Nissan Rogue. Manual - part 1011

RF-24

< BASIC INSPECTION >

DIAGNOSIS AND REPAIR WORKFLOW

>> GO TO 2.

2.

 CONFIRM CONCERN

Check the malfunction on the vehicle that the customer describes.

Inspect the relation of the symptoms and the condition when the symptoms occur.

>> GO TO 3.

3.

 IDENTIFY THE MALFUNCTIONING SYSTEM WITH SYMPTOM DIAGNOSIS

Use Symptom diagnosis from the symptom inspection result in step 2 and then identify where to start perform-

ing the diagnosis based on possible causes and symptoms.

>> GO TO 4.

4.

 PERFORM THE COMPONENT DIAGNOSIS OF THE APPLICABLE SYSTEM

Perform the diagnosis with Component diagnosis of the applicable system.

>> GO TO 5.

5.

 REPAIR OR REPLACE THE MALFUNCTIONING PARTS

Repair or replace the specified malfunctioning parts.

>> GO TO 6.

6.

 FINAL CHECK

Check that malfunctions are not reproduced when obtaining the malfunction information from the customer,

referring to the symptom inspection result in step 2.
Are the malfunctions corrected?

YES

>> Inspection End.

NO

>> GO TO 3.

INSPECTION AND ADJUSTMENT

RF-25

< BASIC INSPECTION >

C

D

E

F

G

H

I

J

L

M

A

B

RF

N

O

P

INSPECTION AND ADJUSTMENT

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Re-
quirement

INFOID:0000000011280132

INITIALIZATION PROCEDURE 

Moonroof 

If the moonroof does not open or close automatically, use the following procedure to return moonroof opera-

tion to normal:

1. Turn ignition switch ON.

2. Push and hold the moonroof switch forward until the moonroof and sunshade stop and bounce back. 

3. Release the moonroof switch.

4. Press and hold the moonroof switch within 6 seconds. 

5. The roof glass and shade will move to full open and back to full close. 

6. Release the switch, initialization is complete if the moonroof operates normally.

ANTI-PINCH FUNCTION

Moonroof/Sunshade

1. Fully open the moonroof to the full open position.

2. Place a piece of wood at the fully closed position.

3. Close the moonroof completely with auto-slide close function. 

4. Moonroof should make contact and then tilt up or travel in reverse. 

CAUTION:

• Do not test the anti-pinch function with your hands or other body parts because they may be

pinched. 

• Depending on the environment and driving conditions, if a similar impact or load is applied to the

moonroof it may lower.

• Test the auto-slide operation before inspection when the initialization procedure is performed.

• Perform the initialization procedure when the auto-slide operation or anti-pinch function does not

operate normally.

RF-26

< DTC/CIRCUIT DIAGNOSIS >

POWER SUPPLY AND GROUND CIRCUIT

DTC/CIRCUIT DIAGNOSIS

POWER SUPPLY AND GROUND CIRCUIT

BCM (BODY CONTROL SYSTEM) (WITH INTELLIGENT KEY SYSTEM)
BCM (BODY CONTROL SYSTEM) (WITH INTELLIGENT KEY SYSTEM) : Diagnosis 
Procedure

INFOID:0000000011382158

Regarding Wiring Diagram information, refer to 

BCS-50, "Wiring Diagram"

.

1.

 CHECK FUSE

Check that the following fuse is not blown.

Is the fuse blown?

YES

>> Replace the blown fuse after repairing the affected circuit.

NO

>> GO TO 2.

2.

 CHECK POWER SUPPLY CIRCUIT

1. Disconnect BCM connector M20.

2. Check voltage between BCM connector M20 and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness or connectors.

3.

 CHECK GROUND CIRCUIT

Check continuity between BCM connector M20 and ground.

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Repair or replace harness or connectors.

BCM (BODY CONTROL SYSTEM) (WITHOUT INTELLIGENT KEY SYSTEM)
BCM (BODY CONTROL SYSTEM) (WITHOUT INTELLIGENT KEY SYSTEM) : Diag-
nosis Procedure

INFOID:0000000011382159

Regarding Wiring Diagram information, refer to 

BCS-110, "Wiring Diagram"

.

1.

 CHECK FUSE

Terminal No.

Signal name

Fuse No.

161

BCM power supply

7 (10A)

BCM

Ground

Voltage

(Approx.)

Connector

Terminal

M20

161

—

Battery voltage

BCM

Ground

Continuity

Connector

Terminal

M20

170

—

Yes

171

POWER SUPPLY AND GROUND CIRCUIT

RF-27

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

RF

N

O

P

Check that the following fuse is not blown.

Is the fuse blown?

YES

>> Replace the blown fuse after repairing the affected circuit.

NO

>> GO TO 2.

2.

 CHECK POWER SUPPLY CIRCUIT

1. Disconnect BCM connector M20.

2. Check voltage between BCM connector M20 and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness or connectors.

3.

 CHECK GROUND CIRCUIT

Check continuity between BCM connector M20 and ground.

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Repair or replace harness or connectors.

MOONROOF MOTOR ASSEMBLY
MOONROOF MOTOR ASSEMBLY : Description

INFOID:0000000011280135

• BCM supplies the moonroof motor assembly with power.

• CPU is integrated in moonroof motor assembly.

• Tilts up/down & slides open/close by moonroof switch operation.

• In order to close the moonroof during high speed driving, the Combination meter will send a speed signal to

the moonroof CPU to adjust the torque of the motor during the tilt-down operation. 

MOONROOF MOTOR ASSEMBLY : Component Function Check

INFOID:0000000011280136

1.

 CHECK MOONROOF MOTOR FUNCTION

Does the tilt up/down & slide open/close functions operate normally with moonroof switch?
Is the inspection result normal?

YES

>> Moonroof motor assembly is OK.

NO

>> Refer to 

RF-27, "MOONROOF MOTOR ASSEMBLY : Diagnosis Procedure"

. 

MOONROOF MOTOR ASSEMBLY : Diagnosis Procedure

INFOID:0000000011280137

Regarding Wiring Diagram information, refer to 

RF-17, "Wiring Diagram"

.

Terminal No.

Signal name

Fuse No.

161

BCM power supply

7 (10A)

BCM

Ground

Voltage

(Approx.)

Connector

Terminal

M20

161

—

Battery voltage

BCM

Ground

Continuity

Connector

Terminal

M20

170

—

Yes

171