Porshe 911 (997). Manual - part 1042

13. Clip in cable duct -29- .

Securing ground point

14. Secure ground point -13- at left and right.

14.1. Connect ground straps and screw down fastening nut. → Tightening torque: 9 (6.5 ftlb.) Nm

15. Plug in connector on wiper motor for rear window washer -12- until it engages correctly. → 923419

Removing and installing wiper motor for rear window washer - section on "Installing"

16. Plug in connector on subwoofer -10- until it engages firmly. → 913619 Removing and installing

subwoofer - section on "Installing"

Connecting PASM plug connection

17. Connect PASM plug connection -9- at left and right.

17.1. Connect PASM plug connection -9- until it engages securely.

18. Plug in connector on DME control module -7- until it engages securely. → 247019 Removing and

installing DME control module - section on "Installing" [997310 997311 997320 997321 997611 997620
997621]→ 247019 Removing and installing DME control module - section on "Installing" [997610]

19. Push in plug connection for rear window heating -6- at left and right until it engages securely. → 648619

Removing and installing rear window - section on "Installing"

20. Plug in connector on seat-belt tensioner -3- at left and right. → 691319 Removing and installing

front three-point seat belt with tensioner - section on "Installing"

20.1. Fit rubber sleeve -30- .

20.2. Plug in connector on seat-belt tensioner -3- at left and right until it engages securely.

21. Attach connector to Tiptronic control unit -2- and lock it until it engages firmly. → 373019

Removing and installing transmission control module - section on "Installing"

Diagnostic system: reading out fault memory and activating systems

Installing rear wire harness

4325

Connecting plug connection for main wire harness to rear wire harness

22. Push plug connection for main wire harness to rear wire harness -1- together at left and right.

22.1. Push plug connection for main wire harness to rear wire harness -1- together and lock it.

Installing wire harness for auxiliary stop light (Cabriolet)

Overview of wire harness for auxiliary stop light

1

-

Connector for auxiliary stop light

2

-

Rubber sleeve

3

-

Plug connection between wire harness for auxiliary stop light and rear wire
harness

Diagnostic system: reading out fault memory and activating systems

Installing wire harness for auxiliary stop light (Cabriolet)

4326

Pushing together plug connection between wire harness for auxiliary stop light and rear wire harness

1. Route wire harness for auxiliary stop light and push together wire harness plug connection for auxiliary

stop light to rear wire harness -3- .

1.1. Press wire harness for auxiliary stop light into fastening part -arrow

A-

 .

1.2. Push together plug connection between wire harness for auxiliary stop light and rear wire harness

-arrows B-

 .

1.3. Fasten wire harness for auxiliary stop light with two new tie-wraps.

Fitting rubber sleeve on wire harness for auxiliary stop light

2. Fit rubber sleeve -2- of the wire harness for auxiliary stop light and fasten wire harness for auxiliary stop

light.

2.1. Slide in wire harness for auxiliary stop light from below into the convertible top compartment lid and fit

rubber sleeve -arrow A- .

2.2. Push on wire harness for auxiliary stop light with the holder onto the convertible top compartment lid

-arrow B-

 .

Installing wire harness for roll-over protection system (cabriolet)

Installation Location:

Diagnostic system: reading out fault memory and activating systems

Installing wire harness for roll-over protection system (cabriolet)

4327

Overview of plugs for wire harness for roll-over protection system

1

- Wire harness for roll-over protection system

2

- Plug connection for rear side panel flap

3

- Hardtop mount plug connection

4

- Retaining clips

5

- Roll-over bar connector

6

- Convertible top control unit connector

7

- Plug connection for wire harness for roll-over protection system to rear wire harness

8

- Plug connection for motor for convertible-top compartment lid drive mechanism

1. Position wire harness for roll-over protection system -1- on the frame and clip in at the retaining

clips -4- .

2. Push in plug connections for rear side panel flap -2- at left and right until they engage securely.

→ 614219 Removing and installing rear side panel flap - section on "Installing"

3. Push in hardtop mount plug connection -3- until it engages securely. → 611719 Removing and installing

mount for hardtop - section on "Installing"

Completing the vehicle

1. Insert insulating elements in the area of the rear wire harness.

Diagnostic system: reading out fault memory and activating systems

Completing the vehicle

4328