Nissan Frontier D22. Manual - part 503

 

  Index      Nissan     Nissan Frontier D22 Pickup (1998-2004 year) - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  501  502  503  504   ..

 

 

Nissan Frontier D22. Manual - part 503

 

 

DTC P1491 VACUUM CUT VALVE BYPASS VALVE

EC-1115

[VG33E]

C

D

E

F

G

H

I

J

K

L

M

A

EC

3. 

CHECK VACUUM CUT VALVE BYPASS VALVE OPERATION

 Without CONSULT-II

1.

Turn ignition switch OFF.

2.

Remove vacuum cut valve and vacuum cut valve bypass valve as an assembly.

3.

Apply vacuum to port A and check that there is no suction from
port B.

4.

Apply vacuum to port B and check that there is suction from port
A.

5.

Blow air in port B and check that there is a resistance to flow out
of port A.

6.

Disconnect vacuum cut valve bypass valve harness connector.

7.

Supply battery voltage to the terminal.

8.

Blow air in port A and check that air flows freely out of port B.

9.

Blow air in port B and check that air flows freely out of port A.

OK or NG

OK

>> GO TO 4.

NG

>> GO TO 5.

4. 

CHECK EVAP PURGE LINE

1.

Check EVAP purge line between EVAP canister and fuel tank for clogging or disconnection.

2.

Check EVAP purge port of fuel tank for clogging.

3.

Check EVAP canister. Refer to 

EC-1167, "Component Inspection"

 .

OK or NG

OK

>> GO TO 8.

NG (Step 1)>>Repair it.
NG (Step 2)>>Clean EVAP purge port.
NG (Step 3)>>Replace EVAP canister.

5. 

CHECK BYPASS HOSE

Check bypass hoses for clogging.

OK or NG

OK

>> GO TO 6.

NG

>> Repair or replace hoses.

PBIB0635E

EC-1116

[VG33E]

DTC P1491 VACUUM CUT VALVE BYPASS VALVE

6. 

CHECK VACUUM CUT VALVE BYPASS VALVE

 With CONSULT-II

1.

Perform “VC/V BYPASS/V” in “ACTIVE TEST” mode.

2.

Check air passage continuity and operation delay time under the
following conditions.

Operation takes less than 1 second.

3.

Check air passage continuity and operation delay time under the
following conditions.

 Without CONSULT-II

Operation takes less than 1 second.

OK or NG

OK

>> GO TO 7.

NG

>> Replace vacuum cut valve bypass valve.

7. 

CHECK VACUUM CUT VALVE

Check vacuum cut valve as follows:

1.

Plug port C  and D  with fingers.

2.

Apply vacuum to port A  and check that there is no suction from
port B .

3.

Apply vacuum to port B  and check that there is suction from
port A .

4.

Blow air in port B  and check that there is a resistance to flow out
of port A .

5.

Open port C  and D .

6.

Blow air in port A  check that air flows freely out of port C .

7.

Blow air in port B  check that air flows freely out of port D .

OK or NG

OK

>> GO TO 8.

NG

>> Replace vacuum cut valve.

SEF014Z

Condition

VC/V BYPASS/V

Air passage continuity between A and B

ON

Yes

OFF

No

PBIB1429E

Condition

Air passage continuity between A and B

12V direct current supply between ter-
minals 1 and 2

Yes

No supply

No

PBIB1430E

SEF379Q

DTC P1491 VACUUM CUT VALVE BYPASS VALVE

EC-1117

[VG33E]

C

D

E

F

G

H

I

J

K

L

M

A

EC

8. 

CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR HOSE

1.

Turn ignition switch OFF.

2.

Check disconnection or improper connection of hose connected to EVAP control system pressure sensor.

OK or NG

OK

>> GO TO 9.

NG

>> Repair or replace.

9. 

CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR CONNECTOR

1.

Disconnect EVAP control system pressure sensor harness con-
nector.

2.

Check connectors for water.
Water should not exist.

OK or NG

OK

>> GO TO 10.

NG

>> Replace EVAP control system pressure sensor.

10. 

CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR FUNCTION

Refer to DTC P0452 

EC-934, "DTC Confirmation Procedure"

  or DTC P0453 

EC-940, "DTC Confirmation Pro-

cedure"

 .

OK or NG

OK

>> GO TO 11.

NG

>> Replace EVAP control system pressure sensor.

AEC651A

EC-1118

[VG33E]

DTC P1491 VACUUM CUT VALVE BYPASS VALVE

11. 

CHECK EVAP CANISTER VENT CONTROL VALVE

Check air passage continuity.

 With CONSULT-II

1.

Perform “VENT CONTROL/V” in “ACTIVE TEST” mode.

2.

Check air passage continuity and operation delay time.

Operation takes less than 1 second.

 Without CONSULT-II

1.

Check air passage continuity and operation delay time under the
following conditions.

Operation takes less than 1 second.

If NG or operation takes more than 1 second, clean valve using air
blower or replace as necessary.
If portion B  is rusted, replace control valve.
Make sure new O-ring is installed properly.

OK or NG

OK

>> GO TO 12. 

NG

>> Replace EVAP canister vent control valve.

Condition

VENT CONTROL/V

Air passage continuity between A and B

ON

Yes

OFF

No

SEF013Z

Condition

Air passage continuity 

between A and B

12V direct current supply between 
terminals 1 and 2

No

OFF

Yes

BBIA0309E

 

 

 

 

 

 

 

Content   ..  501  502  503  504   ..