Nissan Versa Note. Manual - part 819

TM-156

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F11A]

P0712 TRANSMISSION FLUID TEMPERATURE SENSOR A

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> There is a malfunction of CVT fluid temperature sensor. Replace transaxle assembly. Refer to

TM-252, "Removal and Installation"

.

CVT unit

Condition

Resistance

(Approx.)

Terminal

12 – 18

CVT fluid temperature: 20

°C (68°C)

6.5 k

Ω

CVT fluid temperature: 50

°C (122°C)

2.2 k

Ω

CVT fluid temperature: 80

°C (176°C)

0.87 k

Ω

P0713 TRANSMISSION FLUID TEMPERATURE SENSOR A

TM-157

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F11A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

P0713 TRANSMISSION FLUID TEMPERATURE SENSOR A

DTC Logic

INFOID:0000000009019686

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at

least 10 seconds, then perform the next test.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

1. Start the engine.

2. Maintain the following condition for 10 seconds or more.

3. Stop the vehicle.

4. Check the first trip DTC.
Is “P0713” detected?

YES

>> Go to 

TM-155, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009019687

1.

CHECK CIRCUIT BETWEEN TCM AND CVT UNIT (PART 1)

1. Turn ignition switch OFF.

2. Disconnect TCM connector and CVT unit connector. 

3. Check continuity between TCM harness connector terminals and CVT unit harness connector terminals.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace malfunctioning part.

2.

CHECK CIRCUIT BETWEEN TCM AND CVT UNIT (PART 2)

1. Turn ignition switch ON.

2. Check voltage between TCM harness connector terminal and ground.

DTC

Trouble diagnosis name

DTC detection condition

Possible causes

P0713

Transmission Fluid Tempera-
ture Sensor A Circuit High

The CVT fluid temperature identified by the 
TCM is 

−40°C (−40°F) or less continuously for 

5 seconds or more under the following diagno-
sis conditions:
• Diagnosis conditions
- Ignition switch: ON
- Vehicle speed: More than 10 km/h (7 MPH)
- TCM power supply voltage: More than 11 V

• Harness or connector

(CVT fluid temperature sensor circuit is 
open or shorted to power supply)

• CVT fluid temperature sensor

Vehicle speed

: 20 km/h (12 MPH) or more 

TCM

CVT unit

Continuity

Connector

Terminal

Connector

Terminal

F44

12

F46

12

Existed

11

18

TM-158

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F11A]

P0713 TRANSMISSION FLUID TEMPERATURE SENSOR A

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace malfunctioning part.

3.

CHECK CVT FLUID TEMPERATURE SENSOR

Check CVT fluid temperature sensor. Refer to 

TM-158, "Component Inspection (CVT Fluid Temperature Sen-

sor)"

.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-41, "Intermittent Incident"

.

NO

>> Repair or replace malfunctioning parts.

Component Inspection (CVT Fluid Temperature Sensor) 

INFOID:0000000009019688

1.

CHECK CVT FLUID TEMPERATURE SENSOR

Check resistance between CVT unit connector terminals. 

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> There is a malfunction of CVT fluid temperature sensor. Replace transaxle assembly. Refer to

TM-252, "Removal and Installation"

.

+

−

Voltage

(Approx.)

TCM

Connector

Terminal

F44

12

Ground

0 V

CVT unit

Condition

Resistance

(Approx.)

Terminal

12 – 18

CVT fluid temperature: 20

°C (68°C)

6.5 k

Ω

CVT fluid temperature: 50

°C (122°C)

2.2 k

Ω

CVT fluid temperature: 80

°C (176°C)

0.87 k

Ω

P0715 INPUT SPEED SENSOR A

TM-159

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F11A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

P0715 INPUT SPEED SENSOR A

DTC Logic

INFOID:0000000009019689

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CAUTION:

Be careful of the driving speed.

1.

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at

least 10 seconds, then perform the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

1. Start the engine.

2. Drive the vehicle.

3. Maintain the following conditions for 10 seconds or more.

4. Stop the vehicle.

5. Check the first trip DTC.
Is “P0715” detected?

YES

>> Go to 

TM-159, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009019690

1.

CHECK PRIMARY SPEED SENSOR POWER CIRCUIT 

1. Turn ignition switch OFF.

2. Disconnect primary speed sensor connector.

3. Turn ignition switch ON.

4. Check voltage between primary speed sensor harness connector terminal and ground. 

Is the inspection result normal?

DTC

Trouble diagnosis name

DTC detection condition

Possible causes

P0715

Input/Turbine Speed Sensor A 
Circuit

The primary speed sensor value is less than 
150 rpm continuously for 5 seconds or more 
under the following diagnosis conditions:
• Diagnosis conditions
- Secondary pulley speed: 1,000 rpm or more
- TCM power supply voltage: More than 11 V

• Harness or connector

(Primary speed sensor circuit is open 
or shorted) 

• Primary speed sensor

The primary speed sensor value is 240 rpm or 
less continuously for 500 msec or more under 
the following diagnosis conditions:
• Diagnosis conditions
- 10-msec-ago primary pulley speed: 1,000 

rpm or more

- TCM power supply voltage: More than 11 V

Selector lever

: “L” POSITION

Vehicle speed

: 40 km/h (25 MPH) or more

+

−

Voltage

Primary speed sensor

Connector

Terminal

F50

3

Ground

10 – 16 V