clutches, band) may need replace-
ment. A tacky film that will not wipe clean indicates varnish build up.
Varnish can cause valves, servo, and clutches to stick and can
inhibit pump pressure.
• If frictional material is detected, perform A/T fluid cooler

cleaning. Refer to 

TM-220, "Cleaning"

.

INSPECTION AFTER INSTALLATION

After completing installation, check for A/T fluid leakage and A/T fluid level. Refer to 

TM-217, "Inspection"

.

: Vehicle front

: Oil pan mounting bolt

SCIA8117E

: Vehicle front

: Vehicle front

: Bolt

JPDIA0021ZZ

SCIA8269E

SCIA5199E

PARKING COMPONENTS

TM-253

< ON-VEHICLE REPAIR >

[5AT: RE5R05A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

PARKING COMPONENTS

2WD

2WD : Exploded View

INFOID:0000000000957158

2WD : Removal and Installation

INFOID:0000000000957159

REMOVAL

1.

Drain ATF through drain plug.

2.

Remove exhaust front tube and center muffler with power tool. Refer to 

EX-5, "Exploded View"

.

3.

Remove rear propeller shaft. Refer to 

DLN-93, "Exploded View"

.

4.

Remove control rod. Refer to 

TM-236, "2WD : Exploded View"

.

5.

Support A/T assembly with a transmission jack.

CAUTION:

When setting transmission jack, be careful not to allow it to collide against the drain plug.

6.

Remove rear engine mounting member with power tool. Refer to 

EM-77, "2WD : Exploded View"

.

7.

Remove engine mounting insulator (rear). Refer to 

EM-77, "2WD : Exploded View"

.

1.

Rear oil seal

2.

Rear extension

3.

Parking actuator support

4.

Return spring

5.

Parking pawl

6.

Pawl shaft

7.

Self-sealing bolt

8.

Seal ring

9.

Parking gear

10.

Output shaft

11.

Bearing race

12. Needle bearing

*

: Apply Genuine Anaerobic Liquid Gasket or equivalent. Refer to 

GI-15, "Recommended Chemical Products and Sealants"

.

Refer to 

GI-4, "Components"

 for symbols not described on the above.

SCIA8364E

TM-254

< ON-VEHICLE REPAIR >

[5AT: RE5R05A]

PARKING COMPONENTS

8.

Remove tightening bolts for rear extension assembly and trans-
mission case.

9.

Tap rear extension assembly with a soft hammer (A).

10. Remove rear extension assembly (with needle bearing) from

transmission case.

11. Remove bearing race (1) from output shaft (2).

12. Remove output shaft (1) from transmission case by rotating left/

right.

1

: Self-sealing bolt

A

:  Bolt

JPDIA0026ZZ

JPDIA0027ZZ

SCIA3431E

JPDIA0057ZZ

JPDIA0028ZZ

PARKING COMPONENTS

TM-255

< ON-VEHICLE REPAIR >

[5AT: RE5R05A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

13. Remove parking gear (1) from output shaft (2).

14. Remove seal rings (1) from output shaft.

15. Remove needle bearing (1) from rear extension.

16. Remove parking actuator support (1) from rear extension.

17. Remove parking pawl (with return spring) (1) and pawl shaft (2)

from rear extension.

JPDIA0029ZZ

JPDIA0030ZZ

SCIA6179J

JPDIA0031ZZ

JPDIA0032ZZ