Nissan Maxima. Manual - part 260

 

  Index      Nissan     Nissan Maxima (2009-2014 year) - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  258  259  260  261   ..

 

 

Nissan Maxima. Manual - part 260

 

 

C1147, C1148, C1149, C1150 USV/HSV LINE

BRC-61

< DTC/CIRCUIT DIAGNOSIS >

[VDC/TCS/ABS]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

*: On for 1 to 2 seconds after the touch, and then Off

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Go to diagnosis procedure. Refer to 

BRC-59, "Diagnosis Procedure"

.

Special Repair Requirement

INFOID:0000000010049106

1.

ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION

Always perform the neutral position adjustment for the steering angle sensor, when replacing the ABS actua-

tor and electric unit (control unit). Refer to 

BRC-6, "ADJUSTMENT OF STEERING ANGLE SENSOR NEU-

TRAL POSITION : Special Repair Requirement"

.

>> END

RR RH ABS SOLENOID (ACT)

RR RH IN SOL

Off

Off

Off

RR RH OUT SOL

Off

Off

Off

USV[FL-RR]

Off

Off

Off

USV[FR-RL]

Off

On

On

HSV[FL-RR]

Off

Off

Off

HSV[FR-RL]

Off

On*

Off

RR LH ABS SOLENOID (ACT)

RR LH IN SOL

Off

Off

Off

RR LH OUT SOL

Off

Off

Off

USV[FL-RR]

Off

Off

Off

USV[FR-RL]

Off

On

On

HSV[FL-RR]

Off

Off

Off

HSV[FR-RL]

Off

On*

Off

Operation

ABS solenoid valve (ACT)

Up

ACT UP

ACT KEEP

BRC-62

< DTC/CIRCUIT DIAGNOSIS >

[VDC/TCS/ABS]

C1154 PNP SWITCH

C1154 PNP SWITCH

Description

INFOID:0000000010049107

The transmission range switch signal is transmitted to the ABS actuator and electric unit (control unit) using

the CAN communication lines. 

DTC Logic

INFOID:0000000010049108

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAGNOSIS RESULTS

Check the self-diagnosis results.

Is above displayed on the self-diagnosis display?

YES

>> Proceed to diagnosis procedure. Refer to 

BRC-62, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000010049109

1.

CHECK DATA MONITOR

Select  “SLCT LVR POSI” in “Data Monitor” and check transmission range switch signal.

Is the inspection result normal?

YES

>> Replace ABS actuator and electric unit (control unit). Refer to 

BRC-106, "Removal and Installa-

tion"

.

NO

>> GO TO 2

2.

CHECK TRANSMISSION RANGE SWITCH

Perform transmission range switch inspection. Refer to 

TM-51, "Component Inspection (Transmisson Range

Switch)"

.

Is the inspection result normal?

YES

>> Replace ABS actuator and electric unit (control unit). Refer to 

BRC-106, "Removal and Installa-

tion"

.

NO

>> Repair or replace malfunctioning components.

Special Repair Requirement

INFOID:0000000010049110

1.

ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION

DTC

Display item

Malfunction detected condition

Possible cause

C1154

PNP POS SIG

Transmission range switch signal or communication line 
between the ABS actuator and electric unit (control unit) 
and TCM is open or shorted.

• Harness or connector
• Transmission range switch

Self-diagnosis results

PNP POS SIG

Selector lever position

SLCT LVR POSI (Data monitor)

P position

P

R position

R

N position

N

D position

D

C1154 PNP SWITCH

BRC-63

< DTC/CIRCUIT DIAGNOSIS >

[VDC/TCS/ABS]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

Always perform the neutral position adjustment for the steering angle sensor, when replacing the ABS actua-

tor and electric unit (control unit). Refer to 

BRC-6, "ADJUSTMENT OF STEERING ANGLE SENSOR NEU-

TRAL POSITION : Special Repair Requirement"

.

>> END

BRC-64

< DTC/CIRCUIT DIAGNOSIS >

[VDC/TCS/ABS]

C1155 BR FLUID LEVEL LOW

C1155 BR FLUID LEVEL LOW

Description

INFOID:0000000010049111

The brake fluid level switch converts the brake fluid level to an electric signal and transmits it to the ABS actu-

ator and electric unit (control unit). 

DTC Logic

INFOID:0000000010049112

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAGNOSIS RESULTS

Check the self-diagnosis results.

Is above displayed on the self-diagnosis display?

YES

>> Proceed to diagnosis procedure. Refer to 

BRC-64, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000010049113

Regarding Wiring Diagram information, refer to 

BRC-83, "Wiring Diagram"

.

CAUTION:

Check brake fluid level in brake reservoir tank before starting inspection.

1.

CONNECTOR INSPECTION

1. Turn ignition switch OFF.

2. Disconnect brake fluid level switch connector and combination meter connector.

3. Check terminals for deformation, disconnection, looseness, and so on. If any malfunction is found, repair

or replace terminals.

4. Reconnect connector and perform self-diagnosis. Refer to 

BRC-21, "CONSULT Function (ABS)"

.

Is any item displayed on the self-diagnosis display?

YES

>> GO TO 2

NO

>> Poor connection of connector terminals. Repair or replace connectors.

2.

CHECK BRAKE FLUID LEVEL SWITCH 

Perform the brake fluid level switch component inspection. Refer to 

BRC-65, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 3

NO

>> Replace brake fluid level switch. Refer to 

BR-24, "Exploded View"

.

3.

CHECK BRAKE FLUID LEVEL SWITCH HARNESS

DTC

Display item

Malfunction detected condition

Possible cause

C1155

BR FLUID LEVEL LOW

Brake fluid level is low or communication line between 
the ABS actuator and electric unit (control unit) and brake 
fluid level switch is open or shorted.

• Harness or connector
• Brake fluid level switch

Self-diagnosis results

BR FLUID LEVEL LOW

 

 

 

 

 

 

 

Content   ..  258  259  260  261   ..