Nissan Rogue. Manual - part 1101

B27D1 START CUT RELAY OFF

SEC-183

< DTC/CIRCUIT DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

B27D1 START CUT RELAY OFF

DTC Logic

INFOID:0000000011278598

DTC DETECTION LOGIC

NOTE:

• If DTC B27D1 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to

BCS-124, "DTC Logic"

.

• If DTC B27D1 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to

BCS-125, "DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch under the following conditions to start engine, and wait 1 second or more.

-

Selector lever: In the P position

2. Check DTC in “Self Diagnostic Result” of “BCM” using CONSULT.
Is DTC detected?

YES

>> Go to 

SEC-183, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000011278599

Regarding Wiring Diagram information, refer to 

SEC-133, "Wiring Diagram"

.

1.

CHECK STARTER CUT RELAY POWER SUPPLY CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect starter cut relay.

3. Check voltage between starter cut relay harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO-1 >> Check 30 A fusible link [M, located in the fuse block (J/B)].

NO-2 >> Check harness for open or short between starter cut relay and fusible link.

2.

CHECK STARTER CUT RELAY CONTROL 

1. Reconnect starter cut relay.

2. Check voltage between BCM harness connector and ground.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B27D1

STARTER CUT RELAY 
OFF

When comparing the starter cut relay signal 
(CAN) from IPDM E/R, BCM detects that starter 
cut relay is stuck in the OFF position for 1 sec-
ond or more.

• Harness or connectors

(The CAN communication line is open 
or shorted.)

• Harness or connector

(Starter cut relay circuit is open or short-
ed.)

• IPDM E/R
• BCM
• Starter cut relay

(+)

(–)

Voltage (V)

(Approx.)

Starter cut relay

Connector

Terminal

F55

1

Ground

Battery voltage

3

2015 Rogue NAM

SEC-184

< DTC/CIRCUIT DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

B27D1 START CUT RELAY OFF

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> GO TO 3.

3.

CHECK STARTER CUT RELAY CONTROL CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect BCM connector.

3. Disconnect starter cut relay.

4. Check continuity between BCM harness connector and starter cut relay harness connector.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK STARTER CUT RELAY CIRCUIT 

1. Turn ignition switch OFF.

2. Disconnect IPDM E/R connector.

3. Check continuity between IPDM E/R harness connector and starter cut relay harness connector.

4. Check continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace harness.

5.

CHECK STARTER CUT RELAY

Refer to 

SEC-185, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Replace starter cut relay.

6.

REPLACE BCM

1. Replace BCM. Refer to 

BCS-135, "Removal and Installation"

.

2. Perform initialization of BCM and registration of all keys using CONSULT.

3. Perform DTC CONFIRMATION PROCEDURE for DTC B27D1. Refer to 

SEC-183, "DTC Logic"

.

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Replace IPDM E/R. Refer to 

PCS-40, "Removal and Installation"

.

(+)

(–)

Condition

Voltage (V)

(Approx.)

BCM

Connector

Terminal

E29

139

Ground

CVT shift selector lever

N or P position

Battery voltage

Other than above

0

BCM

Starter cut relay

Continuity

Connector

Terminal

Connector

Terminal

E29

139

F55

2

Yes

IPDM E/R

Starter cut relay

Continuity

Connector

Terminal

Connector

Terminal

F41

86

F55

5

Yes

IPDM E/R

Ground

Continuity

Connector

Terminal

F41

86

No

2015 Rogue NAM

B27D1 START CUT RELAY OFF

SEC-185

< DTC/CIRCUIT DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

Component Inspection

INFOID:0000000011278600

1.

CHECK STARTER CUT RELAY

1. Turn ignition switch OFF.

2. Disconnect starter cut relay.

3. Check continuity between starter cut relay terminals.

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Replace starter cut relay.

Starter cut relay

Condition

Continuity

Terminal

3

5

12 V direct current supply between terminals 1 and 2

Yes

No current supply

No

2015 Rogue NAM

SEC-186

< DTC/CIRCUIT DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

B27D2 START CUT RELAY ON

B27D2 START CUT RELAY ON

DTC Logic

INFOID:0000000011278601

DTC DETECTION LOGIC

NOTE:

• If DTC B27D2 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to

BCS-124, "DTC Logic"

.

• If DTC B27D2 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to

BCS-125, "DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch under the following conditions to start engine, and wait 1 second or more.

-

Selector lever: In the P position

2. Check DTC in “Self Diagnostic Result” of “BCM” using CONSULT.
Is DTC detected?

YES

>> Go to 

SEC-186, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000011278602

Regarding Wiring Diagram information, refer to 

SEC-133, "Wiring Diagram"

.

1.

CHECK STARTER CUT RELAY POWER SUPPLY CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect starter cut relay.

3. Check voltage between starter cut relay harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO-1 >> Check 30 A fusible link [M, located in the fuse block (J/B)].

NO-2 >> Check harness for open or short between starter cut relay and fusible link.

2.

CHECK STARTER CUT RELAY CONTROL 

1. Reconnect starter cut relay.

2. Check voltage between BCM harness connector and ground.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B27D2

STARTER CUT RELAY 
ON

When comparing the starter cut relay signal 
(CAN) from IPDM E/R, BCM detects that starter 
cut relay is stuck in the ON position for 1 second 
or more.

• Harness or connectors

(The CAN communication line is open 
or shorted.)

• Harness or connector

(Starter cut relay circuit is open or short-
ed.)

• IPDM E/R
• BCM
• Starter cut relay

(+)

(–)

Voltage (V)

(Approx.)

Starter cut relay

Connector

Terminal

F55

1

Ground

Battery voltage

3

2015 Rogue NAM