Nissan Rogue. Manual - part 649

 

  Index      Nissan     Nissan Rogue (2015 year) - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  647  648  649  650   ..

 

 

Nissan Rogue. Manual - part 649

 

 

POWER SUPPLY AND GROUND CIRCUIT

EXL-225

< DTC/CIRCUIT DIAGNOSIS >

[LED HEADLAMP]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

Check that the following fuse is not blown.

Is the fuse blown?

YES

>> Replace the blown fuse after repairing the affected circuit.

NO

>> GO TO 2.

2.

 CHECK POWER SUPPLY CIRCUIT

1. Disconnect BCM connector M20.

2. Check voltage between BCM connector M20 and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness or connectors.

3.

 CHECK GROUND CIRCUIT

Check continuity between BCM connector M20 and ground.

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Repair or replace harness or connectors.

Terminal No.

Signal name

Fuse No.

161

BCM power supply

7 (10A)

BCM

Ground

Voltage

(Approx.)

Connector

Terminal

M20

161

Battery voltage

BCM

Ground

Continuity

Connector

Terminal

M20

170

Yes

171

EXL-226

< DTC/CIRCUIT DIAGNOSIS >

[LED HEADLAMP]

OPTICAL SENSOR

OPTICAL SENSOR

Component Function Check

INFOID:0000000011421502

1.

CHECK OPTICAL SENSOR SIGNAL BY CONSULT

CONSULT DATA MONITOR

1. Turn ignition switch ON.

2. Select “OPTICAL SENSOR” in “Data Monitor” of “BCM (HEADLAMP)”.

3. Turn lighting switch AUTO.

4. With the optical sensor illuminating, check the monitor status. 

*: Illuminates the optical sensor. The value may be less than the standard value if brightness is weak.

Is the inspection result normal?

YES

>> Optical sensor is normal.

NO

>> Refer to 

EXL-226, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000011421503

1.

CHECK OPTICAL SENSOR POWER SUPPLY INPUT

1. Turn ignition switch ON.

2. Turn lighting switch AUTO.

3. Check voltage between optical sensor harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> GO TO 4.

2.

CHECK OPTICAL SENSOR GROUND INPUT

Check voltage between optical sensor harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 6.

3.

CHECK OPTICAL SENSOR SIGNAL OUTPUT

 With illuminating the optical sensor, check voltage between optical sensor harness connector and ground.

Monitor item

Condition

Voltage (Approx.)

OPTICAL SENSOR

Optical sensor

When illuminating

3.1 V or more *

When shutting off light

0.6 V or less

(+)

(

−)

Voltage

(Approx.)

Optical sensor

Connector

Terminal

M13

1

Ground

5 V

(+)

(

−)

Voltage

(Approx.)

Optical sensor

Connector

Terminal

M13

3

Ground

0 V

OPTICAL SENSOR

EXL-227

< DTC/CIRCUIT DIAGNOSIS >

[LED HEADLAMP]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

*: Illuminate the optical sensor. The value may be less than the standard if brightness is weak.
Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Replace the optical sensor.

4.

CHECK OPTICAL SENSOR OPEN CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect optical sensor connector and BCM connector.

3. Check continuity between optical sensor harness connector and BCM harness connector.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace harness.

5.

CHECK OPTICAL SENSOR SHORT CIRCUIT

Check continuity between optical sensor harness connector and ground.

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-75, "Removal and Installation"

 (with Intelligent Key system) or 

BCS-

135, "Removal and Installation"

 (without Intelligent Key system).

NO

>> Repair or replace harness.

6.

CHECK OPTICAL SENSOR GROUND OPEN CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect optical sensor connector and BCM connector.

3. Check continuity between optical sensor harness connector and BCM harness connector.

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-75, "Removal and Installation"

 (with Intelligent Key system) or 

BCS-

135, "Removal and Installation"

 (without Intelligent Key system).

NO

>> Repair or replace harness.

7.

CHECK OPTICAL SENSOR SIGNAL OPEN CIRCUIT 

1. Turn ignition switch OFF.

2. Disconnect optical sensor connector and BCM connector.

3. Check continuity between optical sensor harness connector and BCM harness connector.

(+)

(

−)

Condition

Voltage

(Approx.)

Optical sensor

Connector

Terminal

M13

2

Ground

Optical sensor

When illuminating

3.1 V or more *

When shutting off light

0.6 V or less

Optical sensor

BCM

Continuity

Connector

Terminal

Connector

Terminal

M13

1

M18

12

Yes

Optical sensor

Ground

Continuity

Connector

Terminal

M13

1

No

Optical sensor

BCM

Continuity

Connector

Terminal

Connector

Terminal

M13

3

M18

30

Yes

EXL-228

< DTC/CIRCUIT DIAGNOSIS >

[LED HEADLAMP]

OPTICAL SENSOR

Is the inspection result normal?

YES

>> GO TO 8.

NO

>> Repair or replace harness.

8.

CHECK OPTICAL SENSOR SHORT CIRCUIT

Check continuity between optical sensor harness connector and ground.

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-75, "Removal and Installation"

 (with Intelligent Key system) or 

BCS-

135, "Removal and Installation"

 (without Intelligent Key system).

NO

>> Repair or replace harness.

Optical sensor

BCM

Continuity

Connector

Terminal

Connector

Terminal

M13

2

M18

19

Yes

Optical sensor

Ground

Continuity

Connector

Terminal

M13

2

No

 

 

 

 

 

 

 

Content   ..  647  648  649  650   ..