Nissan Frontier D22. Manual - part 790

 

  Index      Nissan     Nissan Frontier D22 Pickup (1998-2004 year) - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  788  789  790  791   ..

 

 

Nissan Frontier D22. Manual - part 790

 

 

MA-14

RECOMMENDED FLUIDS AND LUBRICANTS

SAE VISCOSITY NUMBER
Gasoline Engine Oil

SAE 5W-30 viscosity oil is preferred for all ambient temperatures.
SAE 10W-30 and 10W-40 viscosity oil may be used if the ambient
temperature is above 

−18°C (0°F).

ANTI-FREEZE COOLANT MIXTURE RATIO

The engine cooling system is filled at the factory with a high-quality, year-round, long life, anti-freeze coolant
solution. The anti-freeze solution contains rust and corrosion inhibitors. Therefore, additional cooling system
additives are not necessary.

CAUTION:

When adding or replacing coolant, be sure to use only a Genuine NISSAN Long Life Anti-freeze
coolant or equivalent with the proper mixture.

Other types of coolant solutions may damage the engine cooling system.

TI1028-C

Outside temperature down to

 

Genuine NISSAN Long Life Anti-

freeze coolant or equivalent

Demineralized water or distilled 

water

°C

°F

-35

-30

50%

50%

ENGINE MAINTENANCE (KA24DE)

MA-15

C

D

E

F

G

H

I

J

K

M

A

B

MA

ENGINE MAINTENANCE (KA24DE)

PFP:00100

Checking Drive Belts

ELS000X8

1.

Inspect belt for cracks, fraying, wear and oil. If necessary, replace.

2.

Inspect drive belt deflection or tension at a point on the belt midway between pulleys using Tool.

NOTE:

Inspect drive belt deflection or tension when engine is cold.

Adjust if belt deflections exceed the limit or if belt tension is not within specifications.

Drive belt tension can be checked at other points on the belt.

AMA150

Tool number

: BT-3373-F

MA-16

ENGINE MAINTENANCE (KA24DE)

DRIVE BELT DEFLECTION AND TENSION

*1: If belt tension gauge cannot be installed at check point shown, check belt tension at a different location on the belt.

Changing Engine Coolant

ELS000X9

WARNING:

To avoid being scalded, never change the coolant when the engine is hot.

Wrap a thick cloth around cap and carefully remove the cap. First, turn the cap a quarter of a turn
to release built-up pressure. Then push down and turn the cap all the way to remove.

DRAINING ENGINE COOLANT

1.

Turn ignition switch ON and set temperature control lever all the way to HOT position or the highest tem-
perature position. Wait 10 seconds and turn ignition switch OFF.

2.

Open the radiator drain plug at the bottom of the radiator, and
remove the radiator filler cap. This is the only step required
when partially draining the cooling system (radiator only). 

Do not to allow the coolant to contact the drive belts. 

3.

When draining all of the coolant in the system for engine
removal or repair, remove cylinder block drain plug and air relief
plug.

Deflection adjustment

Unit: mm (in)

Tension adjustment

*1 Unit: N (kg, lb)

Used belt

New belt

Used belt

New belt

Limit

After adjustment

Limit

After adjustment

Generator

17 (0.67)

10 - 12 (0.39 - 

0.47)

8 - 10 (0.31 - 

0.39)

222.4 (22.7, 

50)

355.8 - 444.8 

(36.3 - 45.4, 80 - 

100)

489.3 - 578.2 (49.9 

- 59.0, 110 - 130)

Air conditioner 
compressor

16 (0.63)

10 - 12 (0.39 - 

0.47)

8 - 10 (0.31 - 

0.39)

200.2 (20.4, 

45)

355.8 - 444.8 

(36.3 - 45.4, 80 - 

100)

489.3 - 578.2 (49.9 

- 59.0, 110 - 130)

Power steering 
oil pump

17 (0.67)

10 - 13 (0.39 - 

0.51)

8 - 10 (0.31 - 

0.39)

222.4 (22.7, 

50)

355.8 - 444.8 

(36.3 - 45.4, 80 - 

100)

489.3 - 578.2 (49.9 

- 59.0, 110 - 130)

Applied pushing 
force

98 N (10 kg, 22 lb)

LMA048

SMA919C

ENGINE MAINTENANCE (KA24DE)

MA-17

C

D

E

F

G

H

I

J

K

M

A

B

MA

4.

Check the drained coolant for contaminants such as rust, corrosion or discoloration.
If the coolant is contaminated, flush the engine cooling system. Refer to 

MA-18, "FLUSHING COOLING

SYSTEM"

 .

REFILLING ENGINE COOLANT

1.

Install the radiator drain plug. Install the reservoir tank and cylinder block drain plug, if removed for a total
system drain or for engine removal or repair.

The radiator must be completely empty of coolant and water.

Apply sealant to the threads of the cylinder block drain plugs. Use Genuine High Performance Thread
Sealant or equivalent. Refer to 

GI-42, "RECOMMENDED CHEMICAL PRODUCTS AND SEALANTS"

 .

2.

If disconnected, reattach the upper radiator hose at the engine side.

3.

Set the vehicle heater controls to the full HOT and heater ON position. Turn the vehicle ignition ON with
the engine OFF as necessary to activate the heater mode.

4.

Install the Tool by installing the radiator cap adapter onto the
radiator neck opening. Then attach the gauge body assembly
with the refill tube and the venturi assembly to the radiator cap
adapter.

5.

Insert the refill hose into the coolant mixture container that is
placed at floor level. Make sure the ball valve is in the closed
position. 

Use Genuine NISSAN Long Life Anti-freeze coolant or equiv-
alent, mixed 50/50 with distilled water or demineralized water.
Refer to 

MA-14, "ANTI-FREEZE COOLANT MIXTURE

RATIO"

 .

6.

Install an air hose to the venturi assembly; the air pressure must
be within specification. 

CAUTION:

The compressed air supply must be equipped with an air dryer.

7.

The vacuum gauge will begin to rise and there will be an audible hissing noise. During this process open
the ball valve on the refill hose slightly. Coolant will be visible rising in the refill hose. Once the refill hose is
full of coolant, close the ball valve. This will purge any air trapped in the refill hose.

SMA580C

Radiator drain plug

: 7.8 - 11.8 N·m (0.8 - 1.2 kg-m , 69 - 104 in-lb)

Cylinder block drain plug

: 34 - 44 N·m (3.5 - 4.5 kg-m, 25 - 33 ft-lb)

Air relief plug

: 7 - 8 N·m (0.7 - 0.8 kg-m, 61 - 69 in-lb)

Engine coolant capacity (without reservoir tank)

MT

: 6.5   (6 7/8 US qt, 5 3/4 Imp qt)

AT

: 6.3   (6 5/8 US qt, 5 1/2 Imp qt)

Reservoir tank

: 0.8   (7/8 US qt, 3/4 Imp qt)

Compressed air 
supply pressure

: 5.7 - 8.5 kPa (5.6 - 8.4 kg/cm

2

 , 

80 - 120 psi)

LLIA0058E

 

 

 

 

 

 

 

Content   ..  788  789  790  791   ..