Chrysler Town, Dodge Caravan. Manual - part 458

 

  Index      Chrysler     Chrysler TOWN & COUNTRY, VOYAGER, Dodge Caravan - service repair manual 2001-2007 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  456  457  458  459   ..

 

 

Chrysler Town, Dodge Caravan. Manual - part 458

 

 

QUAD BUCKET SEAT SIDE
SHIELD - NO CUP HOLDER

REMOVAL

(1) Remove the three screws (Fig. 28).
(2) Remove the side shield.

INSTALLATION

(1) Install the side shield hook into the rectangu-

lar hole on the riser.

(2) Install the three screws.

QUAD BUCKET SEAT RISER

REMOVAL

(1) Remove the seat from vehicle. Refer to Owner’s

Manual for proper procedures.

(2) Remove seat side shield/cupholder. (Refer to 23

-

BODY/SEATS/QUAD

BUCKET

SEAT

SIDE

SHIELD/CUP HOLDER - REMOVAL)

(3) Remove the seat side shield. (Refer to 23 -

BODY/SEATS/QUAD BUCKET SEAT SIDE SHIELD
- NO CUP HOLDER - REMOVAL)

(4) Remove the five bolts, two nuts, strut bushing

and remove the riser from the seat (Fig. 29).

INSTALLATION

(1) Install the riser, the strut bushing into the

hole, the five bolts, two nuts and tighten all fasteners
to 40 N·m (30 ft. lbs.).

(2) Install the seat side shield. (Refer to 23 -

BODY/SEATS/QUAD BUCKET SEAT SIDE SHIELD
- NO CUP HOLDER - INSTALLATION)

Fig. 26 SIDE SHIELD/CUP HOLDER ATTACHMENT

CLIPS

1 - SIDE SHIELD/CUP HOLDER
2 - LOCK TAB
3 - SEAT RISER

Fig. 27 SIDE SHIELD/CUP HOLDER ATTACHMENT

PIN

1 - SEAT RISER
2 - ATTACHMENT PIN
3 - SIDE SHIELD/CUP HOLDER

Fig. 28 SEAT SIDE COVER - QUAD BUCKETS

1 - SIDE SHIELD SCREWS
2 - SIDE SHIELD

23 - 96

SEATS

RS

QUAD BUCKET SEAT SIDE SHIELD/CUP HOLDER (Continued)

(3) Install the seat side shield/cup holder. (Refer to

23 - BODY/SEATS/QUAD BUCKET SEAT SIDE
SHIELD/CUP HOLDER - INSTALLATION)

(4) Install the seat. Refer to Owner’s Manual for

proper procedures.

BUCKET SEAT BACK - QUAD
BUCKET

REMOVAL

NOTE: Quad seats equipped with child restraint
seats have an interlock feature that will not allow the
seat back to fold forward with the child seat open.

(1) Remove the headrests. (Refer to 23 - BODY/

SEATS/HEADREST - REMOVAL)

(2) Remove the armrests, if equipped. (Refer to 23

- BODY/SEATS/ARMREST - REMOVAL)

(3) Remove the seatback hinge covers. (Refer to 23

- BODY/SEATS/SEAT BACK HINGE COVERS -
QUAD BUCKET, 50/50 SPLIT, BENCH - REMOVAL)

(4) Disconnect the child seat synchronizer cable, if

equipped. (Fig. 30)

(5) Remove the seatback frame bolts and remove

the seat back. (Fig. 31)

INSTALLATION

(1) Install the seatback.
(2) Install the shoulder bolts attaching the seat-

back hinge to the seat back frame and tighten to 34
N·m (25 ft. lbs.) torque.

(3) Connect the child seat synchronizer cable, if

equipped.

(4) Install the seatback hinge covers. (Refer to 23 -

BODY/SEATS/SEAT

BACK

HINGE

COVERS

-

QUAD BUCKET, 50/50 SPLIT, BENCH - INSTALLA-
TION)

(5) Install the armrests. (Refer to 23 - BODY/

SEATS/ARMREST - INSTALLATION)

(6) Install the headreast. (Refer to 23 - BODY/

SEATS/HEADREST - INSTALLATION)

(7) Verify seatback operation.

Fig. 29 BUCKET SEAT RISER - QUAD BUCKET

1 - SEAT SIDE SHIELD/CUP HOLDER
2 - SEAT RISER
3 - SEAT SIDE SHIELD
4 - RISER BOLTS

Fig. 30 QUAD SEAT SYNCHRONIZER CABLE

1 - CABLE END CONNECTOR
2 - SYNCHRONIZER CABLE
3 - SEATBACK HINGE

Fig. 31 SEAT BACK HINGE - TYPICAL

1 - SEATBACK FRAME SHOULDER BOLTS
2 - SEAT CUSHION FRAME BOLTS
3 - SEATBACK HINGE

RS

SEATS

23 - 97

QUAD BUCKET SEAT RISER (Continued)

BENCH SEATBACK PANEL

REMOVAL

(1) On third row seats remove plastic grocery bag

retainer. (Refer to 23 - BODY/SEATS/PLASTIC GRO-
CERY BAG RETAINER - REMOVAL)

(2) Using a fork type prying tool (C4829) on three

pass seats, disengage push-in fasteners holding seat
back cover to seat back frame and remove seat back
cover from seat. (Fig. 32).

