Nissan Altima HL32 Hybrid. Manual - part 442

EXL-168

< ON-VEHICLE REPAIR >

LIGHTING AND TURN SIGNAL SWITCH

LIGHTING AND TURN SIGNAL SWITCH

Removal and Installation

INFOID:0000000004216454

Removal

1. Remove the spiral cable. Refer to 

SRS-8, "Removal and Installation"

.

2. Disconnect the lighting and turn signal switch connector and remove the lighting and turn signal switch.

Installation

Installation is in the reverse order of removal.

HAZARD SWITCH

EXL-169

< ON-VEHICLE REPAIR >

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

HAZARD SWITCH

Removal and Installation

INFOID:0000000004216455

Removal

1. Remove the center ventilator grilles. Refer to 

VTL-24, "CENTER VENTILATOR GRILLES : Removal and

Installation"

.

2. Remove the hazard switch screws (A) and remove the hazard

switch (1). 

Installation

Installation is in the reverse order of removal.

ALLIA0037ZZ

EXL-170

< SERVICE DATA AND SPECIFICATIONS (SDS) 

SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS)

Headlamp

INFOID:0000000004216456

*: Always check with the Parts Department for the latest parts information.

Exterior Lamp

INFOID:0000000004216457

*: Always check with the Parts Department for the latest parts information.

Item

Wattage (W)*

Low 

55 (H1)

High

60 (HB3)

Item

Wattage (W)*

Front combination lamp

Turn signal lamp

27 (amber)

Park/side marker lamp

8

Rear combination lamp

Stop/Tail lamp

27/8

Turn signal lamp

27

Back-up lamp

13

Side marker lamp

5

Fog lamp

55 (H11)

License plate lamp

5

High-mounted stop lamp (parcel shelf mount)

18

High-mounted stop lamp (rear air spoiler mount)

LED

EXT-1

BODY EXTERIOR, DOORS, ROOF & VEHICLE SECURITY

C

D

E

F

G

H

I

J

L

M

SECTION 

EXT

A

B

EXT

N

O

P

CONTENTS

EXTERIOR

PRECAUTION ...............................................

2

PRECAUTIONS ...................................................

2

Precaution for Supplemental Restraint System 
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ...................................................................

2

Precaution for Procedure without Cowl Top Cover 

......

2

Precaution .................................................................

2

PREPARATION ............................................

3

PREPARATION ...................................................

3

Special Service Tool  .................................................

3

Commercial Service Tool  ..........................................

3

ON-VEHICLE MAINTENANCE .....................

4

SQUEAK AND RATTLE TROUBLE DIAG-
NOSES ................................................................

4

Work Flow  .................................................................

4

Generic Squeak and Rattle Troubleshooting  ............

6

Diagnostic Worksheet  ...............................................

8

Clip and Fastener ......................................................

9

ON-VEHICLE REPAIR .................................

12

FRONT BUMPER  ...............................................

12

Removal and Installation .........................................

12

REAR BUMPER  .................................................

14

Removal and Installation  .........................................

14

FRONT GRILLE  ................................................

16

Removal and Installation  .........................................

16

COWL TOP  .......................................................

17

Removal and Installation  .........................................

17

FENDER PROTECTOR  ....................................

18

Removal and Installation  .........................................

18

MUDGUARD .....................................................

19

Removal and Installation  .........................................

19

SIDE GUARD MOLDING ..................................

20

Removal and Installation  .........................................

20

DOOR OUTSIDE MOLDING  .............................

21

Removal and Installation  .........................................

21

DRIP MOLDING  ................................................

22

Removal and Installation  .........................................

22

ROOF SIDE MOLDING  .....................................

23

Removal and Installation  .........................................

23

LICENSE LAMP FINISHER  ..............................

24

Removal and Installation  .........................................

24

REAR SPOILER ................................................

25

Removal and Installation  .........................................

25