Nissan Leaf. Manual - part 276

C1AC1 CONTROL MODULE

BR-425

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

G

H

I

J

K

L

M

A

B

BR

N

O

P

7. Check the 15A fuse (#75).

8. Check the continuity and for short circuit between harness connector terminal 28 of electrically-driven

intelligent brake unit and 15A fuse (#75).

Is the inspection result normal?

YES

>> Perform trouble diagnosis for 12V battery power supply. Refer to 

PG-15, "Wiring Diagram — Bat-

tery Power Supply —"

.

NO

>> Repair or replace error-detected parts and GO TO 10.

10.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

1. Connect the electrically-driven intelligent brake unit harness connector.

2. Connect 12V battery cable to negative terminal.

3. Turn the power switch OFF to ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

4. Repeat step 3 two or more times.

CAUTION:

Be sure to wait for 5 seconds or more after turning the power switch OFF.

5. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.

6. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for

3 minutes or more with all doors closed.

CAUTION:

Never operate the vehicle while waiting.

7. Turn the power switch ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

8. Start CONSULT and erase self-diagnosis result of “BRAKE”.

9. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.

10. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for

3 minutes or more with all doors closed.

CAUTION:

Never operate the vehicle while waiting.

11. Turn the power switch ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

12. Depress brake pedal by 100 mm (3.94 in) or more, and hold the position for 5 seconds or more.

13. Release brake pedal.

14. Start CONSULT and perform “BRAKE” self-diagnosis.
Is DTC “C1AC1” detected?

YES

>> GO TO 11.

NO

>> INSPECTION END

11.

CHECK GROUND CIRCUIT

1. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.

2. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for

3 minutes or more with all doors closed.

CAUTION:

Never operate the vehicle while waiting.

3. Disconnect 12V battery cable from negative terminal. Refer to 

BR-6, "Precaution for Removing 12V Bat-

tery"

.

4. Disconnect the electrically-driven intelligent brake unit harness connector.

5. Check the continuity between electrically-driven intelligent brake unit and ground.

Is the inspection result normal?

YES

>> GO TO 13.

Electrically-driven intelligent brake unit

—

Continuity

Connector

Terminal

E34

32

Ground

Existed

BR-426

< DTC/CIRCUIT DIAGNOSIS >

C1AC1 CONTROL MODULE

NO

>> Repair or replace error-detected parts and GO TO 12.

12.

PERFORM SELF-DIAGNOSIS (5)

With CONSULT

1. Connect the electrically-driven intelligent brake unit harness connector.

2. Connect 12V battery cable to negative terminal.

3. Turn the power switch OFF to ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

4. Repeat step 3 two or more times.

CAUTION:

Be sure to wait for 5 seconds or more after turning the power switch OFF.

5. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.

6. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for

3 minutes or more with all doors closed.

CAUTION:

Never operate the vehicle while waiting.

7. Turn the power switch ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

8. Start CONSULT and erase self-diagnosis result of “BRAKE”.

9. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.

10. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for

3 minutes or more with all doors closed.

CAUTION:

Never operate the vehicle while waiting.

11. Turn the power switch ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

12. Depress brake pedal by 100 mm (3.94 in) or more, and hold the position for 5 seconds or more.

13. Release brake pedal.

14. Start CONSULT and perform “BRAKE” self-diagnosis.
Is DTC “C1AC1” detected?

YES

>> GO TO 13.

NO

>> INSPECTION END

13.

CHECK DATA MONITOR (1)

With CONSULT

1. Connect the electrically-driven intelligent brake unit harness connector.

2. Connect 12V battery cable to negative terminal.

3. Turn the power switch OFF to ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

4. Repeat step 3 two or more times.

CAUTION:

Be sure to wait for 5 seconds or more after turning the power switch OFF.

5. Start CONSULT and select “BRAKE” and “DATA MONITOR” according this order.

6. Check the “MOTOR POWER SUPPLY” and “CONTROL MODULE POWER”. Refer to 

BR-33, "Reference

Value"

.

Is the inspection result normal?

YES

>> GO TO 14.

NO

>> Replace the electrically-driven intelligent brake unit. Refer to 

BR-510, "Removal and installation"

.

14.

PERFORM SELF-DIAGNOSIS (6)

With CONSULT

1. Turn the power switch OFF to ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

2. Repeat step 1 two or more times.

CAUTION:

C1AC1 CONTROL MODULE

BR-427

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

G

H

I

J

K

L

M

A

B

BR

N

O

P

Be sure to wait for 5 seconds or more after turning the power switch OFF.

3. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.

4. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for

3 minutes or more with all doors closed.

CAUTION:

Never operate the vehicle while waiting.

5. Turn the power switch ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

6. Start CONSULT and erase self-diagnosis result of “BRAKE”.

7. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.

8. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for

3 minutes or more with all doors closed.

CAUTION:

Never operate the vehicle while waiting.

9. Turn the power switch ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

10. Depress brake pedal by 100 mm (3.94 in) or more, and hold the position for 5 seconds or more.

11. Release brake pedal.

12. Start CONSULT and perform “BRAKE” self-diagnosis.
Is DTC “C1AC1” detected?

YES

>> GO TO 15.

NO

>> INSPECTION END

15.

CHECK DATA MONITOR (2)

With CONSULT

1. Turn the power switch OFF to ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

2. Repeat step 1 two or more times.

CAUTION:

Be sure to wait for 5 seconds or more after turning the power switch OFF.

3. Start CONSULT and select “BRAKE” and “DATA MONITOR” according this order.

4. Check the “CONTROL MODULE TEMP”. Refer to 

BR-33, "Reference Value"

.

“CONTROL MODULE TEMP” is 150 

°C (302 °F) or more?

YES

>> GO TO 16.

NO

>> INSPECTION END

16.

CHECK MOTOR ROOM

Check for any locations of abnormal heating around the electrically-driven intelligent brake unit.
Are there any heated locations?

YES

>> Perform diagnosis of the heated locations, and wait for the temperature to fall. GO TO 17.

NO

>> Replace the electrically-driven intelligent brake unit. Refer to 

BR-510, "Removal and installation"

17.

PERFORM SELF-DIAGNOSIS (7)

With CONSULT

1. Turn the power switch OFF to ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

2. Repeat step 1 two or more times.

CAUTION:

Be sure to wait for 5 seconds or more after turning the power switch OFF.

3. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.

4. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for

3 minutes or more with all doors closed.

CAUTION:

Never operate the vehicle while waiting.

5. Turn the power switch ON without depressing the brake pedal.

BR-428

< DTC/CIRCUIT DIAGNOSIS >

C1AC1 CONTROL MODULE

CAUTION:

Never set the vehicle to READY.

6. Start CONSULT and erase self-diagnosis result of “BRAKE”.

7. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.

8. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for

3 minutes or more with all doors closed.

CAUTION:

Never operate the vehicle while waiting.

9. Turn the power switch ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

10. Depress brake pedal by 100 mm (3.94 in) or more, and hold the position for 5 seconds or more.

11. Release brake pedal.

12. Start CONSULT and perform “BRAKE” self-diagnosis.
Is DTC “C1AC1” detected?

YES

>> Replace the electrically-driven intelligent brake unit. Refer to 

BR-510, "Removal and installation"

.

NO

>> INSPECTION END