(3) Using a fork type prying tool (C4829) on two

pass seats, disengage push-in fasteners holding the
upper corners and lower edge of the seat back panel
to seat back frame and remove seat back cover from
seat by pulling the lower edge out away from the
seatback to disengage the upper two hooks. (Fig. 33).

INSTALLATION

(1) On three pass seats place seat back panel in

position on seat and install the push-in fasteners
(Fig. 32).

(2) On two pass seats engage the two upper hooks

of the panel, place the panel into position and install
the push-in fasteners (Fig. 33).

(3) On third row bench seats install grocery bag

holder. (Refer to 23 - BODY/SEATS/PLASTIC GRO-
CERY BAG RETAINER - INSTALLATION)

SEAT CUSHION COVER -
QUAD BUCKET, 50/50 SPLIT,
BENCH

REMOVAL

BENCH SEAT & 50/50 SPLIT

(1) Remove seat from vehicle. Refer to Owner’s

Manual for proper procedures.

(2) Remove seat back. (Refer to 23 - BODY/SEATS/

BENCH SEAT BACK - REMOVAL)

(3) Remove seat risers. (Refer to 23 - BODY/

SEATS/BENCH

SEAT

RISER

-

50/50

SPLIT

-

REMOVAL) and (Refer to 23 - BODY/SEATS/BENCH
SEAT RISER - FIRST ROW - REMOVAL) and (Refer
to 23 - BODY/SEATS/BENCH SEAT RISER - SEC-
OND ROW - REMOVAL)

(4) Disconnect the cushion cover J-straps.
(5) Remove seat cushion cover from seat cushion.

QUAD BUCKET

(1) Remove seat from vehicle. Refer to Owner’s

Manual for proper procedures.

(2) Remove seat back.(Refer to 23 - BODY/SEATS/

BUCKET

SEAT

BACK

-

QUAD

BUCKET

-

REMOVAL)

(3) Remove seat risers. (Refer to 23 - BODY/

SEATS/QUAD BUCKET SEAT RISER - REMOVAL)

(4) Disconnect the cushion cover J-straps.
(5) Remove seat cushion cover from seat cushion.

Fig. 32 THREE - PASS BENCH SEATBACK PANEL

1 - SEATBACK REAR PANEL
2 - FIRST REAR CHILD RESTRAINT SEAT

Fig. 33 TWO - PASSENGER BENCH SEATBACK

PANEL

1 - SEATBACK REAR PANEL
2 - SEATBACK

23 - 98

SEATS

RS

INSTALLATION

BENCH SEAT & 50/50 SPLIT

(1) Position the seat cushion cover on the cushion.
(2) Engage the J-strap retainers.
(3) Steam wrinkles from seat cushion, if necessary.
(4) Install seat risers. (Refer to 23 - BODY/SEATS/

BENCH SEAT RISER - 50/50 SPLIT - INSTALLA-
TION) and (Refer to 23 - BODY/SEATS/BENCH
SEAT RISER - SECOND ROW - INSTALLATION)
and (Refer to 23 - BODY/SEATS/BENCH SEAT
RISER - THIRD ROW - INSTALLATION)

(5) Install seat back. (Refer to 23 - BODY/SEATS/

BENCH SEAT BACK - INSTALLATION)

(6) Install seat into vehicle.

QUAD BUCKET

(1) Position the seat cushion cover on the cushion.
(2) Engage the J-strap retainers.
(3) Steam wrinkles from seat cushion, if necessary.
(4) Install seat risers. (Refer to 23 - BODY/SEATS/

QUAD BUCKET SEAT RISER - INSTALLATION)

(5) Install seat back. (Refer to 23 - BODY/SEATS/

BUCKET SEAT BACK - QUAD BUCKET - INSTAL-
LATION)

(6) Install seat into vehicle.

BENCH SEAT RISER - 50/50
SPLIT

REMOVAL

(1) Remove the seat from the vehicle. Refer to the

Owners Manual for proper procedures.

(2) Unclip the seat cushion cover j-strap. (Fig. 34).
(3) Remove the six bolts and remove the riser.

INSTALLATION

(1) Place the riser onto the seat install the bolts

and tighten to 48 N·m (35 ft. lbs.) torque.

(2) Clip seat cusion cover j-strap onto the riser.
(3) Install the seat into the vehicle. Refer to the

Owner’s Manual for proper procedure.

BENCH SEAT RISER - SECOND
ROW

REMOVAL

(1) Remove seat from vehicle. Refer to Owner’s

Manual for proper procedures.

(2) Place seat bottom side up on a clean covered

work surface.

(3) Remove bolts attaching seat riser to seat cush-

ion frame (Fig. 35).

(4) Remove riser from seat.

Fig. 34 BENCH SEAT RISER - 50/50 SPLIT

1 - SEAT CUSHION COVER CLIP
2 - SEAT RISER BOLTS
3 - SEAT RISER

Fig. 35 BENCH SEAT RISER - SECOND ROW

1 - RISER
2 - FIRST ROW BENCH SEAT
3 - RISER BOLTS

RS

SEATS

23 - 99

SEAT CUSHION COVER - QUAD BUCKET, 50/50 SPLIT, BENCH (Continued)

 

 

 

 

 

 

 

Content   ..  456  457  458  459   ..