Nissan Versa Note. Manual - part 701

B2601 SHIFT POSITION

SEC-83

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

2.

CHECK CVT SHIFT SELECTOR CIRCUIT (IPDM E/R)

1. Disconnect IPDM E/R connector.

2. Check continuity between CVT shift selector (park position switch) harness connector and IPDM E/R har-

ness connector.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

REPLACE BCM

1. Replace BCM. Refer to 

BCS-70, "Removal and Installation"

.

2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT. Refer to the CON-

SULT Immobilizer mode and follow the on-screen instructions.

3. Perform DTC CONFIRMATION PROCEDURE for DTC B2601. Refer to 

SEC-82, "DTC Logic"

.

Is DTC B2601 detected again?

YES

>> Replace IPDM E/R. Refer to 

PCS-31, "Removal and Installation"

.

NO

>> Inspection End.

CVT shift selector (park position switch)

IPDM E/R

Continuity

Connector

Terminal

Connector

Terminal

M38

8

E47

80

Yes

SEC-84

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

B2602 SHIFT POSITION

B2602 SHIFT POSITION

DTC Logic

INFOID:0000000009705887

DTC DETECTION LOGIC

NOTE:

• If DTC B2602 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to

BCS-60, "DTC Logic"

.

• If DTC B2602 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to

BCS-61, "DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Start engine.

2. Drive vehicle at a speed of 4 km/h (2.5 MPH) or more for 10 seconds or more.

3. Check DTC in Self Diagnostic Result mode of BCM using CONSULT.
Is DTC detected?

YES

>> Go to 

SEC-84, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000009705888

Regarding Wiring Diagram information, refer to 

SEC-40, "Wiring Diagram"

.

1.

CHECK DTC OF ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)

Check DTC in Self Diagnostic Result mode of ABS using CONSULT.
Is DTC detected?

YES

>> Perform the trouble diagnosis related to the detected DTC. Refer to 

BRC-41, "DTC Index"

.

NO

>> GO TO 2.

2.

CHECK DTC OF COMBINATION METER

Check DTC in Self Diagnostic Result mode of METER/M&A using CONSULT.
Is DTC detected?

YES

>> Perform the trouble diagnosis related to the detected DTC. Refer to 

MWI-21, "DTC Index"

.

NO

>> GO TO 3.

3.

CHECK CVT SHIFT SELECTOR POWER SUPPLY

1. Turn ignition switch OFF.

2. Disconnect CVT shift selector (park position switch) connector.

3. Check voltage between CVT shift selector (park position switch) harness connector and ground.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B2602

SHIFT P DIAG

BCM detects the following status for 10 seconds.
• Selector lever is in the P position
• Vehicle speed is 4 km/h (2.5 MPH) or more
• Ignition switch is in the ON position

• Harness or connectors

(The CAN communication line is 
open or shorted.)

• Harness or connectors 

[CVT shift selector (park position 
switch) circuit is open or shorted.]

• CVT shift selector (park position 

switch)

• Combination meter

B2602 SHIFT POSITION

SEC-85

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> GO TO 4.

4.

CHECK CVT SHIFT SELECTOR POWER SUPPLY CIRCUIT

1. Disconnect BCM connector.

2. Check continuity between CVT shift selector (park position switch) harness connector and BCM harness

connector.

3. Check continuity between CVT shift selector (park position switch) harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace harness.

5.

REPLACE BCM

1. Replace BCM. Refer to 

PCS-31, "Removal and Installation"

.

2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT. Refer to the CON-

SULT Immobilizer mode and follow the on-screen instructions.

>> Inspection End.

6.

CHECK CVT SHIFT SELECTOR CIRCUIT

1. Disconnect BCM connector and IPDM E/R connector.

2. Check continuity between CVT shift selector (park position switch) harness connector and BCM harness

connector.

3. Check continuity between CVT shift selector (park position switch) harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Repair or replace harness.

7.

CHECK CVT SHIFT SELECTOR (PARK POSITION SWITCH)

Refer to 

SEC-86, "Component Inspection"

.

Is the inspection result normal?

(+)

(–)

Voltage (V)

(Approx.)

CVT shift selector (park position switch)

Connector

Terminal

M38

7

Ground

12

CVT shift selector (park position switch)

BCM

Continuity

Connector

Terminal

Connector

Terminal

M38

7

M98

104

Yes

CVT shift selector (park position switch)

Ground

Continuity

Connector

Terminal

M38

7

No

CVT shift selector (park position switch)

BCM

Continuity

Connector

Terminal

Connector

Terminal

M38

8

M97

37

Yes

CVT shift selector (park position switch)

Ground

Continuity

Connector

Terminal

M38

8

No

SEC-86

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

B2602 SHIFT POSITION

YES

>> GO TO 8.

NO

>> Replace CVT shift selector. Refer to 

TM-229, "Removal and Installation"

.

8.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-41, "Intermittent Incident"

.

>> Inspection End.

Component Inspection

INFOID:0000000009705889

1.

CHECK CVT SHIFT SELECTOR (PARK POSITION SWITCH)

1. Turn ignition switch OFF.

2. Disconnect CVT shift selector connector.

3. Check continuity between CVT shift selector (park position switch) terminals.

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Replace CVT shift selector. Refer to 

TM-229, "Removal and Installation"

.

CVT shift selector (park position switch)

Condition

Continuity

Terminal

7

8

Selector lever: P position

Selector button: Released

No

Selector button: Pressed

Yes

Selector lever: Other than P position