Nissan Sentra. Manual - part 711

POWER SUPPLY AND GROUND CIRCUIT

PWC-41

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

PWC

N

O

P

3.

 CHECK HARNESS CONTINUITY (REAR POWER WINDOW SWITCH RH)

1. Turn ignition switch OFF.

2. Disconnect main power window and door lock/unlock switch and rear power window switch RH.

3. Check continuity between main power window and door lock/unlock switch connector D5 and rear power

window switch RH connector D303.

4. Check continuity between main power window and door lock/unlock switch connector D5 and ground.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace the harness or connectors.

4.

 CHECK HARNESS CONTINUITY

1. Disconnect BCM, power window and door lock/unlock switch RH, rear power window switch LH and rear

power window switch RH.

2. Check continuity between BCM connector and rear power window switch connector.

With Intelligent Key system

Without Intelligent Key system

3. Check continuity between BCM connector M85 or M20 and ground.

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-73, "Removal and Installation"

 (with Intelligent Key) or 

BCS-126,

"Removal and Installation"

 (without Intelligent Key).

NO

>> Repair or replace harness or connectors.

5.

 CHECK REAR POWER WINDOW SWITCH

Check rear power window switch.

Refer to 

PWC-42, "REAR POWER WINDOW SWITCH : Component Inspection"

.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-39, "Intermittent Incident"

.

NO

>> Replace rear power window switch. Refer to 

PWC-72, "Removal and Installation"

.

Main power window and door lock/

unlock switch connector

Terminal

Rear power window switch 

RH connector

Terminal

Continuity

D5

6

D303

7

Yes

7

4

Main power window and door lock/un-

lock switch connector

Terminal

Ground

Continuity

D5

6

No

7

BCM

connector

Terminal

Rear power window switch connector

Terminal

Continuity

M85

92

LH

D203

6

Yes

RH

D303

BCM

connector

Terminal

Rear power window switch connector

Terminal

Continuity

M20

68

LH

D203

6

Yes

RH

D303

BCM

Ground

Continuity

Connector

Terminal

M85 (with Intelligent Key system)

92

No

M20 (without Intelligent Key system)

68

PWC-42

< DTC/CIRCUIT DIAGNOSIS >

POWER SUPPLY AND GROUND CIRCUIT

REAR POWER WINDOW SWITCH : Component Inspection

INFOID:0000000009757246

COMPONENT INSPECTION

1.

 CHECK REAR POWER WINDOW SWITCH

Check rear power window switch.

Is the inspection result normal?

YES

>> Rear power window switch is OK.

NO

>> Replace rear power window switch. Refer to 

PWC-72, "Removal and Installation"

.

Terminal

Power window switch condition

Continuity

6

5

UP

Yes

8

7

7

8

NEUTRAL

5

4

8

6

DOWN

5

4

POWER WINDOW MOTOR

PWC-43

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

PWC

N

O

P

POWER WINDOW MOTOR

DRIVER SIDE
DRIVER SIDE : Description

INFOID:0000000009757247

Door glass moves UP/DOWN by receiving the signal from main power window and door lock/unlock switch.

DRIVER SIDE : Component Function Check

INFOID:0000000009757248

1.

 CHECK FRONT POWER WINDOW MOTOR LH CIRCUIT

Check front power window motor LH operation with the main power window and door lock/unlock switch.
Is the inspection result normal?

YES

>> Front power window motor LH is OK.

NO

>> Refer to 

PWC-43, "DRIVER SIDE : Diagnosis Procedure"

.

DRIVER SIDE : Diagnosis Procedure

INFOID:0000000009757249

Regarding Wiring Diagram information, refer to 

PWC-18, "Wiring Diagram"

.

Front Power Window Motor LH Circuit Check

1.

 CHECK MAIN POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH OUTPUT SIGNAL

1. Turn ignition switch OFF.

2. Disconnect front power window motor LH.

3. Turn ignition switch ON.

4. Check voltage between front power window motor LH connector D8 and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

 CHECK HARNESS CONTINUITY

1. Turn ignition switch OFF.

2. Disconnect main power window and door lock/unlock switch.

3. Check continuity between main power window and door lock/unlock switch connector D11 and front

power window motor LH connector D8.

4. Check continuity between main power window and door lock/unlock switch connector D11 and ground.

Terminal

Main power window and 

door lock/unlock switch con-

dition

Voltage

(Approx.)

(+)

(–)

Front power window motor 

LH connector

Terminal

D8

1

Ground

UP

Battery voltage

DOWN

0

3

UP

0

DOWN

Battery voltage

Main power window and door lock/un-

lock switch 

connector

Terminal

Front power window motor LH 

connector

Terminal

Continuity

D11

17

D8

1

Yes

19

3

PWC-44

< DTC/CIRCUIT DIAGNOSIS >

POWER WINDOW MOTOR

Is the inspection result normal?

YES

>> Replace main power window and door lock/unlock switch. Refer to 

PWC-70, "Removal and Instal-

lation"

. After that, refer to 

PWC-29, "Work Procedure"

.

NO

>> Repair or replace harness.

3.

 CHECK FRONT POWER WINDOW MOTOR LH

Check front power window motor LH.

Refer to 

PWC-44, "DRIVER SIDE : Component Inspection"

.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-39, "Intermittent Incident"

.

NO

>> Replace front power window motor LH. Refer to 

GW-16, "Removal and Installation"

. After that,

refer to 

PWC-29, "Work Procedure"

.

DRIVER SIDE : Component Inspection

INFOID:0000000009757250

COMPONENT INSPECTION

1.

CHECK FRONT POWER WINDOW MOTOR LH

Check motor operation by connecting the battery voltage directly to power window motor D8.

Is the inspection result normal?

YES

>> Front power window motor LH is OK.

NO

>> Replace front power window motor LH. Refer to 

GW-16, "Removal and Installation"

. After that,

refer to 

PWC-29, "Work Procedure"

.

DRIVER SIDE : Special Repair Requirement

INFOID:0000000009757251

1.

 PERFORM INITIALIZATION PROCEDURE

Perform initialization procedure. 

Refer to 

PWC-29, "Work Procedure"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Check intermittent incident. Refer to 

GI-39, "Intermittent Incident"

.

2.

 CHECK ANTI-PINCH OPERATION

Check anti-pinch operation. 

Refer to 

PWC-30, "Work Procedure"

.

Is the inspection result normal?

YES

>> Inspection end.

NO

>> Refer to 

PWC-43, "DRIVER SIDE : Component Function Check"

.

PASSENGER SIDE
PASSENGER SIDE : Description

INFOID:0000000009757252

Door glass moves UP/DOWN by receiving the signal from main power window and door lock/unlock switch or

power window and door lock/unlock switch RH.

Main power window and door lock/un-

lock switch connector

Terminal

Ground

Continuity

D11

17

No

19

Terminal

Motor condition

(+)

(–)

1

3

UP

3

1

DOWN