Nissan Altima HL32 Hybrid. Manual - part 749

PRECAUTIONS

INL-87

< PRECAUTION >

C

D

E

F

G

H

I

J

K

M

A

B

INL

N

O

P

• After re-assembly has been completed, make sure each part functions correctly.

• Never work with wet hands.

• Turn the lighting switch OFF before disconnecting and connecting the connector.

• Do not use organic solvent (paint thinner or gasoline) to clean lamps or remove sealant residue.

INL-88

< ON-VEHICLE REPAIR >

INTERIOR ROOM LAMP

ON-VEHICLE REPAIR

INTERIOR ROOM LAMP

Removal and Installation

INFOID:0000000004216497

FRONT ROOM/MAP LAMP

NOTE:

For non-sunroof equipped vehicles, the front room/map lamp assembly is part of the headlining and replaced

only as an assembly. Refer to 

INT-23, "Removal and Installation"

.

Removal

1. Disconnect the negative 12-volt battery terminal.
2. Release the metal clips and drop front edge of front room/map

lamp (1) away from headlining. Slide front room/map lamp for-

ward in vehicle to clear pawls at rear.

: Vehicle front

: Metal clip
: Pawl

3. Disconnect the connectors, then remove front room/map lamp.

Installation

Installation is in the reverse order of removal.

Bulb Replacement

1. Remove the front room/map lamp lens (2), using a suitable tool

(A).

2. Pull bulb (1) straight out to remove.

VANITY MIRROR LAMP

Removal

The vanity mirror lamp is replaced as part of the sunvisor assembly. Refer to 

INT-23, "Exploded View"

.

Installation

Installation is in the reverse order of removal.

Bulb Replacement

1. Remove the vanity mirror lamp lens (2), using a suitable tool (A).
2. Pull bulb (3) straight out to remove.

ALLIA0009ZZ

Front room/map lamp bulb

: 12V - 8W

AWLIA1696ZZ

AWLIA1697ZZ

INTERIOR ROOM LAMP

INL-89

< ON-VEHICLE REPAIR >

C

D

E

F

G

H

I

J

K

M

A

B

INL

N

O

P

GLOVE BOX LAMP

Removal

1. Disconnect the negative 12-volt battery terminal.
2. Remove the lower instrument glove box assembly (1). Refer to

IP-11, "Exploded View"

.

3. Rotate glove box lamp socket (3) counterclockwise to remove,

then remove the glove box lamp bulb (2).

Installation

Installation is in the reverse order of removal.

Bulb Replacement

1. Remove glove box lamp socket.
2. Pull bulb straight out to remove.

STEP LAMP

Removal

1. Disconnect the negative 12-volt battery terminal.
2. Insert a suitable tool between door finisher and step lamp lens/socket to release the pawls.
3. Disconnect the step lamp connector, then remove step lamp lens and socket.

Installation

Installation is in the reverse order of removal.

Bulb Replacement

1. Remove the step lamp lens/socket.
2. Pull the bulb straight out to remove.

PERSONAL LAMP

Removal

ALLIA0012ZZ

ALLIA0013ZZ

1.

Step lamp connector

2.

Door finisher

3.

Step lamp lens/socket

4.

Step lamp bulb

Vehicle front

INL-90

< ON-VEHICLE REPAIR >

INTERIOR ROOM LAMP

The personal lamp LH/RH is replaced as part of the headlining assembly. Refer to 

INT-23, "Removal and

Installation"

.

Installation

Installation is in the reverse order of removal.

Bulb Replacement

1. Release the pawls and remove personal lamp lens (3) from the

personal lamp housing(1), using a suitable tool.

⇐: Vehicle front

2. Pull bulb (2) straight out to remove.

Personal lamp bulb

: 12V - 8W

AWLIA1698ZZ