Nissan Leaf. Manual - part 901

LAN-66

< DTC/CIRCUIT DIAGNOSIS >

[CAN]

M&A BRANCH LINE CIRCUIT

M&A BRANCH LINE CIRCUIT

Diagnosis Procedure

INFOID:0000000010120387

1.

CHECK CONNECTOR

1. Turn the power switch OFF.

2. Disconnect the 12V battery cable from the negative terminal. Refer to 

LAN-26, "Precautions for Removing

Battery Terminal"

.

3. Check the terminals and connectors of the combination meter for damage, bend and loose connection

(unit side and connector side).

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair the terminal and connector.

2.

CHECK HARNESS FOR OPEN CIRCUIT

1. Disconnect the connector of combination meter.

2. Check the resistance between the combination meter harness connector terminals.

Is the measurement value within the specification?

YES

>> GO TO 3.

NO

>> Repair the combination meter branch line.

3.

CHECK POWER SUPPLY AND GROUND CIRCUIT

Check the power supply and the ground circuit of the combination meter. Refer to 

MWI-85, "COMBINATION

METER : Diagnosis Procedure"

.

Is the inspection result normal?

YES (Present error)>>Replace the combination meter. Refer to 

MWI-102, "Removal and Installation"

.

YES (Past error)>>Error was detected in the combination meter branch line.

NO

>> Repair the power supply and the ground circuit.

Combination meter harness connector

Resistance (

Ω)

Connector No.

Terminal No.

M34

19

18

Approx. 54 – 66

LAN

STRG BRANCH LINE CIRCUIT

LAN-67

< DTC/CIRCUIT DIAGNOSIS >

[CAN]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

STRG BRANCH LINE CIRCUIT

Diagnosis Procedure

INFOID:0000000010120388

1.

CHECK CONNECTOR

1. Turn the power switch OFF.

2. Disconnect the 12V battery cable from the negative terminal. Refer to 

LAN-26, "Precautions for Removing

Battery Terminal"

.

3. Check the terminals and connectors of the steering angle sensor for damage, bend and loose connection

(unit side and connector side).

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair the terminal and connector.

2.

CHECK HARNESS FOR OPEN CIRCUIT

1. Disconnect the connector of steering angle sensor.

2. Check the resistance between the steering angle sensor harness connector terminals.

Is the measurement value within the specification?

YES

>> GO TO 3.

NO

>> Repair the steering angle sensor branch line.

3.

CHECK POWER SUPPLY AND GROUND CIRCUIT

Check the power supply and the ground circuit of the steering angle sensor. Refer to 

BRC-58, "Wiring Dia-

gram"

.

Is the inspection result normal?

YES (Present error)>>Replace the steering angle sensor. Refer to 

BRC-165, "Removal and Installation"

.

YES (Past error)>>Error was detected in the steering angle sensor branch line.

NO

>> Repair the power supply and the ground circuit.

Steering angle sensor harness connector

Resistance (

Ω)

Connector No.

Terminal No.

M30

5

2

Approx. 54 – 66

LAN-68

< DTC/CIRCUIT DIAGNOSIS >

[CAN]

A-BAG BRANCH LINE CIRCUIT

A-BAG BRANCH LINE CIRCUIT

Diagnosis Procedure

INFOID:0000000010120389

WARNING:

Always observe the following items for preventing accidental activation.

• Before servicing, turn power switch OFF, disconnect 12V battery negative terminal, and wait 3 min-

utes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

1.

CHECK CONNECTOR

1. Turn the power switch OFF.

2. Disconnect the 12V battery cable from the negative terminal. Refer to 

LAN-26, "Precautions for Removing

Battery Terminal"

.

3. Check the terminals and connectors of the air bag diagnosis sensor unit for damage, bend and loose con-

nection (unit side and connector side).

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace the main harness.

2.

CHECK AIR BAG DIAGNOSIS SENSOR UNIT

Check the air bag diagnosis sensor unit. Refer to 

SRC-34, "Work Flow"

.

Is the inspection result normal?

YES

>> Replace the main harness.

NO

>> Replace parts whose air bag system has a malfunction.

LAN

AV BRANCH LINE CIRCUIT

LAN-69

< DTC/CIRCUIT DIAGNOSIS >

[CAN]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

AV BRANCH LINE CIRCUIT

Diagnosis Procedure

INFOID:0000000010120390

1.

CHECK CONNECTOR

1. Turn the power switch OFF.

2. Disconnect the 12V battery cable from the negative terminal. Refer to 

LAN-26, "Precautions for Removing

Battery Terminal"

.

3. Check the terminals and connectors of the AV control unit for damage, bend and loose connection (unit

side and connector side).

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair the terminal and connector.

2.

CHECK HARNESS FOR OPEN CIRCUIT

1. Disconnect the connector of AV control unit.

2. Check the resistance between the AV control unit harness connector terminals.

-

Without BOSE audio system

-

With BOSE audio system

Is the measurement value within the specification?

YES

>> GO TO 3.

NO

>> Repair the AV control unit branch line.

3.

CHECK POWER SUPPLY AND GROUND CIRCUIT

Check the power supply and the ground circuit of the AV control unit. Refer to the following.

• Without BOSE audio system: 

AV-291, "AV CONTROL UNIT : Diagnosis Procedure"

• With BOSE audio system: 

AV-453, "AV CONTROL UNIT : Diagnosis Procedure"

Is the inspection result normal?

YES (Present error)>>Replace the AV control unit. Refer to the following.

• Without BOSE audio system: 

AV-318, "Removal and Installation"

• With BOSE audio system: 

AV-488, "Removal and Installation"

YES (Past error)>>Error was detected in the AV control unit branch line.

NO

>> Repair the power supply and the ground circuit.

AV control unit harness connector

Resistance (

Ω)

Connector No.

Terminal No.

M96

43

23

Approx. 54 – 66

AV control unit harness connector

Resistance (

Ω)

Connector No.

Terminal No.

M103

43

23

Approx. 54 – 66