Nissan Rogue. Manual - part 930

 

  Index      Nissan     Nissan Rogue (2015 year) - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  928  929  930  931   ..

 

 

Nissan Rogue. Manual - part 930

 

 

MWI

AMBIENT SENSOR SIGNAL CIRCUIT

MWI-67

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

AMBIENT SENSOR SIGNAL CIRCUIT

Description

INFOID:0000000011279820

It detects outside air temperature and converts it into a resistance value which is then input into the combina-

tion meter.

Diagnosis Procedure

INFOID:0000000011279821

Regarding Wiring Diagram information, refer to 

MWI-33, "Wiring Diagram"

.

1.

CHECK AMBIENT SENSOR SIGNAL CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect combination meter connector and ambient sensor connector.

3. Check continuity between combination meter harness connector and ambient sensor harness connector.

4. Check continuity between combination meter harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace harness or connector.

2.

CHECK AMBIENT SENSOR SIGNAL GROUND CIRCUIT

Check continuity between combination meter harness connector and ambient sensor harness connector.

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Repair or replace harness or connector.

Component Inspection

INFOID:0000000011279822

1.

CHECK AMBIENT SENSOR

1. Turn ignition switch OFF.

2. Disconnect ambient sensor connector.

3. Check resistance between ambient sensor terminals.

Combination meter

Ambient sensor

Continuity

Connector

Terminal

Connector

Terminal

M76

15

E76

1

Yes

Combination meter

Ground

Continuity

Connector

Terminal

M76

15

No

Combination meter

Ambient sensor

Continuity

Connector

Terminal

Connector

Terminal

M76

20

E76

2

Yes

MWI-68

< DTC/CIRCUIT DIAGNOSIS >

AMBIENT SENSOR SIGNAL CIRCUIT

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Replace ambient sensor. Refer to 

HAC-104, "Removal and Installation"

.

Ambient sensor

Resistance: k

Terminal

Condition

Temperature: 

°C (°F)

1

2

 

−15 (5)

12.73

 

−10 (14)

9.92

 

−5 (23)

7.80

0 (32)

6.19

5 (41)

4.95

10 (50)

3.99

15 (59)

3.24

20 (68)

2.65

25 (77)

2.19

30 (86)

1.81

35 (95)

1.51

40 (104)

1.27

45 (113)

1.07

MWI

METER CONTROL SWITCH SIGNAL CIRCUIT

MWI-69

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

METER CONTROL SWITCH SIGNAL CIRCUIT

Diagnosis Procedure

INFOID:0000000011279823

Regarding Wiring Diagram information, refer to 

MWI-33, "Wiring Diagram"

.

1.

CHECK METER CONTROL SWITCH SIGNAL 

1. Turn ignition switch ON.

2. Check voltage between the following terminals of the meter control switch harness connector M3.

Is the inspection result normal?

YES

>> Inspection End.

NO

>> GO TO 2.

2.

CHECK METER CONTROL SWITCH HARNESS

1. Turn ignition switch OFF.

2. Disconnect combination meter harness connector M77 and meter control switch harness connector M3.

3. Check continuity between combination meter harness connector M77 and meter control switch harness

connector M3. 

4. Check continuity between combination meter harness connector and ground.

Is the inspection result normal? 

YES

>> Inspection End.

NO

>> Repair or replace harness or connectors.

Meter control switch 

Condition

Voltage

(Approx.)

Connector

Terminals

(+)

(

−)

M3

7

4

When illumination control switch (

−) is pressed

0 V

Other than the above

5 V

5

When trip reset switch is pressed

0 V

Other than the above

5 V

6

When illumination control switch (+) is pressed

0 V

Other than the above

5 V

Combination meter

Meter control switch

Continuity

Connector

Terminal

Connector

Terminal

M77

18

M3

5

Yes

37

7

36

6

17

4

Combination meter

Ground

Continuity

Connector

Terminal

M77

18

No

37

36

17

MWI-70

< DTC/CIRCUIT DIAGNOSIS >

METER CONTROL SWITCH SIGNAL CIRCUIT

Component Inspection

INFOID:0000000011279824

1.

CHECK METER CONTROL SWITCH

1. Turn ignition switch OFF.

2. Disconnect meter control switch connector. 

3. Check meter control switch.

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Replace meter control switch. Refer to 

MWI-85, "Removal and Installation"

.

Meter control switch

Condition

Continuity

Terminals

7

4

When illumination control switch (

−) is pressed

Yes

Other than the above

No

5

When trip reset switch is pressed

Yes

Other than the above

No

6

When illumination control switch (+) is pressed

Yes

Other than the above

No

 

 

 

 

 

 

 

Content   ..  928  929  930  931   ..