Nissan Rogue. Manual - part 320

DLK-122

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

B2417 TOUCH SENSOR LH

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Replace automatic back door control module. Refer to 

DLK-283, "Removal and Installation"

.

7.

CHECK TOUCH SENSOR LH

Refer to 

DLK-119, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 8.

NO

>> Replace touch sensor LH. Refer to 

DLK-271, "TOUCH SENSOR : Removal and Installation"

8.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-44, "Intermittent Incident"

.

>> Inspection End.

Component Inspection

INFOID:0000000011278833

1.

CHECK TOUCH SENSOR LH

1. Turn ignition switch OFF.

2. Disconnect touch sensor LH connector.

3. Check resistance between touch sensor LH terminals.

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Replace touch sensor LH. Refer to 

DLK-271, "TOUCH SENSOR : Removal and Installation"

.

(+)

(–)

Voltage

(Approx.)

Automatic back door control module

 Connector

Terminal

B55

13

Ground

0.01 – 0 V

Touch sensor LH

 Condition

Resistance 

(Approx.)

Terminal

1

2

Touch sensor LH

Detect obstruction

380 – 420 k

Ω

Other than above

0.95 – 1.05 k

Ω

2015 Rogue NAM

B2419 OPEN SWITCH

DLK-123

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

B2419 OPEN SWITCH

DTC Logic

INFOID:0000000011278834

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON. 

2. Operate automatic back door.

3. Check “Self Diagnostic Result” of “AUTO BACK DOOR” using CONSULT.
Is DTC detected?

YES

>> Refer to 

DLK-123, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000011278835

Regarding Wiring Diagram information, refer to 

DLK-90, "Wiring Diagram"

.

1.

CHECK FOR FOREIGN MATERIALS IN BACK DOOR LOCK ASSEMBLY

Check for entry of foreign materials in back door lock assembly.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Remove foreign materials.

2.

CHECK BACK DOOR OPEN/CLOSE OPERATION

Manually check open and close operation of back door.
Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the malfunctioning parts.

3.

CHECK OPEN SWITCH SIGNAL

1. Select “AUTO BACK DOOR” using CONSULT.

2. Select “OPEN SW” in “Data Monitor”.

3. Check that the function operates normally according to the following conditions:

Is the inspection result normal?

YES

>> GO TO 8.

NO

>> GO TO 4.

4.

CHECK OPEN SWITCH INPUT SIGNAL

DTC

CONSULT display 

description

DTC detecting condition

Possible cause

B2419

OPEN SW

Automatic back door control module detects a mal-
function of open switch during automatic operation 
of back door.

• Entry of foreign materials to back 

door lock assembly

• Back door mechanism
• Automatic back door control mod-

ule

• Open switch
• Harness or connectors

Monitor item

Condition

Status

OPEN SW

Back door

Fully closed/Half latch

OFF

Open

ON

2015 Rogue NAM

DLK-124

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

B2419 OPEN SWITCH

1. Turn ignition switch OFF.

2. Disconnect back door lock assembly connector.

3. Check voltage between back door lock assembly harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> GO TO 5.

5.

CHECK OPEN SWITCH CIRCUIT

1. Disconnect automatic back door control module connector.

2. Check continuity between automatic back door control module harness connector and back door lock

assembly harness connector.

3. Check continuity between automatic back door control module harness connector and ground.

Is the inspection result normal?

YES

>> Replace automatic back door control module. Refer to 

DLK-283, "Removal and Installation"

.

NO

>> Repair or replace harness.

6.

CHECK OPEN SWITCH GROUND CIRCUIT

Check continuity between back door lock assembly harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Repair or replace harness.

7.

CHECK OPEN SWITCH

Refer to 

DLK-115, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 8.

NO

>> Replace back door lock assembly. Refer to 

DLK-270, "DOOR LOCK : Removal and Installation"

.

8.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-44, "Intermittent Incident"

.

>> Inspection End.

Component Inspection

INFOID:0000000011278836

COMPONENT INSPECTION

(+)

(–)

Voltage

(Approx.)

Back door lock assembly

Connector

Terminal

D512

4

Ground

Battery voltage

Automatic back door control module

Back door lock assembly

Continuity 

 Connector

Terminal

 Connector

Terminal

B55

11

D512

4

Yes

Automatic back door control module

Ground

Continuity 

 Connector

Terminal

B55

11

No

Back door lock assembly

Ground

Continuity 

 Connector

Terminal

D512

8

Yes

2015 Rogue NAM

B2419 OPEN SWITCH

DLK-125

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

1.

CHECK SWITCH

1. Turn ignition switch OFF.

2. Disconnect back door lock assembly connector.

3. Check continuity between back door lock assembly terminals.

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Replace back door lock assembly. Refer to 

DLK-270, "DOOR LOCK : Removal and Installation"

.

Back door lock assembly

Condition

Continuity

Terminal

4

8

Back door lock

Open

Yes

Fully closed/Half latch

No

5

Fully close

Yes

Open/Half latch

No

6

Open

Yes

Fully closed/Half latch

No

7

Back door 
switch

On

Yes

Off

No

2015 Rogue NAM