Nissan Rogue. Manual - part 932

MWI

THE FUEL GAUGE DOES NOT MOVE

MWI-75

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

SYMPTOM DIAGNOSIS

THE FUEL GAUGE DOES NOT MOVE

Description

INFOID:0000000011279831

Fuel gauge does not move from a certain position.

Diagnosis Procedure

INFOID:0000000011279832

1.

CHECK COMBINATION METER INPUT SIGNAL

Perform component function check. Refer to 

MWI-63, "Component Function Check"

.

Does monitor value match fuel gauge reading?

YES

>> GO TO 2.

NO

>> Replace combination meter. Refer to 

MWI-84, "Removal and Installation"

.

2.

CHECK FUEL LEVEL SENSOR UNIT CIRCUITS

Check the fuel level sensor circuits. Refer to 

MWI-63, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness or connector.

3.

CHECK FUEL LEVEL SENSOR UNIT

Check the fuel level sensor unit. Refer to 

MWI-64, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Replace fuel level sensor unit. Refer to 

FL-5, "Removal and Installation"

.

4.

CHECK FLOAT INTERFERENCE

Check that the float arm does not interfere with or binds to other components in the fuel tank.
Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-44, "Intermittent Incident"

.

NO

>> Repair or replace malfunctioning parts.

MWI-76

< SYMPTOM DIAGNOSIS >

THE OIL PRESSURE WARNING CONTINUES DISPLAYING, OR DOES NOT DIS-

PLAY

THE OIL PRESSURE WARNING CONTINUES DISPLAYING, OR DOES
NOT DISPLAY

Description

INFOID:0000000011279833

• The low oil pressure warning message stays on when oil pressure is normal.

• The low oil pressure warning message stays off when oil pressure is low.

Diagnosis Procedure

INFOID:0000000011279834

1.

CHECK COMBINATION METER INPUT

1. Start the engine.

2. Select “METER/M&A” using CONSULT.

3. Select “OIL W/L” in “Data Monitor”.

4. Check the “OIL W/L” status according to the following condition:

Is the inspection result normal?

YES

>> Perform “Self Diagnosis” of “ECM”. Refer to 

EC-69, "CONSULT Function"

.

NO

>> Replace combination meter. Refer to 

MWI-84, "Removal and Installation"

.

Monitor Item

Condition

CONSULT

OIL W/L

Engine running

Off

MWI

THE PARKING BRAKE RELEASE WARNING CONTINUES DISPLAYING, OR 

DOES NOT DISPLAY

MWI-77

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

THE PARKING BRAKE RELEASE WARNING CONTINUES DISPLAYING,
OR DOES NOT DISPLAY

Description

INFOID:0000000011279835

• The parking brake warning is displayed during vehicle travel even though the parking brake is released.

• The parking brake warning is not displayed even though driving the vehicle with the parking brake applied.

Diagnosis Procedure

INFOID:0000000011279836

1.

CHECK PARKING BRAKE WARNING LAMP OPERATION

1. Start engine.

2. Check the operation of the brake warning lamp while operating the parking brake.

Is the inspection result normal?

YES

>> Replace combination meter. Refer to 

MWI-84, "Removal and Installation"

.

NO

>> GO TO 2.

2.

CHECK PARKING BRAKE SWITCH SIGNAL CIRCUIT

1. Turn ignition switch OFF.

2. Check the parking brake switch signal circuit. Refer to 

MWI-65, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness or connector.

3.

CHECK PARKING BRAKE SWITCH UNIT

Check the parking brake switch. Refer to 

MWI-65, "Component Inspection"

. 

Is the inspection result normal?

YES

>> Replace combination meter. Refer to 

MWI-84, "Removal and Installation"

.

NO

>> Replace parking brake switch. Refer to 

PB-7, "Exploded View"

.

Condition

Warning lamp status

Parking brake applied

ON

Parking brake released

OFF

MWI-78

< SYMPTOM DIAGNOSIS >

THE LOW WASHER FLUID WARNING CONTINUES DISPLAYING, OR DOES 

NOT DISPLAY

THE LOW WASHER FLUID WARNING CONTINUES DISPLAYING, OR
DOES NOT DISPLAY

Description

INFOID:0000000011279837

• The warning is still displayed even after washer fluid is added.

• The warning is not displayed even though the washer tank is empty.

Diagnosis Procedure

INFOID:0000000011279838

1.

CHECK WASHER FLUID LEVEL SWITCH SIGNAL CIRCUIT

Check the washer fluid level switch signal circuit. Refer to 

MWI-73, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace harness or connector.

2.

CHECK WASHER FLUID LEVEL SWITCH UNIT

Check the washer fluid level switch. Refer to 

MWI-73, "Component Inspection"

.

Is the inspection result normal?

YES

>> Replace combination meter. Refer to 

MWI-84, "Removal and Installation"

.

NO

>> Replace washer fluid level switch. Refer to 

WW-57, "Removal and Installation"

.