Infiniti G35 (V35) Sedan. Manual - part 1391

TM-256

< ON-VEHICLE REPAIR >

[5AT: RE5R05A]

PARKING COMPONENTS

18. Remove return spring (1) from parking pawl (2).

19. Remove rear oil seal (1) from rear extension using flat-blade

screwdriver (A).

CAUTION:

Be careful not to scratch rear extension.

INSTALLATION

1.

As shown in the figure, use a drift [SST: ST33400001 (J-26082)]
(A) to drive rear oil seal into the rear extension until it is flush.

CAUTION:

• Do not reuse rear oil seal.
• Apply ATF to rear oil seal.

2.

Install return spring (1) to parking pawl (2).

SCIA6180J

JPDIA0033ZZ

JPDIA0035ZZ

SCIA6180J

PARKING COMPONENTS

TM-257

< ON-VEHICLE REPAIR >

[5AT: RE5R05A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

3.

Install parking pawl (with return spring) (1) and pawl shaft (2) to
rear extension.

4.

Install parking actuator support (1) to rear extension.

5.

Install bearing (1) to rear extension.

CAUTION:

Take care with the direction of needle bearing. Refer to 

TM-

289, "Location of Adjusting Shims, Needle Bearings, Thrust
Washers and Snap Rings"

.

6.

Install seal rings (1) to output shaft.

7.

Install parking gear (1) to output shaft (2).

JPDIA0032ZZ

JPDIA0031ZZ

SCIA6179J

JPDIA0030ZZ

JPDIA0029ZZ

TM-258

< ON-VEHICLE REPAIR >

[5AT: RE5R05A]

PARKING COMPONENTS

8.

Install output shaft (1) in transmission case.

9.

Install bearing race (1) to output shaft (2).

10. Apply recommended sealant (Genuine Anaerobic Liquid Gasket

or equivalent. Refer to 

GI-15, "Recommended Chemical Prod-

ucts and Sealants"

.) to rear extension assembly as shown in the

figure.

CAUTION:

Completely remove all moisture, oil and old sealant, etc.
from the transmission case and rear extension assembly
mounting surfaces.

11. Install rear extension assembly (with needle bearing) to trans-

mission case.

CAUTION:

Insert the tip of parking rod between the parking pawl and
the parking actuator support when assembling the rear
extension assembly. 

JPDIA0028ZZ

JPDIA0057ZZ

A

: Start and finish point shall be in 
the center of two bolts.

B

: 3 – 5 mm (0.12 – 0.20 in)

Sealant 
width (C)

: 1.0 – 2.0 mm (0.04 – 0.08 in)

Sealant 
height (C)

: 0.4 – 1.0 mm (0.016 – 0.04 in)

JPDIA0036ZZ

SCIA3431E

PARKING COMPONENTS

TM-259

< ON-VEHICLE REPAIR >

[5AT: RE5R05A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

12. Tighten rear extension assembly bolts to the specified torque.

13. Install engine mounting insulator (rear). Refer to 

EM-77, "2WD :

Exploded View"

.

14. Install rear engine mounting member. Refer to 

EM-77, "2WD :

Exploded View"

.

15. Install control rod. Refer to 

TM-236, "2WD : Exploded View"

.

16. Install rear propeller shaft. Refer to 

DLN-93, "Exploded View"

.

17. Install exhaust front tube and center muffler. Refer to 

EX-5, "Exploded View"

.

18. Install drain plug to oil pan. Tighten a necessary drain plug with specified torque. Refer to 

TM-240,

"Exploded View"

.

CAUTION:

Do not reuse drain plug gasket.

19. Pour ATF into A/T assembly. Refer to 

TM-218, "Changing"

.

2WD : Inspection

INFOID:0000000000957160

INSPECTION AFTER REMOVAL

If the contact surface on parking actuator support (1), parking pawl
(2) and etc. has excessive wear, abrasion, bend, or any other dam-
age, replace the components.

INSPECTION AFTER INSTALLATION

After completing installation, check the following item.
• A/T fluid leakage and A/T fluid level. Refer to 

TM-217, "Inspection"

.

• A/T position. Refer to

TM-230, "2WD : Inspection and Adjustment"

.

1

: Self-sealing bolt

A

:  Bolt

JPDIA0026ZZ

JPDIA0034ZZ