Nissan Rogue. Manual - part 317

DLK-110

< BASIC INSPECTION >

[WITH INTELLIGENT KEY SYSTEM]

CALIBRATION OF AUTOMATIC BACK DOOR POSITION INFORMATION

CALIBRATION OF AUTOMATIC BACK DOOR POSITION INFORMATION

Description

INFOID:0000000011278815

When the following work is performed, it is necessary to perform initial setting of automatic back door position

information to operate automatic back door system:

• After removing and installing or replacing back door assembly.

• After removing and installing or replacing spindle unit.

• After adjustment or position change of the back door hinges or striker.

Work Procedure

INFOID:0000000011278816

1.

STEP 1

Fully close the back door manually.

>> GO TO 2.

2.

STEP 2

1. Select “AUTO BACK DOOR” using CONSULT.

2. Select “RESET AUTO BACK DOOR STATUS” of “Work support”.

3. Touch “START” to erase automatic back door position information.

>> GO TO 3.

3.

STEP 3

Operate back door opener switch and perform automatic open operation.

NOTE:

At this time, automatic operation of back door is performed at half speed.

>> GO TO 4.

4.

STEP 4

1. The back door fully opens.

2. Check that hazard warning lamp blinks and automatic back door warning buzzer sounds normally.
Does hazard warning lamp blink and automatic back door warning buzzer sound normally?

YES

>> GO TO 5.

NO

>> GO TO 1.

5.

STEP 5

Fully close the back door.

>> Inspection End.

2015 Rogue NAM

U1000 CAN COMM CIRCUIT

DLK-111

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

DTC/CIRCUIT DIAGNOSIS

U1000 CAN COMM CIRCUIT

Description

INFOID:0000000011377355

Refer to 

LAN-8, "System Description"

.

DTC Logic

INFOID:0000000011377356

DTC DETECTION LOGIC

NOTE:

U1000 can be set if a module harness was disconnected and reconnected, perhaps during a repair. Confirm

that there are actual CAN diagnostic symptoms and a present DTC by performing the Self Diagnostic Result

procedure.

Diagnosis Procedure

INFOID:0000000011377357

1.

 PERFORM SELF DIAGNOSTIC

1. Turn ignition switch ON and wait for 2 second or more.

2. Check “Self Diagnostic Result”.
Is “CAN COMM CIRCUIT” displayed?

YES

>> Perform CAN Diagnosis as described in DIAGNOSIS section of CONSULT Operation Manual.

NO

>> Refer to 

GI-44, "Intermittent Incident"

.

CONSULT Display

DTC Detection Condition

Possible cause

CAN COMM CIRCUIT
[U1000]

When any listed module cannot communicate with CAN 
communication signal continuously for 2 seconds or 
more with ignition switch ON.

In CAN communication system, any item (or items) 
of the following listed below is malfunctioning:
• Transmission
• Receiving (ECM)
• Receiving (VDC/TCS/ABS)
• Receiving (METER/M&A)
• Receiving (TCM)
• Receiving (IPDM E/R)

2015 Rogue NAM

DLK-112

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

U1010 CONTROL UNIT (CAN)

U1010 CONTROL UNIT (CAN)

DTC Logic

INFOID:0000000011377358

DTC DETECTION LOGIC

Diagnosis Procedure

INFOID:0000000011377359

1.

 REPLACE BCM

When DTC U1010 is detected, replace BCM.

>> Replace BCM. Refer to 

BCS-75, "Removal and Installation"

.

CONSULT Display

DTC Detection Condition

Possible Cause

CAN COMM CIRCUIT
[U1010]

BCM detected internal CAN communication circuit mal-
function.

BCM

2015 Rogue NAM

B2401 IGNITION POWER SUPPLY CIRCUIT

DLK-113

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

B2401 IGNITION POWER SUPPLY CIRCUIT

DTC Logic

INFOID:0000000011278823

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON.

2. Operate automatic back door.

3. Check “Self Diagnostic Result” of “AUTO BACK DOOR” using CONSULT.
Is DTC detected?

YES

>> Refer to 

DLK-113, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000011278824

1.

CHECK BCM OUTPUT SIGNAL

1. Select “IPDM E/R” using CONSULT.

2. Select “PUSH SW” in “Data Monitor”.

3. Check that the function operates normally according to the following conditions:

Is the inspection result normal?

YES

>> Replace automatic back door control module. Refer to 

DLK-283, "Removal and Installation"

.

NO

>> Replace BCM. Refer to 

BCS-75, "Removal and Installation"

.

DTC

CONSULT display 

description

DTC detecting condition

Possible cause

B2401

IGN OPEN

Automatic back door control module cannot detect 
ignition switch ON signal via CAN communication 
with BCM.

• BCM
• Automatic back door control mod-

ule

• CAN communication system

Monitor item

Condition

Status

PUSH SW

Ignition switch

Pressed

Close

Not pressed

Open

2015 Rogue NAM