Nissan Quest E52. Manual - part 997

PWC-100

< DTC/CIRCUIT DIAGNOSIS >

[DRIVER SIDE WINDOW ANTI-PINCH]

FRONT POWER WINDOW SWITCH (PASSENGER SIDE)

YES

>> Check intermittent incident. Refer to 

GI-42, "Intermittent Incident"

.

NO

>> Replace front power window switch (passenger side). Refer to 

PWC-123, "Removal and Installa-

tion"

.

Component Inspection

INFOID:0000000009653374

1.

CHECK FRONT POWER WINDOW SWITCH (PASSENGER SIDE)

1.

Turn ignition switch OFF.

2.

Disconnect front power window switch (passenger side) connector.

3.

Check front power window switch (passenger side) terminals under the following conditions.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace front power window switch (passenger side). Refer to 

PWC-123, "Removal and Installa-

tion"

.

Front power window switch (passenger side)

Condition

Continuity

Terminal

8

7

UP

Existed

11

6

11

6

NEUTRAL

12

7

8

6

DOWN

12

7

SLIDING DOOR POWER WINDOW SWITCH

PWC-101

< DTC/CIRCUIT DIAGNOSIS >

[DRIVER SIDE WINDOW ANTI-PINCH]

C

D

E

F

G

H

I

J

L

M

A

B

PWC

N

O

P

SLIDING DOOR POWER WINDOW SWITCH

Component Function Check

INFOID:0000000009653375

1.

 CHECK FUNCTION

Check sliding door power window motor operation with sliding door power window switch.
Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Refer to 

PWC-101, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000009653376

1.

CHECK SLIDING DOOR POWER WINDOW SWITCH INPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect sliding door power window switch connector.

3.

Turn ignition switch ON.

4.

Check voltage between sliding door power window switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK SLIDING DOOR POWER WINDOW SWITCH CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect power window main switch connector.

3.

Check continuity between sliding door power window switch harness connector and power window main
switch harness connector.

4.

Check continuity between sliding door power window switch harness connector and ground.

(+)

(-)

Condition

Voltage (V)

Sliding door power window switch

Connector

Terminal 

LH

D88

2

Ground

Power window main 
switch
(sliding door LH side)

NEUTRAL

0 – 1

UP

9 – 16

3

NEUTRAL

0 – 1

DOWN

9 – 16

RH

D108

2

Power window main 
switch
(sliding door RH side)

NEUTRAL

0 – 1

UP

9 – 16

3

NEUTRAL

0 – 1

DOWN

9 – 16

Sliding door power window switch

Power window main switch

Continuity

Connector

Terminal

Connector

Terminal

LH

D88

2

D5

1

Existed

3

3

RH

D108

2

7

3

5

PWC-102

< DTC/CIRCUIT DIAGNOSIS >

[DRIVER SIDE WINDOW ANTI-PINCH]

SLIDING DOOR POWER WINDOW SWITCH

Is the inspection result normal?

YES

>> Replace power window main switch. Refer to 

PWC-123, "Removal and Installation"

.

NO

>> Repair or replace harness.

3.

CHECK SLIDING DOOR POWER WINDOW SWITCH

Check sliding door power window switch.
Refer to 

PWC-102, "Component Inspection"

.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-42, "Intermittent Incident"

.

NO

>> Replace sliding door power window switch. Refer to 

PWC-124, "Removal and Installation"

.

Component Inspection

INFOID:0000000009653377

1.

CHECK SLIDING DOOR POWER WINDOW SWITCH

1.

Turn ignition switch OFF.

2.

Disconnect sliding door power window switch connector.

3.

Check sliding door power window switch terminals under the following conditions.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace sliding door power window switch. Refer to 

PWC-124, "Removal and Installation"

.

Sliding door power window switch

Ground

Continuity

Connector

Terminal

LH

D88

2

Not existed

3

RH

D108

2

3

Sliding door power window switch

Condition

Continuity

Terminal

1

5

UP

Existed

3

4

2

5

NEUTRAL

3

4

1

4

DOWN

2

5

POWER WINDOW MOTOR

PWC-103

< DTC/CIRCUIT DIAGNOSIS >

[DRIVER SIDE WINDOW ANTI-PINCH]

C

D

E

F

G

H

I

J

L

M

A

B

PWC

N

O

P

POWER WINDOW MOTOR

DRIVER SIDE

DRIVER SIDE : Component Function Check

INFOID:0000000009653378

1.

 CHECK FUNCTION

Check front power window motor (driver side) operation with power window main switch.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Refer to 

PWC-103, "DRIVER SIDE : Diagnosis Procedure"

.

DRIVER SIDE : Diagnosis Procedure

INFOID:0000000009653379

1.

CHECK FRONT POWER WINDOW MOTOR (DRIVER SIDE) INPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect front power window motor (driver side) connector.

3.

Turn ignition switch ON.

4.

Check voltage between front power window motor (driver side) harness connector and ground.

Is the inspection result normal?

YES

>> Replace front power window motor (driver side). Refer to 

GW-29, "Removal and Installation"

.

NO

>> GO TO 2.

2.

CHECK FRONT POWER WINDOW MOTOR (DRIVER SIDE) CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect power window main switch connector.

3.

Check continuity between front power window motor (driver side) harness connector and power window
main switch harness connector.

4.

Check continuity between front power window motor (driver side) harness connector and ground.

Is the inspection result normal?

YES

>> Replace power window main switch. Refer to 

PWC-123, "Removal and Installation"

.

NO

>> Repair or replace harness.

PASSENGER SIDE

(+)

(-)

Condition

Voltage (V)

Front power window motor (driver side)

Connector

Terminal

D7

1

Ground

Power window main 
switch
(driver side)

NEUTRAL

0 – 1

DOWN

9 – 16

2

NEUTRAL

0 – 1

UP

9 – 16

Front power window motor (driver side)

 Power window main switch

Continuity

Connector

Terminal

Connector

Terminal

D7

1

D5

12

Existed

2

16

Front power window motor (driver side)

Ground

Continuity

Connector

Terminal

D7

1

Not existed

2