Nissan Versa Note. Manual - part 817

 

  Index      Nissan     Nissan Versa Note (2014 year) - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  815  816  817  818   ..

 

 

Nissan Versa Note. Manual - part 817

 

 

TM-148

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F11A]

P0705 TRANSMISSION RANGE SENSOR A

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> There is a malfunction of transmission range switch. Replace transaxle assembly. Refer to 

TM-

252, "Removal and Installation"

.

4 – 5

Manual lever: “P” position

Existed

Other than the above

Not existed

4 – 8

Manual lever: “R” position

Existed

Other than the above

Not existed

4 – 9

Manual lever: “N position

Existed

Other than the above

Not existed

4 – 2

Manual lever: “D” position

Existed

Other than the above

Not existed

4 – 6

Manual lever: “L” position

Existed

Other than the above

Not existed

Transmission range switch

Condition

Continuity

Terminal

P0706 TRANSMISSION RANGE SENSOR A

TM-149

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F11A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

P0706 TRANSMISSION RANGE SENSOR A

DTC Logic

INFOID:0000000009019677

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at

least 10 seconds, then perform the next test.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

1. Start the engine.

2. Maintain the following conditions.

3. Shift the selector lever through entire positions from “P” to “L”. (Hold the selector lever at each position for

35 seconds or more.)

4. Check the first trip DTC.
Is “P0706” detected?

YES

>> Go to 

TM-149, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009019678

1.

ADJUSTMENT OF CONTROL CABLE

Adjust control cable. Refer to 

TM-230, "Inspection"

.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

1. Turn ignition switch ON.

2. Select “Self Diagnostic Results” in “TRANSMISSION”.

3. Touch “Erase”.

4. Perform "DTC CONFIRMATION PROCEDURE". Refer to 

TM-149, "DTC Logic"

.

Is “P0706” detected?

YES

>> GO TO 3.

NO

>> INSPECTION END

DTC

Trouble diagnosis name

DTC detection condition

Possible causes

P0706

Transmission Range Sensor 
A Circuit Range/Performance

All range signals stay OFF continuously for 30 
seconds under the following diagnosis condi-
tion 1 and 2:
• Diagnosis condition 1 (continued for 30 sec-

onds or more) 

- TCM power supply voltage: More than 11 V
• Diagnosis condition 2 (continued for 2 sec-

onds or more) 

- Vehicle speed: Less than 3 km/h (2 MPH)
- Accelerator pedal position: 0.6/8 or less
- Idle switch: ON 
- Stop lamp switch: ON

• Harness or connector

(Open circuit between ignition switch 
and transmission range switch/open 
circuit between transmission range 
switch and TCM)

• Transmission range switch
• Control cable

Accelerator pedal position

: 0.0/8

Brake pedal

: Depressed

Vehicle speed

: 0 km/h (0 MPH)

TM-150

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F11A]

P0706 TRANSMISSION RANGE SENSOR A

3.

CHECK POWER CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect transmission range switch connector.

3. Turn ignition switch ON.

4. Check voltage between transmission range switch harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> GO TO 7.

4.

CHECK CIRCUIT BETWEEN TRANSMISSION RANGE SWITCH AND TCM (PART 1)

1. Turn ignition switch OFF.

2. Disconnect TCM connector.

3. Check continuity between transmission range switch harness connector terminals and TCM harness con-

nector terminals.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace malfunctioning parts.

5.

CHECK CIRCUIT BETWEEN TRANSMISSION RANGE SWITCH AND TCM (PART 2) 

Check continuity between transmission range switch harness connector terminals and ground.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace malfunctioning parts.

6.

CHECK TRANSMISSION RANGE SWITCH

Check transmission range switch. Refer to 

TM-151, "Component Inspection (Transmission Range Switch)"

.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-41, "Intermittent Incident"

.

NO

>> Repair or replace malfunctioning parts.

+

Voltage

Transmission range switch

Connector

Terminal

F49

4

Ground

10 – 16 V

Transmission range switch

TCM

Continuity

Connector

Terminal

Connector

Terminal

F49

2

F44

4

Existed

5

7

6

6

8

6

9

5

Transmission range switch

Continuity

Connector

Terminal

F49

2

Ground

Not existed

5

6

8

9

P0706 TRANSMISSION RANGE SENSOR A

TM-151

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F11A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

7.

CHECK CIRCUIT BETWEEN IPDM E/R AND TRANSMISSION RANGE SWITCH

1. Disconnect IPDM E/R connector.

2. Check continuity between IPDM E/R harness connector and transmission range switch.

Is the check result normal?

YES

>> GO TO 8.

NO

>> Repair or replace malfunctioning parts.

8.

DETECT MALFUNCTIONING ITEMS

Check the following items:

• Open circuit or short circuit in harness between ignition switch and IPDM E/R. Refer to 

PG-17, "Wiring Dia-

gram — Ignition Power Supply —"

.

• Short circuit in harness between IPDM E/R harness connector terminal 21 and transmission range switch

harness connector terminal 4.

• 10A fuse (No. 49, IPDM E/R). Refer to 

PG-60, "IPDM E/R Terminal Arrangement"

.

• IPDM E/R
Is the check result normal?

YES

>> Check intermittent incident. Refer to 

GI-41, "Intermittent Incident"

.

NO

>> Repair or replace malfunctioning parts.

Component Inspection (Transmission Range Switch)

INFOID:0000000009019679

1.

CHECK TRANSMISSION RANGE SWITCH

Check continuity between transmission range switch connector terminals.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> There is a malfunction of transmission range switch. Replace transaxle assembly. Refer to 

TM-

252, "Removal and Installation"

.

IPDM E/R

Transmission range switch

Continuity

Connector

Terminal

Connector

Terminal

E45

21

F49

4

Existed

Transmission range switch

Condition

Continuity

Terminal

7 – 10

Manual lever: “P” and “N” positions

Existed

Other than the above

Not existed

4 – 5

Manual lever: “P” position

Existed

Other than the above

Not existed

4 – 8

Manual lever: “R” position

Existed

Other than the above

Not existed

4 – 9

Manual lever: “N position

Existed

Other than the above

Not existed

4 – 2

Manual lever: “D” position

Existed

Other than the above

Not existed

4 – 6

Manual lever: “L” position

Existed

Other than the above

Not existed

 

 

 

 

 

 

 

Content   ..  815  816  817  818   ..