Nissan Leaf. Manual - part 274

C1AC0 CONTROL MODULE

BR-417

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

G

H

I

J

K

L

M

A

B

BR

N

O

P

NO

>> Repair or replace error-detected parts and GO TO 12.

12.

PERFORM SELF-DIAGNOSIS (5)

With CONSULT

1. Connect the electrically-driven intelligent brake unit harness connector.

2. Connect 12V battery cable to negative terminal.

3. Turn the power switch OFF to ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

4. Repeat step 3 two or more times.

CAUTION:

Be sure to wait for 5 seconds or more after turning the power switch OFF.

5. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.

6. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for

3 minutes or more with all doors closed.

CAUTION:

Never operate the vehicle while waiting.

7. Turn the power switch ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

8. Start CONSULT and erase self-diagnosis result of “BRAKE”.

9. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.

10. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for

3 minutes or more with all doors closed.

CAUTION:

Never operate the vehicle while waiting.

11. Turn the power switch ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

12. Depress brake pedal by 100 mm (3.94 in) or more, and hold the position for 5 seconds or more.

13. Release brake pedal.

14. Start CONSULT and perform “BRAKE” self-diagnosis.
Is DTC “C1AC0” detected?

YES

>> GO TO 13.

NO

>> INSPECTION END

13.

CHECK DATA MONITOR (1)

With CONSULT

1. Connect the electrically-driven intelligent brake unit harness connector.

2. Connect 12V battery cable to negative terminal.

3. Turn the power switch OFF to ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

4. Repeat step 3 two or more times.

CAUTION:

Be sure to wait for 5 seconds or more after turning the power switch OFF.

5. Start CONSULT and select “BRAKE” and “DATA MONITOR” according this order.

6. Check the “MOTOR POWER SUPPLY” and “CONTROL MODULE POWER”. Refer to 

BR-33, "Reference

Value"

.

Is the inspection result normal?

YES

>> GO TO 14.

NO

>> Replace the electrically-driven intelligent brake unit. Refer to 

BR-510, "Removal and installation"

.

14.

PERFORM SELF-DIAGNOSIS (6)

With CONSULT

1. Turn the power switch OFF to ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

2. Repeat step 1 two or more times.

CAUTION:

BR-418

< DTC/CIRCUIT DIAGNOSIS >

C1AC0 CONTROL MODULE

Be sure to wait for 5 seconds or more after turning the power switch OFF.

3. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.

4. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for

3 minutes or more with all doors closed.

CAUTION:

Never operate the vehicle while waiting.

5. Turn the power switch ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

6. Start CONSULT and erase self-diagnosis result of “BRAKE”.

7. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.

8. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for

3 minutes or more with all doors closed.

CAUTION:

Never operate the vehicle while waiting.

9. Turn the power switch ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

10. Depress brake pedal by 100 mm (3.94 in) or more, and hold the position for 5 seconds or more.

11. Release brake pedal.

12. Start CONSULT and perform “BRAKE” self-diagnosis.
Is DTC “C1AC0” detected?

YES

>> GO TO 15.

NO

>> INSPECTION END

15.

CHECK DATA MONITOR (2)

With CONSULT

1. Turn the power switch OFF to ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

2. Repeat step 1 two or more times.

CAUTION:

Be sure to wait for 5 seconds or more after turning the power switch OFF.

3. Start CONSULT and select “BRAKE” and “DATA MONITOR” according this order.

4. Check the “CONTROL MODULE TEMP”. Refer to 

BR-33, "Reference Value"

.

“CONTROL MODULE TEMP” is 150 

°C (302 °F) or more?

YES

>> GO TO 16.

NO

>> INSPECTION END

16.

CHECK MOTOR ROOM

Check for any locations of abnormal heating around the electrically-driven intelligent brake unit.
Are there any heated locations?

YES

>> Perform diagnosis of the heated locations, and wait for the temperature to fall. GO TO 17.

NO

>> Replace the electrically-driven intelligent brake unit. Refer to 

BR-510, "Removal and installation"

17.

PERFORM SELF-DIAGNOSIS (7)

With CONSULT

1. Turn the power switch OFF to ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

2. Repeat step 1 two or more times.

CAUTION:

Be sure to wait for 5 seconds or more after turning the power switch OFF.

3. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.

4. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for

3 minutes or more with all doors closed.

CAUTION:

Never operate the vehicle while waiting.

5. Turn the power switch ON without depressing the brake pedal.

C1AC0 CONTROL MODULE

BR-419

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

G

H

I

J

K

L

M

A

B

BR

N

O

P

CAUTION:

Never set the vehicle to READY.

6. Start CONSULT and erase self-diagnosis result of “BRAKE”.

7. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.

8. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for

3 minutes or more with all doors closed.

CAUTION:

Never operate the vehicle while waiting.

9. Turn the power switch ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

10. Depress brake pedal by 100 mm (3.94 in) or more, and hold the position for 5 seconds or more.

11. Release brake pedal.

12. Start CONSULT and perform “BRAKE” self-diagnosis.
Is DTC “C1AC0” detected?

YES

>> Replace the electrically-driven intelligent brake unit. Refer to 

BR-510, "Removal and installation"

.

NO

>> INSPECTION END

BR-420

< DTC/CIRCUIT DIAGNOSIS >

C1AC1 CONTROL MODULE

C1AC1 CONTROL MODULE

DTC Logic

INFOID:0000000010123085

DTC DETECTION LOGIC

DTC REPRODUCTION PROCEDURE

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn power switch OFF and

wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

With CONSULT

1. Turn the power switch OFF to ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

2. Repeat step 1 two or more times.

CAUTION:

Be sure to wait for 5 seconds or more after turning the power switch OFF.

3. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.

4. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for

3 minutes or more with all doors closed.

CAUTION:

Never operate the vehicle while waiting.

5. Turn the power switch ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

6. Start CONSULT and erase self-diagnosis result of “BRAKE”.

7. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.

8. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for

3 minutes or more with all doors closed.

CAUTION:

Never operate the vehicle while waiting.

9. Turn the power switch ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

10. Depress brake pedal by 100 mm (3.94 in) or more, and hold the position for 5 seconds or more.

11. Release brake pedal.

12. Start CONSULT and perform “BRAKE” self-diagnosis.
Is DTC “C1AC1” detected?

YES

>> Proceed to 

BR-421, "Diagnosis Procedure"

.

NO

>> INSPECTION END

DTC

Display item

Malfunction detection condition

Possible causes

C1AC1

CONTROL MODULE TEMP-3

• Temperature of control module that is integrated 

with electrically-driven intelligent brake unit is as 
shown below.

- Control module temperature: 

−50°C (−122°F) ≥ 

Control module temperature

- Control module temperature: 150

°C (302°F) ≤ 

Control module temperature

• A malfunction is detected in the temperature de-

tection circuit of the control module that is inte-
grated with the electrically-driven intelligent 
brake unit.

• Harness or connector
• Electrically-driven intelligent 

brake unit