Nissan Rogue. Manual - part 319

D L K - 1 1 8

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

B2416 TOUCH SENSOR RH

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> GO TO 4.

4.

CHECK TOUCH SENSOR RH CIRCUIT

1. Disconnect automatic back door control module and touch sensor RH connector.

2. Check continuity between automatic back door control module harness connector and touch sensor RH

harness connector.

3. Check continuity between automatic back door control module harness connector and ground.

Is the inspection result normal?

YES

>> Replace automatic back door control module. Refer to 

DLK-283, "Removal and Installation"

.

NO

>> Repair or replace harness.

5.

CHECK TOUCH SENSOR RH GROUND CIRCUIT

1. Disconnect automatic back door control module and touch sensor RH connector.

2. Check continuity between automatic back door control module harness connector and touch sensor RH

harness connector.

3. Check continuity between automatic back door control module harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace harness.

6.

CHECK TOUCH SENSOR RH GROUND CIRCUIT 2

1. Connect automatic back door control module and touch sensor RH connector.

2. Check voltage between automatic back door control module harness connector and ground.

(+)

(–)

Condition

Voltage

(Approx.)

Touch sensor RH

Automatic back door control mod-

ule

 Connector

Terminal

 Connector

Terminal

D515

1

B55

13

Touch sensor 
RH

Detect obstruc-
tion

1.8 – 5 V

Other than 
above

2.72 – 7.27 V

Automatic back door control module

Touch sensor RH

Continuity 

 Connector

Terminal

Connector

Terminal

B55

1

D515

2

Yes

Automatic back door control module

Ground

Continuity 

 Connector

Terminal

B55

1

No

Automatic back door control module

Touch sensor RH

Continuity 

 Connector

Terminal

Connector

Terminal

B55

13

D515

1

Yes

Automatic back door control module

Ground

Continuity 

 Connector

Terminal

B55

13

No

2015 Rogue NAM

B2416 TOUCH SENSOR RH

DLK-119

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Replace automatic back door control module. Refer to 

DLK-283, "Removal and Installation"

.

7.

CHECK TOUCH SENSOR RH

Refer to 

DLK-119, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 8.

NO

>> Replace touch sensor RH. Refer to 

DLK-271, "TOUCH SENSOR : Removal and Installation"

.

8.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-44, "Intermittent Incident"

.

>> Inspection End.

Component Inspection

INFOID:0000000011278830

1.

CHECK TOUCH SENSOR RH

1. Turn ignition switch OFF.

2. Disconnect touch sensor RH connector.

3. Check resistance between touch sensor RH terminals.

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Replace touch sensor RH. Refer to 

DLK-271, "TOUCH SENSOR : Removal and Installation"

.

(+)

(–)

Voltage

(Approx.)

Automatic back door control module

 Connector

Terminal

B55

13

Ground

0.01 – 0 V

Touch sensor RH

 Condition

Resistance 

(Approx.)

Terminal

1

2

Touch sensor RH

Detect obstruction

380 – 420 k

Ω

Other than above

0.95 – 1.05 k

Ω

2015 Rogue NAM

DLK-120

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

B2417 TOUCH SENSOR LH

B2417 TOUCH SENSOR LH

DTC Logic

INFOID:0000000011278831

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON.

2. Check “Self Diagnostic Result” of “AUTO BACK DOOR” using CONSULT.
Is DTC detected?

YES

>> Refer to 

DLK-120, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000011278832

Regarding Wiring Diagram information, refer to 

DLK-90, "Wiring Diagram"

.

1.

CHECK INSTALLATION OF TOUCH SENSOR LH

Check that touch sensor LH is installed normally.

Refer to 

DLK-271, "TOUCH SENSOR : Removal and Installation"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Refer to 

DLK-271, "TOUCH SENSOR : Removal and Installation"

.

2.

CHECK TOUCH SENSOR MONITOR ITEM

1. Select “AUTO BACK DOOR” using CONSULT.

2. Select “TOUCH SEN LH” in “Data Monitor”.

3. Check that the function operates normally according to the following conditions:

Is the inspection result normal?

YES

>> GO TO 8.

NO

>> GO TO 3.

3.

CHECK TOUCH SENSOR INPUT SIGNAL

1. Turn ignition switch OFF.

2. Check voltage between touch sensor LH harness connector and automatic back door control module har-

ness connector.

DTC

CONSULT display 

description

DTC detecting condition

Possible cause

B2417

TOUCH SEN L 
OPEN

 Automatic back door control module detects a mal-
function of touch sensor LH during automatic oper-
ation of back door.

• Improper installation of touch sen-

sor

• Touch sensor LH
• Harness or connectors
• Automatic back door control mod-

ule

Monitor item

Condition

Status

 TOUCH SEN LH

Touch sensor LH

Other than below

OFF

Detect obstruction

ON

2015 Rogue NAM

B2417 TOUCH SENSOR LH

DLK-121

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> GO TO 4.

4.

CHECK TOUCH SENSOR LH CIRCUIT

1. Disconnect automatic back door control module and touch sensor LH connector.

2. Check continuity between automatic back door control module harness connector and touch sensor LH

harness connector.

3. Check continuity between automatic back door control module harness connector and ground.

Is the inspection result normal?

YES

>> Replace automatic back door control module. Refer to 

DLK-283, "Removal and Installation"

.

NO

>> Repair or replace harness.

5.

CHECK TOUCH SENSOR LH GROUND CIRCUIT

1. Disconnect automatic back door control module and touch sensor LH connector.

2. Check continuity between automatic back door control module harness connector and touch sensor LH

harness connector.

3. Check continuity between automatic back door control module harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace harness.

6.

CHECK TOUCH SENSOR LH GROUND CIRCUIT 2

1. Connect automatic back door control module and touch sensor LH connector.

2. Check voltage between automatic back door control module harness connector and ground.

(+)

(–)

Condition

Voltage

(Approx.)

Touch sensor LH

Automatic back door control mod-

ule

 Connector

Terminal

 Connector

Terminal

D511

2

B55

13

Touch sensor 
LH

Detect obstruc-
tion

1.8 – 5 V

Other than 
above

2.72 – 7.27 V

Automatic back door control module

Touch sensor LH

Continuity 

 Connector

Terminal

Connector

Terminal

B55

2

D511

1

Yes

Automatic back door control module

Ground

Continuity 

 Connector

Terminal

B55

2

No

Automatic back door control module

Touch sensor LH

Continuity 

 Connector

Terminal

Connector

Terminal

B55

13

D511

2

Yes

Automatic back door control module

Ground

Continuity 

 Connector

Terminal

B55

13

No

2015 Rogue NAM