Nissan Frontier. Manual - part 599

PRECAUTIONS

EC-967

< PRECAUTION >

[VQ40DE FOR MEXICO]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

• B1 indicates the bank 1, B2 indicates the bank 2 as shown in

the figure.

• Never operate fuel pump when there is no fuel in lines.

• Tighten fuel hose clamps to the specified torque.

• Never depress accelerator pedal when starting.

• Immediately after starting, never rev up engine unnecessarily.

• Never rev up engine just prior to shutdown.

• When installing C.B. ham radio or a mobile phone, always

observe the following as it may adversely affect electronic

control systems depending on installation location.

- Keep the antenna as far as possible from the electronic con-

trol units.

- Keep the antenna feeder line more than 20 cm (8 in) away

from the harness of electronic controls.

Never let them run parallel for a long distance.

- Adjust the antenna and feeder line so that the standing-wave

radio can be kept smaller.

SEC893C

BBIA0529E

SEF709Y

SEF708Y

EC-968

< PRECAUTION >

[VQ40DE FOR MEXICO]

PRECAUTIONS

- Always ground the radio to vehicle body.

PBIB1512E

PREPARATION

EC-969

< PREPARATION >

[VQ40DE FOR MEXICO]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

PREPARATION

PREPARATION

Special Service Tool

INFOID:0000000009481676

The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.

Tool number
(Kent-Moore No.)
Tool name

Description

EG17650301
(J-33984-A)
Radiator cap tester 
adapter

Adapts radiator cap tester to radiator cap and radi-
ator filler neck
a: 28 (1.10) dia.
b: 31.4 (1.236) dia.
c: 41.3 (1.626) dia.
Unit: mm (in)

(J-44321)
Fuel pressure gauge 
kit

Checks fuel pressure

(J-44321-6)
Fuel pressure adapter

Connects fuel pressure gauge to quick connector 
type fuel lines.

(J-45488)
Quick connector re-
lease

 

Removes fuel tube quick connectors in engine 
room

S-NT564

LEC642

LBIA0376E

PBIC0198E

EC-970

< PREPARATION >

[VQ40DE FOR MEXICO]

PREPARATION

Commercial Service Tool

INFOID:0000000009481677

Tool name
(Kent-Moore No.)

Description

Leak detector 
i.e.: (J-41416)

Locates the EVAP leak

EVAP service port 
adapter
i.e.: (J-41413-OBD)

Applies positive pressure through EVAP service 
port

Fuel filler cap adapter
i.e.: (MLR-8382)

Checks fuel tank vacuum relief valve opening 
pressure

Socket wrench

Removes and installs engine coolant temperature 
sensor

Oxygen sensor thread 
cleaner
i.e.: (J-43897-18)
(J-43897-12)

Reconditions the exhaust system threads before 
installing a new oxygen sensor. Use with anti-
seize lubricant shown below.
a: 18 mm diameter with pitch 1.5 mm for Zirco-
nia Oxygen Sensor
b: 12 mm diameter with pitch 1.25 mm for Tita-
nia Oxygen Sensor

Anti-seize lubricant 
i.e.: (Permatex

TM

 

133AR or equivalent 
meeting MIL specifica-
tion MIL-A-907)

Lubricates oxygen sensor thread cleaning tool 
when reconditioning exhaust system threads.

S-NT703

S-NT704

S-NT815

S-NT705

AEM488

S-NT779