Nissan Rogue. Manual - part 316

DLK-106

< BASIC INSPECTION >

[WITH INTELLIGENT KEY SYSTEM]

DIAGNOSIS AND REPAIR WORK FLOW

Inspect according to Diagnosis Procedure of the system.
Is malfunctioning part detected?

YES

>> GO TO 8.

NO

>> Check according to 

GI-44, "Intermittent Incident"

.

8.

REPAIR OR REPLACE THE MALFUNCTIONING PART

1. Repair or replace the malfunctioning part.

2. Reconnect parts or connectors disconnected during Diagnosis Procedure again after repair and replace-

ment.

3. Check DTC. If DTC is detected, erase it.

>> GO TO 9.

9.

FINAL CHECK

When DTC is detected in step 2, perform DTC CONFIRMATION PROCEDURE again, and then check that the

malfunction is repaired securely.

When symptom is described by the customer, refer to confirmed symptom in step 3 or 4, and check that the

symptom is not detected.
Is DTC detected and does symptom remain?

YES-1 >> DTC is detected: GO TO 7.

YES-2 >> Symptom remains: GO TO 4.

NO

>> Before returning the vehicle to the customer, always erase DTC.

2015 Rogue NAM

ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL

DLK-107

< BASIC INSPECTION >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMI-
NAL

Description

INFOID:0000000011278809

When the battery is disconnected from the negative terminal, it is necessary to perform initial setting to oper-

ate automatic back door control system normally.

NOTE:

The following specified operations are not performed under the non-initialized condition.

• Automatic back door open/close function

• Anti-pinch function

Work Procedure

INFOID:0000000011278810

1.

INITIALIZATION

1. Fully close the back door manually. (When back door is already fully closed, this operation is not neces-

sary).

2. Perform automatic back door open/close operation of back door.

3. Check for noise or malfunctioning during operation.

4. Check that hazard lamp blinks and that warning buzzer operates.

NOTE:

Never touch back door or allow foreign materials to be pinched in door when performing automatic back door

open/close operation of back door until it is in the fully closed or fully open position.

>> Inspection End.

2015 Rogue NAM

DLK-108

< BASIC INSPECTION >

[WITH INTELLIGENT KEY SYSTEM]

ADDITIONAL SERVICE WHEN REPLACING BCM

ADDITIONAL SERVICE WHEN REPLACING BCM

Description

INFOID:0000000011278811

Perform the system initialization when replacing BCM, replacing Intelligent Key or registering an additional

Intelligent Key.

Work Procedure

INFOID:0000000011278812

Refer to the CONSULT Immobilizer mode and follow the on-screen instructions.

2015 Rogue NAM

ADDITIONAL SERVICE WHEN REPLACING AUTOMATIC BACK DOOR CON-

TROL UNIT

DLK-109

< BASIC INSPECTION >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

ADDITIONAL SERVICE WHEN REPLACING AUTOMATIC BACK DOOR
CONTROL UNIT

Description

INFOID:0000000011278813

When replacing control module or removing connector terminal, it is necessary to perform initial setting to

operate automatic back door system normally.

NOTE:

The following specified operations are not performed under the non-initialized condition:

• Automatic back door open/close function

• Anti-pinch function

Work Procedure

INFOID:0000000011278814

1.

INITIALIZATION

1. Fully close the back door manually. (When back door is already fully closed, this operation is not neces-

sary.)

2. Perform automatic back door open/close operation of back door.

3. Check for noise or malfunctioning during operation.

4. Check that hazard lamp blinks and that warning buzzer operates.

NOTE:

Never touch back door or allow foreign materials to be pinched in door when performing automatic back door

open/close operation of back door until it is in the fully closed or fully open position.

>> Inspection End.

2015 Rogue NAM